CB Radio
-
Product
USRP‑2932, 20 MHz Bandwidth, 400 MHz to 4.4 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device
781911-01
Software Defined Radio Device
20 MHz Bandwidth, 400 MHz to 4.4 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device - The USRP‑2932 is a tunable RF transceiver with a high-speed analog‑to‑digital converter and digital‑to‑analog converter for streaming baseband I and Q signals to a host PC over 1 Gigabit Ethernet. You can also use the NI USRP‑2930 for the following communications applications: WiFi, WiMax, S‑band transceivers, and 2.4 GHz industrial, scientific, and medical (ISM) band transceivers.
-
Product
Industrial IoT Radio Module
-
PCTEL’s rugged, high power 802.11ac WiFi radio module can be installed in a wide variety of products that accept standard mini-PCIe cards. Purpose-built to support industrial applications, this module’s small form factor makes it ideal for integration into your wireless IT platforms.
-
Product
Software Defined Radio
-
NI software defined radios (SDRs) provide the design solution to rapidly prototype wireless communications systems, which leads to faster results. You can present applications with real-world signals such as multiple input, multiple output (MIMO) and LTE/WiFi testbed.
-
Product
GMDSS Radio
NAVTEX System
-
The NAVTEX system provides the automatic dissemination of local Maritime Safety Information (MSI) by Narrow Band Direct Printing (NBDP) operating in the Forward Error Correction (FEC) broadcast mode (see Section 0 for more details on FEC operation). Depending on the geographical features of its area of responsibility (in main, the length of coastline), the NAVTEX system may be chosen by Administrations as an alternative to providing such information by the Inmarsat-C EGC service.
-
Product
USRP-2945, 10 MHz to 6 GHz, 80 MHz Bandwidth, Reconfigurable USRP Software Defined Radio Device
785263-01
Software Defined Radio Device
10 MHz to 6 GHz, 80 MHz Bandwidth, Reconfigurable USRP Software Defined Radio Device - The USRP-2945 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless receiver systems. This software defined radio reconfigurable device is designed for over-the-air signal acquisition and analysis. It features a two-stage superheterodyne architecture with four independent receiver channels and shares local oscillators for phase-coherent operation. It also offers a Kintex-7 FPGA programmable with the LabVIEW FPGA Module. With these features, the USRP-2945 has the RF and processing performance for applications including spectrum monitoring, direction finding, signals intelligence, wideband recording, and radar prototyping.
-
Product
Radio Communication Tester
CMP200
-
The R&S®CMP200 is an IF tester that combines vector signal analyzer and ARB based generator functionality. The compact integrated solution can be customized with up to three R&S®CMPHEAD30 remote radio heads (RRH), for up/downconverting signals to 5G FR2 frequencies.
-
Product
802.11b/g/n SDIO Radio Module
SX-SDMGN
-
The SX-SDMGN is an 802.11b/g/n radio/baseband SDIO Module designed specifically for low power embedded applications. The radio module design approach also saves cost as the SX-SDMGN provides FCC/MIC modular certification.
-
Product
SPLIT MOUNT RADIO SYSTEM
CFIP PhoeniX C
-
CFIP PhoeniX C split mount system is designed to fit in a classic telecom architecture with a radio located outdoor and a sheltered indoor unit. CFIP PhoeniX C system has compact indoor unit that enables transition from TDM networks to hybrid TDM/IP networks providing up to 64E1, Gigabit Ethernet ports, or up to 16 ASI ports for transferring video signal. Total maximum capacity is up to 366 Mbps full duplex.
-
Product
NEXT GENERATION RADIO PLATFORM
INTEGRA S
-
Integra S is an unbelievably light, energy efficient carrier-grade system that exemplifies an outstanding return on smart engineering - the synergy of high competence in radio electronics and materials science. Slip-fit design allows integration with existing high performance antenna systems or integration with 2+0 aggregation setups for up to 954 Mbps Full Duplex capacity without header compression. Gigabit Power over Ethernet (PoE) port defies simple installation, while dual SFP slots allow for fiber optic installation – giving the user ultimate flexibility in cable design.
-
Product
USRP-2974, 10 MHz to 6 GHz, x86 Processor, GPS-Disciplined OCXO, USRP Software Defined Radio Stand-Alone Device
785606-01
Software Defined Radio Device
The USRP-2974 is built on the LabVIEW reconfigurable I/O (RIO) architecture with an onboard Intel Core i7 processor running the NI Linux Real-Time OS. The USRP-2974 is a USRP Software Defined Radio Stand-Alone Device, meaning that you can target the onboard processor with LabVIEW Communications System Design Suite to deterministically perform processing. The USRP-2974 is also equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock. You can prototype a range of advanced research applications that include stand-alone LTE or 802.11 device emulation; Medium Access Control (MAC) algorithm development; multiple input, multiple output (MIMO); heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
-
Product
USRP‑2932, 20 MHz Bandwidth, 400 MHz to 4.4 GHz Software Defined Radio Device
781909-01
Software Defined Radio Device
20 MHz Bandwidth, 400 MHz to 4.4 GHz Software Defined Radio Device - The USRP‑2922 is a tunable RF transceiver with a high-speed analog‑to‑digital converter and digital‑to‑analog converter for streaming baseband I and Q signals to a host PC over 1 Gigabit Ethernet. You can also use the USRP‑2922 for the following communications applications: WiFi, WiMax, S‑band transceivers, and 2.4 GHz industrial, scientific, and medical (ISM) band transceivers.
-
Product
Radio Frequency (RF) And Microwave Products
-
Enable your 5G, aerospace, defense, test and measurement or industrial RF wireless applications with our portfolio of RF and microwave devices. These include high reliability RF diodes, Gallium Nitride (GaN) and Gallium Arsenide (GaAs) Monolithic Microwave Integrated Circuit (MMIC) amplifiers, frequency translation and power transistor devices, switches, attenuators, varactors, filters and more.
-
Product
Over-the-Air Radio Waveform Analyzer Service
DiagnostX
-
Service enables LMR managers to have all of their active radios evaluated for performance and alignment Over-the-Air, without user intervention. A detailed monthly report will be sent identifying those radios as “Failed”, “Passed” and “Never Received”. This service supports P25 Trunked, P25 Conventional and Legacy systems. Available January 2018
-
Product
Custom Radio Frequency (RF) Receivers & Sources
-
FLO – Frequency Locked Oscillators, IFM – Instantaneous Frequency Measurement, DCU – Digital Control Units, ACU – Antenna Control Units, IDCU – Integrated DCUs, and Other Custom Products
-
Product
Two-Way Radio Communications and High Speed Data Transfer
Leaky Feeder System
-
Leaky Feeder systems offer clear two-way radio communication and high-speed data transfer capabilities throughout your underground complex.PBE’s Leaky Feeder System can be tailored to specific site requirements to provide the best radio coverage and data communications. This two-way radio system can provide complete communications coverage for your site, including above ground surface coverage. PBE offers design, supply, testing and commissioning of temporary and permanent communication infrastructures for underground mines, tunnels, plants and buildings. PBE provides a wide range of leaky feeder system options: conventional leaky feeder system, CMTS system, permanent radiating cable network and hybrid networks.
-
Product
PCI, PCI Express and USB radio clocks
-
Meinberg Funkuhren GmbH & Co. KG
Although the PCI Express is PCI-compliant, PCIe cards are based on a different concept. Less lines are used to transfer the data, for example in the case of PCI plug-in cards.
-
Product
USRP-2901, 70 MHz to 6 GHz, 2-Channel USRP Software Defined Radio Device
784040-01
Software Defined Radio Device
70 MHz to 6 GHz, 2-Channel USRP Software Defined Radio Device - The USRP‑2901 is a tunable RF transceiver with full-duplex, MIMO operation. It offers bus-powered connectivity with USB 3.0 or USB 2.0. You can also use the NI USRP‑2901 for the following communications applications: white space; broadcast FM; public safety; land-mobile, low-power unlicensed device (ISM) bands; sensor networks; amateur radio; or GPS.
-
Product
Ettus USRP X410, 1 MHz to 7.2 GHz, 400 MHz Bandwidth, GPS-Disciplined OCXO, USRP Software Defined Radio Device
787272-01
Software Defined Radio Device
The Ettus USRP X410 integrates hardware and software to help you prototype high-performance wireless systems and perform over-the-air signal generation and analysis. Additionally, the Ettus USRP X410 features a two-stage superheterodyne architecture with four independent transmitter and receiver channels. It also features a Xilinx Zynq Ultrascale+ RFSoC with programmable FPGA supporting the Open Source UHD tool flow as well as LabVIEW FPGA. With these features, the Ettus USRP X410 has the RF and processing performance for applications such as wireless communications prototyping, spectrum monitoring, and signals intelligence. The Ettus USRP X410 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock, which improves frequency accuracy and synchronization.
-
Product
Radio Telemetry
-
Procter & Chester Measurements Ltd
Radio Telemetry: A transmission of data from a remote source via a radio to a receiving station for recording and analysis. Inductance: A contactless method of supplying power to (in this case) a strain gauge bridge. The signal is then transmitted back to the electronics. Slip Ring: Consists of a conductive band mounted on a shaft and is insulated from it. The wheatstone bridge is connected to the bands (usually four off). Fixed brushes or contacts make contact on to the bands to transfer power to the bridge and signal back to the static instrumentation.
