Discrete I/O
-
Product
Combination Module: 2 Ch. MIL-STD-1553 & 12 Ch. Discrete I/O
CM8
-
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Enhanced 24 Discrete I/O Channels (0 to 60 VDC, 500 mA/Ch.)
DT4
-
The DT4 module (the enhanced version) features 24 programmable channels for either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3 – 60 VCC source. These modules can sense broken input connections and whether an input is shorted to +VCC or to ground. Additional features of the DT4 (Enhanced Version) are listed below.
-
Product
3U OpenVPX Multichannel Discrete I/O Board
68DT1
Multifunction I/O
The 68DT1 is a 3U OpenVPX™ board featuring up to 96-Channels of Standard Functionality (SF) DT1 module-type or Enhanced Functionality (EF) DT4 module-type Discrete I/O functions [foptioned, factory configurable].48-Channels are dedicated as input (voltage or contact sensing with programmable, pull-up/pull-down current sources). An additional 24 or 48-Channels are programmable for either input or output (current source, sink, or push-pull) switching up to 500 mA per channel from an applied 3 – 60 V external VCC source (or sink to ISO-GND). The 68DT1 can sense broken input connections and whether an input is shorted to +VCC or to ground. Additional features of the DT4 EF are listed below. The 68DT1 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for pull-up resistors or mechanical jumpers.
-
Product
24 Ch , Discrete I/O (0 to 60 VDC, 500 mA/Ch.)
DT1
-
The DT1 module features 24 programmable channels for either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3 – 60 VCC source. These modules can sense broken input connections and whether an input is shorted to +VCC or to ground.
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429X
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Rugged Embedded Multifunction I/O System with 10 GB Fiber Optic & 1 GB Copper Ethernet Switch
NIU3E
Multifunction I/O
The NIU3E is a small, rugged, low-power, self-contained multifunction I/O processing system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions and incorporates an Ethernet switch module that offers four (4) 10GBase-SR multimode fiber optic ports and sixteen (16) 10/100/1000Base-T Ethernet ports. The NIU3E can also be configured with one smart Configurable Open Systems Architecture™ (COSA®) function module. The NIU3E boasts a Dual or Quad Core ARM A53 processor for customer application and I/O and communications management. The NIU3E is configured with two 10/100/1000Base-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
3U OpenVPX High Density Multifunction I/O Board
68CB6
Multifunction I/O
The 68CB6 is a Configurable Open Systems Architecture™ (COSA®) 3U OpenVPX™ board that is preconfigured with 10 different “inboard” I/O, measurement and communication functions. This Combination-function Board (CB) provides a full suite of some of the most common & useful function interfaces supporting many different applications. The 68CB6 features a wide but dedicated selection of functions: Standard Functionality Discrete I/O (DT1); Successive Approximation Register (SAR) ±100 V Analog-to-Digital (AD); Isolated High Voltage Analog-to-Digital (ADF); ±10 V Digital-to-Analog (DA); Thermocouple (TC1) or Resistance Temperature Detector (RT1); Full-bridge Strain Gauge (SG1); Transmission/gear box Chip Detection and Fuzz Burn (CD1); LVDT-to-Digital linear (LD6) displacement (position) measurement, AC Reference Source output (AC2); CAN bus communication (CB8). The 68CB6 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for external intermediate circuit considerations such as pull-up resistors or mechanical configuration jumpers. Inboard functions are software controlled and memory addressed, accessed in similar COSA® modular fashion to maintain seamless common NAI Software Support Kit & API/library structures.
-
Product
32-CH Separate I/O Terminal Base
HSL-TB32-MD
-
The HSL-TB32-MD discrete I/O terminal bases provide reliable and convenient wiring for HSL-M series products. The separate connection can make it easy to wiring, and the separate fuse can protect each I/O point. This low cost terminal base is particularly useful for users who need convenient way to construct their own signal ?Vcondition arrangement.
-
Product
MIL-STD-1553 USB & LAN Test & Simulation Module
UXI-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsConcurrent BC, 31 RTs, and BM operations - Physical Bus ReplayFull error injection/detection capabilities - Programmable trigger and capture - Programmable Bus Coupling and Output Voltage Levels - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs) - Operates from a single USB or Ethernet LAN connection - Supports SAE AS4112/4114 protocol testing requirements- Flight Simulyzer™ GUI Analyzer software
-
Product
Data Acquisition System - 3U 5-Slot
DAQ-35CP0G
Data Acquisition Module
is a preconfigured rugged system ideally suited to support a multitude of military/aerospace data acquisition applications that require "SBC-less" remote Gig-E command and control of high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications; Thermocouple Measurement; Discrete I/O; Differential Transceiver and Dual-Port Gig-E Ethernet.
-
Product
Mission Computer Software Integration Rig
MS 1124
-
The HSIR is the ground test facility and it simulates various LRUs/sensors interfaced with the HAWK Mission Computer. RIG consists of Industrial computers with Simulation modules, Acquisition modules, Video generator module and video display monitors. RIG provides the simulated inputs to both the MCs from each simulated sensor/ LRU through hardwired signals, through the MIL-1553B, Arinc 429, RS-422, RS232 and Ethernet etc. The rig is capable of testing two MCs together either of which can be used as the Bus Controller (BC) or the Remote Terminal (RT). The rig provides the facility to monitor and acquire the MIL-1553B, Arinc 429, RS-422, and RS232 Ethernet bus, Analog IOs, Synchro IOs, Discrete IOs and transactions that takes place between the MCs and various sensors/units. The RIG has the capability to test individual MCs also.
-
Product
224 Channel Digital I/O Modular PXI Card
GX5731
Digital I/O
The GX5731 is a 6U modular digital I/O card with 224 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5731 offers the highest density in the industry for a single PXI plug-in board. Of the 224 channels, 128 support TTL levels with the direction of each group of eight channels programmable as input or output. The other 96 channels can be used for customized I/O using MTS' GX57xx series I/O modules.
-
Product
ARINC 429 Interface
RCEI-715A
Interface
The RCEI-715A is an intelligent, high-density, Type II PC Card (PCMCIA) interface that provides up to 12 fully independent ARINC 429/575 channels, along with up to 4 bi-directional avionics-level I/O discretes.
-
Product
3U cPCI I/O & Comm Board
75C3
Multifunction I/O
NAI’s 75C3 is a 3U cPCI multifunction I/O and communication board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed A/D channels and 28 Discrete I/O programmable channels, or with a reference supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Intelligent, Single- or Dual-Channel MIL-STD-1760 Adapter
EXC-1553UNET/Px-1760
-
The EXC-1553UNET/Px-1760 is an intelligent, single- or dual-channel, MIL-STD-1760 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1760 bus, both in the lab and in the field.The EXC-1553UNET/Px-1760 shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.In addition the EXC-1553UNET/Px(S)-1760 provides 8 I/O Discrete signals and an IRIG B input.
-
Product
Aircraft Data Recording
COTS
-
Our powerful and flexible Ballard Avionics I/O Computers provide the platform for Silo Data recording. These rugged, conduction-cooled, COTS devices combine a powerful computer processor, multi-protocol databus interfaces (MIL-STD-1553, ARINC 429, ARINC 717, ARINC 708), Ethernet, USB, serial, discrete I/O, and other I/O in a small, lightweight package. They deliver outstanding performance on the ground and in the air and are routinely deployed on helicopter, fixed wing, ground mobile, and marine platforms.
-
Product
Data & Protocol Converter
uMACC
-
The uMACC is a wholly contained Communications Converter (data converter - protocol converter or translator). Its small size makes it a complete solution for developing & testing both in the lab and in the field.The uMACC can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to Analog
-
Product
Relay I/O Modules
XTA Series
-
These modules are intended for use with BusWorks XT Series discrete I/O or other digital output modules for the purpose of driving high energy loads.
-
Product
ARINC 429 Bus Interfaces
Interface
AIM’s > ARINC 429 test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. The latest versions also support avionics discrete I/O.
-
Product
PMC Module
PMC-601
-
Curtiss-Wright Defense Solutions
The PMC-601 PMC module allows customers to incorporate MIL-STD-1553 and discrete digital I/O connectivity into military and aerospace embedded computing systems. We assure an easy integration with other elements of our product lines, as well as after-sales technical support, life-cycle management services, and the commitment to long-term availability.
-
Product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M4KDiscrete Module
-
The M4KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M4KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports twenty programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each. Ordering Information:The user can set each discrete:• Either as input or output.• Either to TTL (0 – 5V) or Avionics (0 – 32V) voltage levels on inputs and• Either enable or disable external debounce on inputsThere is a 4092 Word FIFO (a string of 1023 discrete entries) containing the data and time tags.The M4KDiscrete module is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
6U CPCI Multifunction I/O Board
78C1
Multifunction I/O
The 78C1 is a universal 6U cPCI Multifunction I/O Board that eliminates the complexity and size constraints of using multiple, independent, single-function cards. This single slot card has six module positions, allowing developers to achieve a custom configuration with any combination of function modules, such as A/D (10-channels), D/A (10-channels), Discrete I/O (16-channels), TTL I/O (16-channels), Differential Multi-Mode Transceivers (11-channels), RTD (6-channels), Synchro/Resolver (4-channels), LVDT/RVDT (4-channels), and Signal Generator (4-channels).
-
Product
PC Card
I/O Mezzanine modules
-
MAX Technologies’ IPM mezzanine modules are available for MIL-STD-1553, ARINC 429, ARINC 561, ARINC 568, ARINC 629, ARINC 708, ARINC 717, SERIAL ASYNC RS-232/422/485, CSDB, ASCB, HDLC/SDLC, Pulse/Frequency generator, Analog, Single and Differential Discrete I/O and more.
-
Product
STANAG3910/EFEX Modules
-
AIM’s STANAG3910/EFEX test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. The latest versions also support avionics discrete I/O. Configurations with dual redundant concurrent HS/LS Bus Controller (BC), Multiple Remote Terminals, and Chronological/Mailbox Bus Monitor operation with full HS/LS protocol error injection/detection, multi-level triggering, advanced capture/filtering and real time bus recording, time stamping and physical bus replay ensure your bus integrity. Support for EFAbus Direct Digital Links (DDL), Fibre Optic DDL (FODDL) and EFAbus Express extensions (Mixed Mode and Dual Mode operation) are available. To support the French ‘Rafale’ aircraft, modules are available with an Electrical Front End. Single Function variants support cost effective solutions. Each module is delivered with a Board Support Package (BSP) containing the onboard driver software, a full Application Programming Interface (API) and detailed getting started and programming guides. Powerful PBA.pro databus test and analysis software is optionally available for all our STANAG3910 modules.
-
Product
72" Cable
RCONSCSI3-6
-
72” cable (with twisted pairs) transitions from the card front I/O connector on the RAR-USB, RAR-XMC, RAR-PCIE, RCEI-530, RCEI-830A, CEI-520/520A, R830RX, MAC2-VXI, RMAC-VME, P-DIS or P-SER to a SCSI-3 connector. This cable is for the RAR-PCIE, RCEI-530, and CEI-520/520A products, where the rear Discrete I/O connector utilizes the CONM50-D37 or other IDC-50 ribbon connector.
-
Product
4 Discrete/Switch I/O Channels (±100 V, 3 A/Ch.)
DT3
-
The DT3 module (the enhanced version) feature 4 independent, high current, isolated, programmable channels that can be used for input voltage measurements (±100 V), or as a bi-directional current switch (up to 3 A per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
Product
RTM Discrete Signal Conditioning Board
MS 3632I
-
CPCI Rear IO Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3639i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
HS-1760 Flight Rated XMC Network Interface Controller
XMC-1760-NIC-CC
-
Avionics Interface Technologies
Dual Channel configurations supporting NC/NC, NC/NT, or NT/NT - 75 Ohm single ended copper or 150 Ohm differential - Eight (8) opto-isolated discrete I/O lines - Rear I/O through the P16 connector - Conduction-cooling and/or conformal coating available - x4 PCIe interface to NIC interfaces, with DMA controller for data movement - Designed for extended temperature operations - ANSI Application interface supporting C development - Device driver support: Windows, Linux, & VxWorks (others on request)
-
Product
224 TTL Channels, Digital I/O With 4 Counters PXI Card
GX5732
Digital I/O
The GX5732 is a 6U PXI static digital I/O card with 224 TTL I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5732 offers the highest digital channel density in the industry for a single PXI plug-in board.
