Loopback Testers
-
Product
Battery Resistance Tester
FBR-6100NT
-
Fuzhou Fuguang Electronics Co., Ltd.
FBR-6100NT Battery Resistance Tester is a new generation handheld battery tester of FUGUANG™, which can quickly,intuitively and conveniently judge the deterioration of batteries (lead-acid batteries, lithium iron phosphate batteries and nickel-cadmium batteries, etc.). It has the characteristics of high accuracy, repeat consistency and anti-interference. It is an ideal tool for rapid battery daily check.
-
Product
Electronic Ballast Tester
WT5000
-
WT5000 is the updated version of WT3000 with a super LCD for displaying waveforms and parameters directly, and it includes all the functions and technical parameters of WT3000. Reports can be printed if printer is connected. It also meets the latest requirements for electronic ballasts in international standards IEC 60929, IEC 60969, IEC 61000-3-2, GB/T15144-2005, GB/T17263-1998 and so on.
-
-
Product
Box Compression Tester
-
These advanced Box Compression Testers are PC-controlled systems primarily used in the packaging industry for determination of the compression strength of cartons, containers, cardboard boxes, etc.
-
Product
Electrical Testers
-
Digital voltage and continuity tester with LCD screenAC and DC voltage testing (7 thresholds) with automatic AC or DC detection, audible continuity and single-pole phase test.
-
Product
Ruggedized Field Deployable Tester
PUMA
-
- 18-slot PXI / 4-slot SCXI Chassis- 1.2 GHz Embedded Controller- 4-axis Motion Controller/Simulation- 8-port RS-232 Serial Module- 4-port RS-485 Serial Module- 48 bit Isolated Digital I/O- Reconfigurable multi-function I/O FPGA Module- 5 1/2 digit DMM- 200 MHz 2-channel Scope/Digitizer- Multi-function Data Acquisition (DAQ)- 8-channel Analog Input Module- 6-channel Analog Output Module- General Purpose Switching- RF suite (optional)
-
Product
Continuity Tester with Audible Indication
TEK402
-
The Martindale TEK402 is a low cost, easy to use continuity tester with audible indication. The loud buzzer makes it easy to use in noisy environments.
-
Product
ADSL2+ Tester
-
Shenzhen Guoqin Technology Co., Ltd
*Fast Bit Rates (FAST) and Interleaved Bit Rate (INTL) testing *Line parameter testing*Upstream and Downstream Channel Speed RateLine AttenuationSNR MarginTransmit PowerUtilize Rate*Line Errors*Alarms analysis
-
Product
LAN Testers
-
A cable detector can locate open power cables, either live or without current, up to 300 V. A cable detector can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested.Many cable detector devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy. A cable detector provides a safe way to test wall sockets for which no electrical plans or wiring information is available about the cables or their output. A cable detector is very versatile, as it ensures speed and safety when making holes in walls, ceilings and floors.
-
Product
WAN Tester III
-
The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal hydride batteries and a built-in charger.
-
Product
Flexible Leakage/Line Current Tester
RLM-10+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Low-pass filter equipped, it can be cut the noise which is over 150Hz frequency.●Even Coreless Coil but Least Influence from External Magnetic Field and Residual Current●Superior Flexible CT enables Leakage Current Measurement●Backlight Function useful for measurement in the dark place
-
Product
CDM Tester
-
Tokyo Electronics Trading Co., Ltd.
Determine what level of CDM discharge causes device damage by placing the device package on a metal plate with the pins facing up.
-
Product
AMIDA IGBT Tester
600
-
KVI Source: 1 Channel 4Q V/I Source; ±1000V, ±10mA Source ability; V/I read back at 16 bits resolutions under 100Ks sampling rate ; ±0.2% accurate reading of Range
-
Product
Flocculation Jar Tester
LD-LFC-A11
-
Flocculation Jar TesterLD-LFC-A11is designed to stimulate the process of adding reagents, precipitation, coagulation reaction which occurs in water testing procedures. Features portable, 4 round shaped beakers, each with 0.6 L capacity. With 10 to 1000 rpm speed, this flocculation jar tester conducts synchronous as well as independent running operations. It is used to carry out the jar test during water treatment procedure.
-
Product
Leeb Hardness Tester
-
Shenzhen Graigar Technology Co.,Ltd.
The Leeb rebound hardness test is one of the four most used methods for testing metal hardness. This portable method is mainly used for testing sufficiently large workpieces.
-
Product
Insulation & Earth Resistance Testers
-
KV Hipot Power Test Equipment Co.,Ltd
resistance tester is used to measure the resistance of the earth is called Earth Resistance Tester. All the equipment of the system is grounded through the earth electrode. Unhindered earthing protects electrical equipment and personnel from the fault current.
-
Product
Tumbling Barrel Tester
CX-G13
-
Shenzhen Chuangxin Instruments Co., Ltd.
Tumbling Barrel Tester The Tumbling Barrel Test simulates repeated falls which may occur to such devices as connectors or small remote control units which are normally attached to cables during use.
-
Product
Diamond Testers
-
Napco Precision Instruments Co
Jewelry Tester is an account of full wavelength spectrum analyzer. It can appraise true or false and whether or not dyed of jewelry. its wavelength range from ultraviolet to near infrared. it can test spectral reflectance curve of hundred kinds of jewelry effectively.
-
Product
Digital RCD Testers
-
Used to detect whether the RCD in the circuit can be triggered normally.
-
Product
Installation Safety Testers
-
PeakTech Prüf- und Messtechnik GmbH
This innovative combination meter for testing electrical installations according to VDE 0100 convinces by its technical performance in the high-end range.With the large 3.5 "TFT color display all important safety checks as the RCD-, Voltage-, Loop-, Low-Ohm, Earth resistance and Insulation tests for annual safety-checks and newly installed systems can safely be carried out by the responsible electrical engineer.Since this new development was designed only according to the latest standards, the required measuring values can be even more convenient stored with an App (iOS / Android) via Bluetooth on the mobile phone, saved to an SD card or, when work is completed, from the internal data memory via USB connection to a PC.
-
Product
Shoelace Abrasion Tester
UI-FT39
-
Shoelace Abrasion Tester is used to determine shoe lace to lace abrasion resistance to repeated rubbing.
-
Product
Battery Tester 12V Language
BT12L
-
The Battery Tester 12V Language (BT12L) is an inexpensive, simple and easy tool for testing automotive batteries. It has LED display that consumes very little current and will not drain the battery with repeated testing.
-
-
Product
Insulation Tester
-
Cambridge Instruments & Engineering Co.
'CIE' Insulation Tester is a compact portable unit incorporating most modern features used for direct reading of electrical operating machines, Rotating Plant equipment, Stationary apparatus, Insulation Control switching equipment, Distribution networks, Communication cables, Insulators, Transformers, Industrial Installations, Cable, electrical components, wiring and other devices capable of carrying the rated voltages.
-
Product
Impulse Spark Tester
IT-25B
-
While most military standards now favor high frequency spark testing over impulse spark testing, the IT-25B Impulse Spark Tester is available for use in some aeronautic applications that still specify the impulse method. The IT-25B meets the test requirements of military specifications MIL-C-13777E, MIL-W-16878, and NEMA standards for hook-up wire used in high temperature wire applications. This method is favored as an alternate to a wet dielectric test.
-
Product
Handheld Contact Resistance Tester
-
Weshine Electric Manufacturing Co., Ltd
The hand-held Circuit resistance tester is an innovative product. The product is compact, hand-held operation, battery power supply, easy to carry. The product is mainly used in the measurement of contact resistance and other micro-Euclidean resistance of switch contacts. The test speed is fast and the accuracy is high.
-
Product
Universal Hardness Tester
-
A great advantage for testing labs is combining different test methods in one Universal hardness tester, which allows significant cost and space savings, flexibility and user-friendliness. Qualitest offers a competitive range of dead-weight models up to best selling load-cell type systems. These Universal hardness testers can cover Rockwell Regular, Superficial as well as Brinell and Vickers scales in one single machine.
-
Product
Automotive Current Tester LCD Display
77102
-
This automotive current tester with LCD display, plugs directly into the fuse box and can be used on mini, standard and maxi fuse connections. Blades may get hot during use and care should be taken for 2mins whilst they cool down. Fits mini and maxi fuses. Current range 0-80AMP. Safe and easy way to check automotive current.
-
Product
Oil Tan Delta Tester
OTD
-
The Oil Tan Delta (OTD) is a laboratory instrument, which measures the Tan Delta, Resistivity and Relative Permittivity of insulating liquids. These tests give a wider picture of the overall quality of the insulating oil, and will indicate if there is any contamination. Megger has developed features of the OTD to ensure that productivity levels within laboratories are maximised. The microprocessor controlled inductive heater means that there is uniformity of temperature throughout the cell, in compliance with IEC 60247, and for cooling a fan effectively speeds up the cell cooling time. The instrument has a temperature measuring range of 10 to 110 C, with an accuracy of 1 C. It can be set to preheat before testing takes place. The automated oil drain facility negates the need to move the oil vessel. User safety is paramount and with this in mind, Megger have designed independent and dual redundant high voltage cut-off circuitry. If for any reason the user needs to abort the test, this can be done so by pressing any key, immediately terminating the test and removing the high voltage. The design of the cell components maximise oil fill rate but minimise turbulence in oil flow and eliminate trapping of air. With only 32 cell components, it is easy to assemble and disassemble.
-
Product
HYBRID LED CIRCUIT TESTER, 12-42V
MD1651
-
*Tests standard automotive electrical DC 12-42V circuits*Safe for low current circuits and hybrid vehicles*Automatic voltage identification featuring blue for under 40V and red for over 40V
