High Definition TV
Digital broadcast television with higher resoultion than NTSC, SECAM and PAL.
-
Product
Ultra High 4.09 (116.00) - 10.00 (283.00) General Purpose Probe
EPA-2G30-2
General Purpose Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 107Recommended Travel (mm): 2.72Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 970Overall Length (mm): 24.64
-
Product
High 3.12 (88.00) - 8.00 (227.00) Bead Probe
BTP-72F-8
Bead Target Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Overall Length (mil): 1,700Overall Length (mm): 43.18
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-010-HI
-
The 40-230-010-HI (PXI) and 42-230-010-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High-concentration, High Flow Ozone Generator
SEMOZON® AX8407
-
The SEMOZON AX8407 generator converts pure oxygen into ozone through silent electrical discharge and achieves high output and high concentration level. It requires only minute levels of dopant nitrogen gas, far below the levels required for competitive ozone generators. As a result, the presence of contaminants, e.g. NOx compounds, is extremely low.
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-150
Programmable Resistor Modules
The 40-297A-150 (PXI) and the 42-297A-150 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 1.51 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI High Density Multiplexer, 20-Bank, 4-Channel, 1-Pole (SP4T)
40-615A-013
Multiplexer Module
The 40-615A-013 is a 20-bank, 4-channel, 1-pole (SP4T) MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
High Resolution Microscope for Multi-fiber Connector
D SCOPE MT
-
The new D SCOPE MT microscope for MTP/MPO connectors is the fastest on the market. In the same measurement cycle, D Scope MT checks every optical fiber surface condition, and allows the operator to control the cleanliness of the connector endface and guideholes.
-
Product
High Voltage Benchtop Battery Tester 1000V Max input
BT3564
-
Hioki benchtop battery testers support simultaneous high-speed measurement of the internal resistance and battery voltage of EV and PHEV battery packs. The BT3564 Battery HiTester can measure pack voltage and total resistance, as well as bus bar resistance up to 1000V.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2.5Ω To 472Ω
50-298-020
Programmable Resistor Modules
The 50-298-020 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI High Density Mux 5 Channel 16 Pole
40-670A-021-5/16
Multiplexer Module
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
High Speed Gravity Handler
MT9928 xm
-
This well-established test handler provides field-proven reliability and performance. Its modular and scalable design and variety of options allow configuration of the MT9928 exactly according to the test needs. Easy-access design and easy-to-change conversion kit parts support fast and easy package style changes. The MT9928 has a large soak capacity and features the entire tri-temp range at outstanding temperature accuracy and stability.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-225-HI
-
The 40-230-225-HI (PXI) and 42-230-225-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 13.6kΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-110
Programmable Resistor Modules
The 40-297A-110 (PXI) and the 42-297A-110 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 31 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Ultra High 4.09 (116.00) - 10.00 (283.00) General Purpose Probe
EPA-2D-2
General Purpose Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 107Recommended Travel (mm): 2.72Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 970Overall Length (mm): 24.64
-
Product
High Voltage Pulse Attenuators
-
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
Product
1,000 Watt AC/DC (High Voltage Output) Power Supplies
56XS2
Programmable Power Supply
NAI’s 56XS2 is a conduction-cooled, 1,000 Watt AC/DC Power Supply that converts a 3-phase, AC input into a single HIGH VOLTAGE +270 VDC output at 1,000 Watts.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-154
Programmable Resistor Modules
The 40-297A-154 (PXI) and the 42-297A-154 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 22.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Compact High Resolution CMOS or CCD Spectrometer
MiniVS70
-
MiniVS70 is the latest evolution of the cost-effective high performance family of mini-spectrometers from HORIBA Scientific. This MiniVS70 system for industrial applications uses a modified miniaturized VS70 optical engine which is optimized for the UV-VIS-NIR spectral range. The MiniVS70 is based on a high performance aberration corrected concave grating fitted with a custom order-sorting filter to eliminate higher orders.
-
Product
High Performance Bench Meter for Universal pH Applications
Starter 5000
-
Backed by OHAUS' century-old commitment to providing precise measurement, Starter 5000 provides accurate pH and ORP measurement for high-level experiments and research. Enhanced features, advanced technology, and high performance have been combined to support complex laboratory tasks requiring pH measurement. Starter 5000's performance is propelled by a 1000 item library, 10 sensors for calibration storage, 8 predefined and 1 self-defined buffer groups, 3 endpoint modes and GLP mode.
-
Product
High 2.90 (82.20) - 12.60 (357.00) Switch Probe
TSP100-FK180-3
Switch Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 64-Channel, 1-Pole
40-614D-010
Multiplexer Module
The 40-614D-010 (PXI) and 42-614D-010 (PXIe) 2-bank, 64-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
High Temperature Operating Life
7000 Series
-
With ever decreasing geometries, the way we perform HTOL requires careful consideration. In lower geometry device leakage currents are not only higher but vary greatly. Temperature control at DUT level – required to achieve correct junction temperature at every DUT. For higher geometries, HTOL can be performed in a more traditional way but with devices consuming more power, the ambient temperatures required varies greatly. Multiple temperature zones are required – multi zones system or multiple smaller HTOL systems.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-155-HI
-
The 40-230-155-HI (PXI) and 42-230-155-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 43.424MΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High 0.75 (21.00) - 8.00 (227.00) Long Travel Bead Probe
BPLT-25HF-8
Bead Target Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, Alternate Spring 400 mil / 10,16 mm, High Spring: 400 mil / 10,16 mm, Ultra High Spring: 350 mil / 8,89 mm
-
Product
High Voltage Amplifier
HA-800
-
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
Product
PCI High Density Matrix, Dual 20x4 1-Pole
50-511A-021
Matrix Switch Module
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards.
-
Product
High 2.90 (82.20) - 12.60 (357.00) Switch Probe
TSP100-H180-3
Switch Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 11-Channel, 2-Pole
42-321-126-HI
Multiplexer Module
The 40-321-126-HI (PXI) and 42-321-126-HI (PXIe) are quad 11-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
High 2.84 (81.00) - 8.00 (227.00) High Performance Lead Free Probe
LFRE-25I15-8
ICT/FCT Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02





























