Battery Impedance
-
Product
6/12/24/36V Conductance Battery Tester
MBT300
-
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
Product
Battery Pack Rotate Test Device
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Pack Rotate Test Device Single storage cell safety testTest object: Battery storage pack or systemRotate the battery pack 360°around X axis with rotation speed of 6°/s; secondly rotate it 90°,180°,270°,360°,and remain for one hour after each move. Then stop and observe for 2 hours.Rotate the batter pack 360°around Y axis with rotation speed of 6°/s; secondly rotate it 90°,180°,270°,360°,and remain for one hour after each move. Then stop and observe for 2 hours.Accept standard: Battery pack or system has no electrolyte leakage, no rupture at case, no fire nor explosion. And remain the connection reliable, the structure intact, the insulation resistance value not less than 100 Omega /v.
-
Product
Battery Test
1260
-
*Basic Battery Load Test*Battery Analysis*Mac*Test*Bad Cell Indicators*Testing the Starter Motor*Low Temperatures Effects
-
Product
Battery Charge Discharge Tester
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Charge Discharge Tester is a multi-function comprehensive tester which is not only a battery charger and Battery discharger, but a battery activator.
-
Product
Battery Conductance Tester
BT-3918
-
Kongter Test & Measurement Co., Limited
The excellent performance of BT-3918 battery conductance tester will help you pick out the weak batteries and ensure battery performance in short time measurement. This test of battery internal resistance or battery conductance is essential for stationary batteries. It is also recommended by latest regulation of IEEE 450, IEEE 1188 and IEEE 1106.
-
Product
Battery Resistance Tester
FBR-6100NT
-
Fuzhou Fuguang Electronics Co., Ltd.
FBR-6100NT Battery Resistance Tester is a new generation handheld battery tester of FUGUANG™, which can quickly,intuitively and conveniently judge the deterioration of batteries (lead-acid batteries, lithium iron phosphate batteries and nickel-cadmium batteries, etc.). It has the characteristics of high accuracy, repeat consistency and anti-interference. It is an ideal tool for rapid battery daily check.
-
Product
Backup Battery Monitor And Switch
-
Renesas offers an automatic battery back-up switch, intended as a low-cost solution for the switching of systems between two power supplies; main and battery backup.
-
Product
Battery Tester
BAT-200
-
Check the batteries! Battery failure is often the common cause for the sensor or instrument failure. Simple to use, portable universal battery tester for the standard and rechargeable batteries.
-
Product
Standby Battery Testers
-
Franklin Electric - Grid Solutions
A user-customizable, flexible, efficient and economical battery management tool for service providers, operations, and maintenance teams.
-
Product
Next Generation Battery Tester
-
Upgrade to Maccor's newest test platform, The Series 6000. While maintaining all of the features of Maccor's high precision hardware, the Series 6000 adds an element that will elevate your testing. The new high-speed control and data collection capabilities are impressive.The Advanced Multi Level Pulse ("AMLP") allows you to create the most complex pulse profiles available.
-
Product
Motorcycle Battery Testers
-
ELAK Motor-Cycle Battery Testers are designed for testing batteries used in motor-cycles, scooters, ATV''s, etc. These testers check the voltage drop of the battery under a fixed load and confirm the status of the battery full, weak or dead. The new generation motor-cycle and scooters are fitted with an electrical start. It is therefore very essential to test these batteries under load, to ensure that the batteries are capable of starting the vehicle.
-
Product
Regenerative Battery Pack Test System
17040
-
Chroma Systems Solutions, Inc.
The 17040 Regenerative Battery Pack Test System is a high precision system specifically designed for secondary battery module and battery pack test. It has an energy regenerative function to greatly reduce power consumption during discharge, and ensure a stable power grid without generating harmonic pollution on other devices – even in dynamic charge and discharge conditions. It is capable of recycling the energy discharged by the battery pack test back to the grid reducing wasted energy that traditional equipment discharges in the form of heat.
-
Product
Battery Extra Load Units
-
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
Product
Standard 1.17 (33.20) - 4.50 (128.00) Battery Probe
CP-2LB-8
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 88Full Travel (mm): 2.25Recommended Travel (mil): 78.7Recommended Travel (mm): 2.00Overall Length (mil): 315Overall Length (mm): 8.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
Product
Battery Analyzers
CA 1550 – Military Version
-
*Portable Battery Charger / Analyzer.*0-25 Amp Charge.*0-50 Amp Discharge.*Fully adjustable.*115/230 Volt AC Input.
-
Product
High-Precision Battery Tester
-
Arbin's High-Precision Battery Tester (HPS) is equipped with state-of-the-art technology, ensuring unmatched accuracy and precision.
-
Product
5V30A High Current Lithium Battery Tester
TOB-BTS-5V30A
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels High Current Lithium Battery Tester For Power Battery Performance Detection
-
Product
Battery and Alternator Analyser for 12V DC Systems
1176
-
Checks battery charge level and alternator output level. 880mm of insulated cable with test probe and earth (crocodile) clip. For 12V DC systems only. Display packed.Warning: For testing DC circuits on vehicles within the voltage range only. Not suitable for testing mains supply AC circuits.
-
Product
Battery Cell Insulation Tester
Chroma 11210
-
Chroma Systems Solutions, Inc.
Chroma 11210 battery cell insulation tester is an instrument used for accurately measuring leakage current (LC) and insulation resistance(IR) of battery jelly-roll/dry-cell as well as other insulation materials. In addition to standard LC/IR measurement, the 11210 has a unique function that detects partial discharge (PD) or flashover that may have occurred inside the insulation material during the high voltage insulation testing process.
-
Product
Automotive Battery Production Line Tester
-
The Production Line Tester (PLT) is typically installed at the end of battery production lines (finishing). An electrical load test after formation charging is essential to assure performance and quality. The energy discharged during this test must be minimized to eliminate the need for recharging after testing.
-
Product
Regenerative Battery Pack Test System
17040E
Test System
High-power testing equipment up to 1,700V/ 4800A/ 1.2MW Multiple safety protections for personnel safety risk management and control of battery testing Flexible Integration for automated battery verification solutions
-
Product
Battery Resistance Tester
BT-3915
-
Kongter Test & Measurement Co., Limited
Regular test of battery internal resistance or battery conductance is essential for stationary batteries. It is also recommended by latest regulation of IEEE 450, IEEE 1188 and IEEE 1106. The excellent performance of BT-3915 for testing battery internal resistance and voltage will help you pick out the weak batteries and ensure their performance in short time measurement.
-
Product
Automatic Battery
BATLV480
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Battery Crush Nail Penetration Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL battery crush nail penetration tester is used to simulate the use, transportation, storage and disposal of various types of batteries under certain temperature conditions, when the battery is crushed (such as compacted garbage) or nail penetration, and to judge the battery safety performance. The battery is qualified as no disintegration, no rupture, and no fire.
-
Product
Battery (EV) Automatic Test System
-
Landrex Technologies Co., Ltd.
Battery (EV) Automatic Test System
-
Product
Automatic Capacitor Batteries
-
Lifasa - International Capacitors, SA
The batteries of capacitors for automatic AT are designed for those applications in which the power levels in the AT network are variable. This type of equipment, with a number of steps normally between 2 and 4 to avoid phenomena in the installation resulting from the connection and disconnection of the capacitors in the electrical network, is controlled by a type MCX regulator, which tunes and regulates the input of the steps according to load levels, taking into account the expected waiting times of AT that between consecutive connections is 600 s., this time we can reduce it to less than 10 s. if we install TP for fast download.
-
Product
CTEK MXS 5.0 Battery Charger
40-206
-
The MXS 5.0 offers a unique eight-step approach to battery care. Fully automatic microprocessor controlled charger with built-in automatic temperature sensor features a unique combination of advanced charging modes and makes the new MXS 5.0 the fastest, most effective and versatile consumer charger CTEK has ever made. Alligator Clamps and Eyelets included.
-
Product
Battery Pack ATS
8700
-
Chroma transfers its successful experience in 8000 ATS which is quite well-known in the power electronics industry to the battery application field by developing the Test Items specifically for the battery industry. It can perform automatic tests on the Battery Management System (BMS), semi products and finished products tests on the production line as well as provide long term maintenance and service to the battery module. 8000 (8700) ATS has flexible hardware architecture that can select a variety of hardware devices, such as DC Power Supply, Electronic Load, LCR Meter and 6 1/2 digits Meter, etc. to comply with different automatic testing requirements for various applications. In addition new hardware and test items can be expanded to meet the demands for inspecting the highly customized battery products with diversified tests. The capabilities supported are:





























