-
Product
1 GHz A/D and D/A with Virtex-7 FPGA - 3U VPX
Model 52730
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One 1 GHz 12-bit A/D- One 1 GHz 16-bit D/A- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual uSync clock/sync for multiboard synchronization- PCI Express (Gen. 1 and 2) interface up to x8- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX System Specification)- Ruggedized and conduction-cooled versions available
-
Product
4-Channel DAQ Module
FMC176
-
Sundance Multiprocessor Technology Ltd.
The FMC176 is a quad channel ADC and dual channel DAC FMC. This daughter card provides four 14-bit A/D channels at 250Msps and two 14-bit D/A channels at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC176 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
Power Quality Analyzer
PQM-703
-
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
Product
Clock And Trigger Synchronization System
CLKSYNC-40
-
CLKSYNC-40 is a clock and trigger distribution system that provides multiple, independent copies of clock and trigger signals for multi-channel, Giga-sample ADC and DAC boards. Up to sixteen independent ADC or DAC clocks and triggers are synchronized.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - 3U VPX
Model 52660
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Supports gigabit serial fabrics including PCI Express, Serial RapidIO and Xilinx Aurora- Four 200 MHz 16-bit A/Ds- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
Product
Channel Serial Lab versions
-
5.0 GT/s 24-lane, 6-port PCIe Gen2 SwitchAll peripheral slots and CPU slot has PCIe interface Gen2 with x4 width10, 100 MHz clock at each peripheral slot1 PPS clock at each peripheral slotGPS module, navigate down to -162 dBm and -148 dBm coldstartMEMS Digital Motion Sensor with ±6g/±12g/±24g dynamically selectable fullscale, 6D orientation detectionHumidity and Temperature Sensor
-
Product
Master Clock
5700
-
Quintech Electronics and Communications Inc.
The 5700MSC-IP is an IP network grandmaster clock and video master sync generator capable of being referenced to GPS and GLONASS global navigation satellite constellations with the included smart antenna, and additionally Galileo and Beidou in L1 and L5 bands with the optional MSC-RF-ADAPT-720 GNSS receiver and MSC-RF-HEAD-720 Dual Band multi-GNSS RF antenna.
-
Product
FPGA Mezzanine Card
FMC116
-
The FMC116 is a 16-channel ADC FMC daughter card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides 16 A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
-
Product
4-Channel DAQ Module
FMC144
-
Sundance Multiprocessor Technology Ltd.
The FMC144 is an analog-to-digital (A/D) and digital-to-analog (D/A) FMC daughter card that provides four 16-bit A/D channels at 370MSPS and four 16-bit D/A channels at 2.5GSPS which can be clocked by an internal clock source (optionally locked to an external reference) or by an externally-supplied sample clock.
-
Product
ARM LPC2364 Board
MS 1541
-
- 128KB On chip Flash- 16*2 line LCD Module interface- Two CAN channel at 1MPBS- Ethernet interface which supports 10/100 MBPS- Full Modem RS232 interface- RS485 interface- RTC (Real Time Clock)- 2048 bits serial EEPROM with data protect and sequential read.- 24 ULN outputs of 12V level.- Eight 110V DC inputs interface.- Six digital inputs interface- Four on board keys interface- Power delay circuit for external use- ON board inspection circuit
-
Product
Low Profile PCI Express 8-Port
7803e
-
The 7803e low-profile PCI Express serial interface provides eight RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize 16C954 UARTs with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
OnyxFX FlexorSet 4-Ch. 250 MHz A/D, 2-Ch. 800 MHz D/A - 3U VPX
Model 5973-312
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 250 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Also available as Model 7070-312- See comparable JadeFX Xilinx Kintex UltraScale FPGA Family:Model 5983 JadeFX Kintex UltraScale Processor and FMC Carrier - 3U VPX
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
Mobile Apps for iOS and Android
LoggerLink
-
LoggerLink Mobile Apps are simple yet powerful tools that allow an iOS or Android device to communicate with our CR200X, CR800, CR850, CR1000, CR3000, or CR6 dataloggers via an IP device (NL115, NL116, NL120, NL121, NL201, NL240, RavenXTV, RavenXTG, LS300G). LoggerLink for Android also supports Bluetooth communication for these same dataloggers using an RS-232-Bluetooth adapter. The apps support field maintenance tasks such as viewing and collecting data, setting the clock, and downloading programs.
-
Product
Power Quality Analyzer
PQM-700
-
*power to the analyzer is supplied from tested mains (internal power supply) and is used in all types of networks from 64 V to 760 V, with particular emphasis on measurements at low voltage poles, due to the ease of connection,*has an independent power supply socket, especially suited for voltage measurements for transformers and DC circuits,built-in real-time clock.
-
Product
PCIe Adapter for VPX
PCIe8LSwVPX3U
-
PCIe8LSwVPX3U is an 8 lane PCIe adapter with switch isolation for VPX development. The switch isolates the spread spectrum clocking found in most PC´s from the VPX port. PCIe 3.0 compliant, 1-8 lanes can be used by the installed VPX.
-
Product
Specialized PXI
-
PXI is an abbreviation for PCI eXtensions for Instrumentation. It is based on the PCI architecture, a commonly-used standard in personal computers, with an industrial connector. A second connector adds instrumentation-specific signals to the backplane, like clock and trigger signals.
-
Product
PCI Direct Digital Synthesizers
SYNTH300 SERIES
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.Software support for Windows Vista, Windows XP,Linux and Labview source code availableFor detailed specifications, please refer to the Synth300_Manual
-
Product
LVDS Digital I/O with Virtex-6 FPGA - 6U VPX
Model 58610
-
- 32 or 64 bits of LVDS digital I/O- One or two LVDS clocks- One or two LVDS data valid- One or two LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAS- One or two DMA controllers move data to and from system memory- Up to 2 or 4 GB of DDR3- PCI Express (Gen. 1 & 2) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- Ruggedized and conduction-cooled versions available
-
Product
PXIe-1095, 18-Slot (5 Hybrid Slots, 11 PXI Express Slots, 1 PXI Express System Timing Slot), Up to 24 GB/s PXI Chassis
785971-01
Chassis
PXIe, 18-Slot (5 Hybrid Slots, 11 PXI Express Slots, 1 PXI Express System Timing Slot), Up to 24 GB/s PXI Chassis - The PXIe-1095 features a high-bandwidth backplane and up to 82 W of power and cooling in every slot to meet a wide range of high-performance test and measurement application needs. The chassis incorporates two hot-swappable power supplies to improve the mean time to repair (MTTR) of the PXI system; it also offers a Timing and Synchronization option that includes a built-in oven-controlled crystal oscillator (OCXO) for increased clock accuracy and external clock and trigger routing. It accepts PXI Express modules in every slot and supports standard PXI hybrid-compatible modules in up to five slots.
-
Product
Programmable Multifrequency Clock Synthesizer - 6U VPX
Model 5791
-
- Simultaneous synthesis of up to five different clocks- Eight SMC clock outputs- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 to 100 MHz- Four programmable VCXOs with 32-bit tuning resolution- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status over the VPX backplane
-
Product
PXI Three Channel Function Generator
41-620-003
Function Generator
The 41-620 is a compact 3 channel function generator provided in a PXI 3U single slot module. It is capable of generating sine waves to 10MHz with 48-bit frequency resolution referenced to the 10MHz PXI clock or to an external standard. The 41-620 can generate arbitrary waveforms loaded into the internal 256k memory, allowing the function generator to emulate many waveform types, including the typical waveforms of automotive and aerospace sensors.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - XMC
Model 71760
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 200 MHz 16-bit A/Ds- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Advanced reconfigurability features- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Continuous Time Interval Analyzer - PXI
GT668PXI-40
-
A true breakthrough in high-speed Time Measurement and test technology, GuideTech’s GT668PXI-40 leverages the power of its CTIA continuous time-stamping technology, eliminating the need for supplemental triggers, pattern markers or clock recovery circuits.GuideTech’s CTIAs enables serial interfaces pattern verification and full jitter analysis in milliseconds for fast, automated characterization and high-throughput production test on all ATE platforms, including low-cost and in-house testers.GT668PXI-40 cards can be expanded up to 36 Channels Single Ended Input in a single 3U PXI chassis.
-
Product
Calipers - Dial
-
A precision measuring device with parallel jaws or legs, with a shape similar to a clock face.
-
Product
OnyxFX FlexorSet 8-Channel 250 MHz A/D with DDCs - 3U VPX
Model 5973-317
-
- Supports Xilinx Virtex-7 VXT FPGA- GateXpress supports dynamic FPGA reconfiguration across PCIe- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)Ruggedized and conduction-cooled versions available
-
Product
2-Channel ADC Module
FMC161
-
Sundance Multiprocessor Technology Ltd.
The FMC161 provides one 12-bit A/D channel at 3.6Gsps or two A/D channels at 1.8Gsps clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC161 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
Midi Time Code Reader
MTC
-
MTC - Midi Time Code hardware Analyzer or Analyser /Reader/Decoder. The MTC Decodes any (FX) System Common or System Real-Time Messages and displays them in a clock format, independent from your MTC generating device. The MTC has the same input and HOLD and SCROLL features as described in the MA1 module.
-
Product
Timing and Frequency Solutions
-
Arbiter Systems®, Inc. delivers world class GPS based precision timing and frequency solutions for a variety of evolving markets. Engineered and manufactured in the USA, Arbiter precision time clocks and supporting products surpass industry standards in terms of accuracy, flexibility, reliability, connectivity and value, and are as at home in the substation as they are in the laboratory.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - XMC
Model 71690
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal - levels with up to 60 dB gain- Programmable analog downconverter to I + Q baseband signals - 4 to 40 MHz bandwidth- Two 200 MHz 16-bit A/Ds digitize the I + Q signals synchronously- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1 & 2) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
