Magnetic Susceptibility
Determines the maximum amount of Electro Static Discharge or Electrical Over Stress a piece of electronic equipment can withstand before damage is incurred.
See Also: Magnetic, Susceptibility, Magnetic Test, Magnetic Field, Magnetic Head, Magnetic Flux, Magnetic Stripe, Magnetic Permeability, H-field
-
Product
Magnetic Susceptibility Meter
SM-20
-
The SM-20 magnetic susceptibility meter is very useful tool for a number of geological and geophysical applications where the unique sensitivity of 10-6 SI units together with its small, shirt-pocket size and low weight are appreciated.
-
Product
Magnetic Susceptibility Meter for Multi-Layer Survey
MULTI KAPPA
-
Multi Kappa instrument serves for fast field survey allowing both spot measurement and mapping by means of several probes. Together with GF Instruments traditional pocket magnetic susceptibility meters cover wide range of demands for accurate susceptibility measurement on ground surface, outcrops and samples of rock and soil. geological survey, archaeology, agriculture and forestry, raw material prospecting, mineralogy, sedimentology, detection of metallic objects, UXO survey.
-
Product
Helmholtz Coils
-
Helmholtz coils is a candidate test apparatus for low frequency magnetic field susceptibility testing on military equipment and subsystems. Use of this coils reduce electromagnetic compatibility (EMC) qualification tests time, and subject the equipment under test (EUT) to a relatively uniform field.
-
Product
Magnetizer
U-Serie
-
MAGNET-PHYSIK Dr. Steingroever GmbH
The pulse magnetizers of the U series are suitable for a wide range of applications in the laboratory and in production. With low energies, they are ideally suited for sensor systems made of ferrite material, which can be magnetized with short cycle times at currents of up to 20 kA. In the energy classes 1,400 Ws and 2,800 Ws, rotors with NdFeB magnets up to a diameter of approx. 60mm are typical applications. With this device, you can magnetize with pulse currents of up to 60 kA.
-
Product
Cut Susceptibility Tester
-
King Design Industrial Co., Ltd.
Equipment conforms to IEC61730 MST12 specification. Pre- or post-round can be selected for control wiring connection. With weights block’s positioning pin is removed before test; and is inserted in the rear positioning hole for the remaining time. Equipped with rings at both front and rear end; used to connect a rope and control the driving direction. Use replaceable special cutting chip.
-
Product
Magnetizer
M-Serie
-
MAGNET-PHYSIK Dr. Steingroever GmbH
With a maximum energy of 5,000 Ws, the M-series magnetizers perfectly complement our standard range of devices. They offer the extensive functionality of the X-series in a compact housing that is mobile and flexible in use.
-
Product
Magnets
-
The Danfysik accelerator magnet program covers standard and custom-built magnets, ranging from small correctors to very large spectrometer magnets of more than 100 metric tons
-
Product
Magnetizer
-
MAGSYS magnetizers allow the magnetization, adjustment and also the demagnetization of isotropic and anisotropic magnetic materials of different sizes. In particular, all highly coercive magnetic materials, such as Sm2Co17 or plastic-bonded NdFeB magnets, can be magnetized easily and with short cycle times. In addition to raw magnets, e.g. directly after production, complete workpieces with magnets already installed can also be magnetized.
-
Product
Magnetic Flaw Detector (Magnetic Yoke)
NOVOTEST MPD-DC
-
Magnetic Flaw Detector (Magnetic Yoke) NOVOTEST MPD-DC applies in circumstances where the electric equipment mustn’t be used or prohibited by the rules.
-
Product
Magnet Tester
MP
-
Computer aided measuring desk for automatic measurement of hysteresis loop of hard magnetic materials. Use pole pieces with integrated measuring coils, or J-compensated surrounding coils.
-
Product
Magnetic Sensors
-
Magnetic proximity sensors are characterized by the possibility of large switching distances, available from sensors with small dimensions. They detect magnetic objects (usually permanent magnets), which are used to trigger the switching process. As the magnetic fields are able to pass through many non-magnetic materials, the switching process can also be triggered without the need for direct exposure to the target object. By using magnetic conductors (e.g., iron), the magnetic field can be transmitted over greater distances so that, for example, the signal can be carried away from high temperature areas.
-
Product
Magnetic Resonance
-
Bruker's product portfolio in the field of magnetic resonance spectroscopy includes NMR, preclinical MRI, EPR and Time-Domain (TD) NMR. In addition. Bruker delivers the world's most comprehensive range of research tools enabling life science, materials science, analytical chemistry, process control and clinical research. Bruker is also the leading superconductor magnet and ultra high field magnet manufacturer for NMR and MRI solutions.
-
Product
Magnet Testing
Helmholtz Coils
-
A coil arrangement consisting of two coils with the same radius or edge length is called a Helmholtz coil. At the correct distance, these coils are arranged in parallel on the same axis and current flows through them in the same direction. Their magnetic field is then characterized by a large homogeneous area in the center of the coil, which is freely accessible for experiments and measurement tasks. Helmholtz coils can have a circular or square geometric shape.
-
Product
Current Sense Magnetics
-
Current sense magnetics are used as a low loss method for sensing AC current in a circuit and also provide electrical and safety isolation between the source of the current and the measurement circuit. The key parameters for a current sense transformer are the rms current rating (to ensure it does not overheat in the application) and the safety and voltage isolation (to ensure it conforms to the end-application requirements).
-
Product
Magnetic Particle Inspection
-
Is an inspection method used to identify defects on the surface of ferromagnetic materials by running a magnetic current through it.
-
Product
Magnetic Locators
ML Series
-
The ML series offers simple one-handed operation with an easy-to-learn keypad featuring only three buttons - no menus or cumbersome instructions to follow. The audio unit has the volume built into the on/off key; just hold down the key while it cycles through the settings. The ML-1 features strong monotube construction, providing structural integrity you can count on.
-
Product
Reference Magnets
-
Reference Magnets provide a stable and convenient method to verify the accuracy and calibration of Hall Effect Gaussmeters, Teslameters, and Probes.
-
Product
Reference Magnet
-
Reference magnets generate a homogeneous magnetic field in an air gap. They are mainly used to calibrate hall probes for their full scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using reference magnets.
-
Product
PRECISION MAGNETICS ANALYZER
3260B SERIES
-
At the design stage of component development it is vitally important to understand how the component performs under different operating conditions. This might include operation at diverse frequencies, AC drive levels or DC bias currents.
-
Product
Standard Magnetizers
-
The selection of a magnetizing system begins with an analysis of the production requirements, including magnet material, magnet size, magnetizing orientation, number of poles, production speed, magnet measuring, and other operations that are necessary. After careful evaluations of these factors, and reviews of samples and/or drawings, our application engineers can recommend a system that will meet your requirements.
-
Product
Probes, Magnetic Field
EM-6880 | 9 KHz – 520 KHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
Product
Miniature Magnetic Field Sensor
FLC 100
-
Complete miniature fluxgate magnetometer can be used in any application where the sensitivity of Hall- or MR-magnetometers is not sufficient, e. g. measurement of the earth's field, detection of AC field from power lines, vehicle detection, compass navigation, and many others. Due to its low price and low power consumption ideally suited for multi-sensor array systems.
-
Product
Soft Magnetic Tester
Model SMT-700
-
KJS Associates/Magnetic Instrumentation offers the Model SMT-700 computer-automated magnetic test station for measuring the DC and AC magnetization curves, coercive field strength, and core-loss characteristics of magnetically soft materials, including: Si-Fe, Fe-Co, Fe, stainless steel, Ni-Fe alloys, soft ferrites and others. This modern line of laboratory instruments is designed specifically for accuracy, reliability, and ease-of-use.
-
Product
Magnet Testing
m-cat
-
m-cat is a magnetic field mapper for magnetrons which measures the magnetic stray field data of magnetrons on all three spatial axes and also calculates geometric data. This allows sputtering processes to be monitored and optimized, since the setting or status of the magnetron is critical to the subsequent outcome of the coating process.
-
Product
Heating Magnetic Stirrer
Model 802
-
Constant power heating, no-load surface temperature 120 ℃。A thermal protection device of 150 ℃.Max Stirring Capacity 1000mL
-
-
Product
Magnetic Sensors
-
*Reliable detection through non-magnetizable metals*Cylindrical or rectangular types*Small housings with very long sensing ranges*High mechanical stability in case of shock or vibration*Flush or non-flush mountable in non-magnetizable metals
-
Product
Nuclear Magnetic Resonance Equipment
SpecFIT HRC27
-
Low-field Nuclear Magnetic Resonance (NMR-DT) equipment with user-friendly interface software and data analysis under development. Compatible with Industry 4.0
-
-
