Loopback Testers
-
-
Product
FMC Loopback Test Board
-
The FMC loopback tester board enables developers and assembly factories to test and characterize the FMC carrier board interfaces. The board features full differential loopbacks on all the FMC high pin count (HPC) connector interfaces including LA, HA, HB, DP and CLK. It also provides a 125MHz transceiver LVDS reference clocks on GBTCLK signals. The FMC loopback board is based on VITA 57 standard with ruggedized conduction or air cooling.
-
Product
Up to 3.2GHz, DB9 Male Fibre Channel Loopback Tester
F9M-LPBK
-
This premium loopback tester support speed of up to 3.2GHz and certified to pass the eye-pattern test.
-
Product
Fiber Optic Loopback MTP
-
Anfkom International Co.,Limited
Anfkom can provide single mode and multimode MTP MPO fiber optic loopbacks. MTP/APC Singlemode loopbacks, and MTP/UPC Multimode loopbacks using high quality US Conec MTP connectors for the highest quality polish and lowest insertion loss. All fiber modes including 9/125, 50/125, 62.5/125. Our MPO MTP loopbacks in standard configurations such as for QSFP modules for a QSFP MTP loopback tester. Custom MPO MTP loopbacks are also available for any configuration. Call or e-mail us about custom MTP MPO loopbacks- we can make any custom configuration you need for your custom MTP loopback needs.
-
Product
KVS Rugged Igniter Tester With Current Monitor
4314
Tester
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
Hoist Tester
Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
Product
MTM-Bus Tester
PXIe-1149.5
BUS Tester
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
Universal A/V Tester
Tester
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
AXIe M8000 Series of BER Testers
Bit Error Rate Tester (BERT)
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
Bit Error Rate Tester (BERT)
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
Receiver Tester
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
120 GBd High-performance BERT
M8050A
Bit Error Rate Tester (BERT)
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
Bit Error Rate Tester - MATRIQ
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
Loopbacks
-
Loopbacck plugs are used for network diagnostics, system configuration testing, and device burn-in. Looping back the signal allows for testing of the optical network.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Tester
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
Fiber Optic Loopback MPO
-
Anfkom International Co.,Limited
Low insertion loss, high return lossMT based Multi-fiber Connector up to 12 fibersHigh credibility and stabilityGood in repeatability and exchangeabilityStandard: Telcordia GR-1435-CORE compliant
-
Product
Fiber Optic Loopback
LC/SC/MTRJ
-
Fiber Loopbacks is designed to provide a media of return patch for a fiber optic signal; typically it is used for fiber optic testing applications or network restorations. For the testing applications, the loopback signal is used for diagnosing a problem. Sending a loopback test to network equipment, one at a time, is a technique for isolating a problem.
-
Product
Loopbacks
-
Amphenol Fiber Systems International
Amphenol Fiber Systems International (AFSI) has developed the Loopback TFOCA and TFOCA-II® plug configuration as an aid to system maintenance and troubleshooting of the tactical cable reels and systems that use them. The Loopback plugs come in a variety of configurations from 0 dB to -23dB to simulate a system operational condition. The use of the Loopback plug enables a technician to test a cable reel in the bi-directional mode by simply swapping leads on the test meter, thus saving considerable time and effort in establishing a systems operational status.
-
Product
Magnetfield Testers
-
The magnetic field tester is suitable for rapid and precise testing of electro-magnetic switches and valves. Their tip lights up to indicate the presence of permanent, DC or AC magnetic fields. Thereby, they are so sensitive that very often it is not necessary to remove covers or cladding from machines and the function check can be carried out without any setting-up time or stopping the machine.
-
Product
Probecard testers
MANAGER
-
Today more complex probe cards are being used. More pins,higher density and larger array requires a new approach inprobe card analysis. With the soaring cost of new generationprobe cards, repair of defective cards becomes an necessity.BE Precision Technology offers all capabilities with the newMANAGER V. Future proof, up to 450 mm full wafer contactprobe cards can be analyzed with up to 88.000 test channels.High-end materials are used to stand extra tough requirements—such as 500 mm diameter diamante viewing window,ultra stiff carbon flip-table, high power Z–stage to generate 600Kg of contact force
-
Product
Cable Testers
E445
-
Tests 3 pin XLR leads, 2 and 3-pole A-gauge jack leads, RCA (phono) leads, most commonly used fuses, and other continuity paths using test leads supplied. Continuity indication by buzzer.
-
Product
Fiber Testers
-
The PingerPro Series provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
-
Product
Mechanical Testers
-
Actron’s wide variety of mechanical testers includes specialty tools, compression testers, vacuum pressure gauges and advanced timing lights. All mechanical testers work effectively on most foreign and domestic vehicles, small engines, motorcycles and other recreational vehicles to save you time on inspections and repairs.
-
Product
Peel Testers
-
Imada offers motorized peel testers in vertical or horizontal configurations.The motorized test stand, digital force gauge and peel fixture apply tension to a safety seals, tapes and laminates.Special attachments and fixtures facilitate 45°, 90°, 180°, ‘T’ and rotary peel tests.Motorized peel testers offer speed control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All peel testers with digital force gauges have data output capability for analysis by optional data acquisition software.
-
Product
EMF Testers
-
TES Electrical Electronic Corp.
Frequency range 10MHz to 8.0 GHz3 axis isoltropic measurements of EMFNon-directional measurement with three channel measurment probe. High dynamic range.Configurable alarm threshold and memory function.
