Igniter Testers
-
Product
Battery Testers
-
Traceable®Battery Tester checks alkaline, carbon, silver-oxide, mercury, nickel-cadmium, and other batteries. Tests battery voltages from 1.35 to 12 volts on 13 ranges. Accuracy is ±5%
-
Product
Ultrasonic Portable Hardness Tester
UCI-3000
-
Advanced Ultrasonic Hardness Tester UCI 3000 applies ultrasonic contact impedance method to do comparative hardness measurement for testing pieces, with the high accuracy, efficiency, portability and easy operation. UCI 3000 is a high-precision portable device for quick measuring hardness of small fogging, cast material, weld inspection, heat affected zone, Ion-nitride stamping dies and molds, forms, presses, thin walled parts, bearings, tooth flanks, etc. It is used for measuring the hardness within the ranges of main hardness scales – HB, HRC as well as HV.
-
Product
AMIDA 3KS Tester
-
The AMIDA-3KS test system provides a lower cost, cost-optimized test solution for all consumer power management ICs and portable product components. The AMIDA-3KS tester provides 6 board slots in the test head for the required number of analog board channels, thus reducing the overall system procurement cost, making the cost-effectiveness of each board channel 2 times higher and more flexible. The customer's product testing time is greatly shortened.
-
Product
Premise Toner Drop Cable Continuity Tester
RPT-AAA Series
-
Electronic testing tool designed to check the circuit integrity in new or installed cable up to 5,000 feet (1,500 meters) in length LED indicates DC shorts, splitters & other self-grounding devices in cable while a loud audio tone identifies the line carrying the signal Equipped with a right angle male push-on connector to maneuver in tight areas & a female push-on connector for speed toning Tool includes a pocket clip & (1) AAA 1.5V battery.
-
Product
Bluetooth LE Protocol Qualification Tester
conformanceHarmony
-
The conformanceHarmony LE Tester is a robust testing solution recognized by the Bluetooth SIG as a validated test platform, focused on the qualification testing of products to the Bluetooth low energy specification. It is an integrated software/hardware test platform for Bluetooth protocol qualification testing that provides:
-
Product
Electrical Testers
-
UEi Test & Measurement Instruments
Devices designed to test the presence of, rather than measure, electrical conditions.
-
Product
Disk Peel Tester
DRK186
-
Shandong Drick Instruments Co., Ltd.
DRK186 Disk peel tester is applied to test the ink layer bonding strength of plastic film printing and PT print. To test the surface adhesion state of vacuum coating, surface coating, composite process.
-
Product
Bean Bag Snag Tester
TF221
-
TESTEX Testing Equipment Systems Ltd.
Bean Bag Snag Tester, to determine the snagging and picking resistance of knitted and woven fabrics by tumbling fabrics pillows containing a weighted bean bag within two separate test cylinders.
-
Product
Coil-on-Plug Spark Tester
TH458
-
For ignition systems with coil-on plugs, including Ford, Chrysler, Chrysler imports, Mitsubishi, Nissan, and more. Since coil-on plug ignitions do not have plug wires, inductive test equipment cannot be used. Spark tester tests for no-start conditions and measures coil output.
-
Product
Spin Testers and Bearing Assemblies
-
Vidac has created several spin test systems ranging from the basic manually operated model shown here to fully automated machines that can spin the customers components to a specific speed profile. Our 3D design capability ensures the tight tolerance fit required for high speed rotation.
-
Product
Cable Testers
E445
-
Tests 3 pin XLR leads, 2 and 3-pole A-gauge jack leads, RCA (phono) leads, most commonly used fuses, and other continuity paths using test leads supplied. Continuity indication by buzzer.
-
Product
Fiberglass Telescoping Handle for the High Voltage Contact Tester
HV-43
-
Used for checking voltage up to 1,000V AC.Connects to the hot stick end of the High-Voltage Contact Tester (Cat. No. HVCT1).Dielectric pole type-tested & rated for 10kV AC.Comes in a convenient zippered pouch.
-
Product
Moisture Permeability Tester
DRK501F
-
Shandong Drick Instruments Co., Ltd.
The principle of moisture permeable cup weighing method is to measure the transmittance of water vapor to film, sheet, paper and other materials by weighing the weight of moisture permeable cup.
-
Product
Non-Contact Voltage Testers
-
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
-
Product
Insulation Tester Calibrator
DecR
-
SCOPE offers High Resistance, High Voltage Decade Resistance Box - DecR. It contains number of smartly configured precision resistors. They are arranged in such a way that user can obtain desired resistance value by selecting appropriate decade switches. DecR is designed using the high quality specially selected resistors. These range of high ohm resistance decades are ideal for variety of applications, having a voltage rating up to 5 kV. It covers the resistance range from 1 kilo ohm to 1 tera ohm. DecR can also be customized as per requirement. DecR is housed in a rugged case and available in 3 / 4 / 6 / 9 decades or in binding post configuration
-
Product
Automatic Asphalt Content Tester
-
4000g sample capacity, integrated +0.1gm accuracy weighing scale, High temperature ceramic filtration system and afterburner for accurate measurement of bitumen content in asphalt mixes. Automatic operation through user defined automatic end point detection and 24 hour start timer. User defined control of furnace chamber temperature from 200 – 650oC, Digital display and printing of test data through bright LED displays and integrated printer, Software activated mechanical door lock to prevent door from opening during test process and cutting off power from the heating elements upon opening the door. Operates on Single Phase, 220V, 50 Hz, 20 Amp and consumes less than 5000 W.
-
Product
Edge Press Technology Bed of Nails Testers
Rand Edge Press Family
-
Designed for Research & Development and Pre-Production environments to support often reoccurring product design changes. The primary design focus for this fixture is ease in applying engineering changes and resilience to the abuse of applying multiple engineering changes without damage. In R&D and Preproduction, design changes and updates can occur every week. This Rand fixture, unlike normal test fixtures was designed to be easily taken apart and updated. Constantly disassembling modifying and reassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for multiple updates requiring machining, drilling and wiring changes.
-
Product
Lan CAble Testers
-
TES Electrical Electronic Corp.
Tests a wide range of FTP & UTP cables. Tests for wiring faults such as open, shorted reversed.
-
Product
120-600V Solenoid Voltage&Continuity Tester
1867
-
Peaceful Thriving Enterprise Co Ltd
Test voltage from 120-600V AC/DC polarity and continuity.
-
Product
Air Data Computer (ADC) Tester
MS 1122
-
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
Product
Trailer Lighting System Tester
Scanner
-
A Scanner Trailer Lighting System Tester makes the job a lot faster and easier since it powers your trailer's lighting circuits in sequence. You check the operation of all lighting functions in a single walk-around instead of two or three.
-
Product
Scratch Tester
-
Scratch testers from Anton Paar are used to characterize film-substrate systems and to quantify parameters such as adhesive strength and friction force by using a variety of complementary methods. This makes scratch testers invaluable tools for the determination of coating adhesion, scratch resistance, and mar resistance in research, development, and quality control.
-
Product
Motorized Material Testers
-
Motorized force/displacement testers record both force and displacement. Programming is facilitated by the unique program dial using plain language menu screens.
-
Product
Environmental Control System (ECS) Tester
H301
-
The H301 Environmental Control System (ECS) Tester measures and displays parameters required to test and troubleshoot aircraft heating and air conditioning systems. These parameters include temperatures, pressures, AC and DC voltages, DC currents, and resistances.
-
Product
Fatigue Testing Equipment, Flexing Fatigue Tester
EKT-2102DF
-
EKT-2102DF DeMattia Flexing Fatigue Tester is designed in accordance with ASTM D430 and D813 to test the repeat bending strain and flexing on different kinds of vulcanized rubber compound. After Test, the fatigue testing equipment can determine the difference of testing compund such as deformation, elongation, hardness, etc. under different temperature environment in certain of time.
-
Product
Torque Tester
DIS-IPS series (20CL/5C)
-
For managing various torque wrenches, torque drivers, and automatic/semi-automatic machines. The highly compact detector is ideal for automated line measurements. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. Efficient measurement is possible without unwinding work by "OW joint ".
-
Product
500 AMP Carbon Pile Load Tester
710
-
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
Product
Force Distance Tester
925
-
The Model 925 is a low cost force-distance tester. It communicates with a Windows™-based PC to send data into an Excel format. The data can then be viewed and analyzed in tabular or graphical format. Once in the Excel format, the data can be transferred or used in any of the multiple Excel operations. This line of displacement-force test stations has a positional resolution of 0.0025 mm (0.0001 inches). Your test department will appreciate the high accuracy readings provided over the complete travel range.
-
Product
LED 4 Flat Tester
48655
-
Hopkins Manufacturing Corporation
Quickly and easily confirm if your vehicle 4 flat connector wiring is properly installed and functional. Fits on your keychain to keep it handy! LEDs test left/right turn, brake and taillight.
