Light Sources
See Also: Lighting, Optical Light Sources, LED Sources, Light Choppers, Opacity, Spectroradiometers
-
product
Optical Light Source
TM3111
TM3111 optical light source is a handheld optical light source, It can provide 1 to 6 wavelengths output to satisfy specific requirements including the 650nm visible light source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer’s needs.
-
product
SFP
4 Gbps
Is specifically designed for high performance integrated duplex data link over multi mode optical fiber. The high-speed oxide VCSEL and photo diode are provided as a light source and a detector, respectively.
-
product
High Accuracy Spectrophotocolorimeter
LMS-3000
• Measure and display the relative spectral power distribution (UV-VIS-NIR) P(λ), chromaticity coordinate, correlated color temperature, rending index, color difference, peak wavelength, luminous flux, luminous flux efficiency and photometry parameters of light source and light material under the control of general PC. • Automatically adjust high-voltage, it not only shortens the measurement time, but also reduces the wear and tear of the instrument • Simultaneously measure the temperature in both environment and integrating sphere to make the data more visually and reliably • Figure of chroma and color difference in test report can be exchanged freely • Color display and print. The relative spectral power distribution (UV-VIS-NIR) P(λ), reports both in English. RS-232-C interface, compatible with all kinds of computer • LSP-500 AC Power source PC RS-232-C interface. compatible with all kinds of computer • Range of wavelength: 380nm～780nm(Special:200nm～780nm) • Accuracy of wavelength: ±0.2nm • Repeatability of wavelength: ±0.1nm • Accuracy of chromaticity coordinate: ±0.0003(under standard illuminate A) • Spectrum sample interval: 5nm(Special order:1nm) • Luminosity linearity: 0.3% • Accuracy of luminosity: 1 class • Correlated color temperature measure range: 1500K～25000K • Accuracy of CCT: ±0.3%(under standard illuminate A) • Accuracy of rending index: ±(0.3%rd±0.3) • Environment temperature measure range: -10℃～80℃ • Temperature measure range(In sphere): -10℃～100℃
-
product
Remote Sensors
The most versatile and popular sensors we make. The ROS-W (Remote Optical Sensor with tinned wire termination) and ROS-P (Remote Optical Sensor with 1/8" phone plug termination) are threaded stainless steel remote optical sensors with a visible red LED light source. All these sensors have the "on-target" green LED indicator
-
product
Fiber light source
UV irradiation UV curing, infrared irradiation Thermal curing is possible with one unit. All-round player suitable for R & D · mass production line
-
product
OD And Light Transmittance Meter
Shenzhen Linshang Technology Co., Ltd.
A series of light transmittance testing instruments provided by Linshang Technology include a light transmittance meter LS116 with a parallel light path design, a optical densitometer LS117 with a diffuse transmission principle, and a split type light transmittance meter LS110 that measures the car front windshield. The light sources used in these light transmittance meters comply with the CIE photopic luminosity function.
-
product
Laser Source
TW3111
Techwin(China) Industry Co., Ltd
Laser Source TW3111 is a handheld optical light source, newly released in 2007. It can provide 1 to 6 wavelengths output to satisfy specific requirements including the 650nm visible light source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer's needs. Together with the TW3211 optical power meter, it is a perfect solution for fiber optic network applications.
-
product
Outdoor Infrared Motion Sensor
ENVIROMUX-IMD-O
Outdoor weatherproof - high reliability against water and insects. Double conductive shielding to eliminate false alarms from light sources. Registers movement in the area covered: 40 ft (12 m) x 50 ft (15 m) - 120° wide. LED lights during detection. Selectable detection paterns: Multi-Level (40 zones) or Pet Alley (18 zones). Unwanted detection areas can be eliminated using the included area masking strips. Selectable Sensitivity: High, Mid and Low. Adjustable to the brightness of surrounding environment with the Day/Night Mode switch. Tamper switch opens when cover is removed. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: -4 to 122°F (-20 to 50°C). IP54 compliant. Powered by ENVIROMUX-2D/5D/16D.
-
product
Loss Meter
L2000
3-in-1 as loss meter, light source, and power meter As loss meter Measure fiber loss at 1310nm and 1550nm As light source Single-head selectable output wavelength of 1310 or 1550 nm Ultra high output stability 0.05dB High output power preset at 0 dBm, or at customer-defined value Selectable CW, 270 Hz, 1KHz or 2KHz modulated output As power meter Calibrated outputs at 850, 1310, 1490, 1550, and 1625nm Data storage, logging, and PC up-loading Interactive measurements via PC Calibration on-site with customer's own standard if needed Selection of relative/absolute power measurement Display measurement in dB, dBm, mW, uW, nW Resolution 0.01dB; absolute accuracy 0.25dB For both single-mode and multi-mode optical fiber Small size, easy for field applications Light weight, less than 0.2Kg Auto power shut-off Enable / Disable Auto laser shut off at above 60oC Rechargeable battery, Battery-full and Battery-low indicator Changeable receptacle connector FC, SC, ST
-
product
Fourier Transform Optical Spectrum Analyzer, 350 - 1100 nm
OSA201C
Thorlabs' Optical Spectrum Analyzers (OSAs) perform highly accurate spectral measurements. Compatible with fiber-coupled and free-space light sources, these compact benchtop instruments suit a wide variety of applications, such as analyzing the spectrum of a telecom signal, resolving the Fabry-Perot modes of a gain chip, and identifying gas absorption lines. Many commonly available OSAs use grating-based monochromators, which have slow acquisition times due to the need to mechanically scan the grating and average out noise at each wavelength. Thorlabs' OSAs acquire the spectrum via a Fourier transform using a scanning Michelson interferometer in a push/pull configuration. This approach dramatically improves the acquisition time, enables a high-precision wavelength meter mode with 7 significant figures and ±1 part-per-million accuracy, and allows the included software to provide robust statistical analysis of the acquired spectra, as explained in the Design tab.
-
product
Light source
UVM-MP
Measurement of maximum of 6 points is possible. By use of thee sensor amplifier box, distance between the light receiving inlet and the controller can be extended to 10 meters. Measurement start signals can be independently output by remote control. This is useful for the light source fixtures integrating shutter mechanism.
-
product
Color Tests
LED-Check
LEDs are the standard light source in car cockpits. It is not sufficient to find out if a LED shines, or not. The LED needs to have precisely the specified brightness and color to fulfil its function.The FiberVision LED-Check system tests up to 250 LEDs in less than one second.
-
product
Monochromator-H With Integrated Halogen Lamp
We have combined our proven Monochromator-F with a halogen lamp to realize a compact tunable light source for the wavelength range 340 – 2000nm, the Monochromator-H. The very smooth and consistent spectrum of a halogen lamp makes it the ideal solution when monochromatic light with a freely selectable wavelength in the UV, VIS and NIR is needed.
-
product
Pulsed Fiber Amplifier
MOPA
These light sources are compact Master Oscillator - Power Amplifier (MOPA) structures that can be directly modulated in a defined operating range of repetition frequency and pulse power. The standard products operate in the wavelength range around 1.5 µm at a repetition frequency > 6 kHz and a pulse energy of 10 µJ/50 ns (200 W peak power).
-
product
Mid-Range Gas Filter Correlation Carbon Monoxide Analyzer
Model T300M
The Model T300M CO analyzer measures low to mid ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.The energy loss through the sample cell is compared with the span reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance from low to high range.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300M comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
SFIM-400 Spectral Flickering Irradiance Meter
Hangzhou Everfine Photo-E-Info Co., LTD
The SFIEM-400 integrates the functions of spectral measurement and flicker analysis, and uses the international patent design as the core to achieve high precision and high sensitivity measurement. Dedicated to the measurement of parameters such as light source, fast luminosity curve, flicker, flicker index, percent flicker, etc. One-click operation, one step to complete the field measurement and analysis, data real-time reading.
-
product
Square Lenticular Pulsed Backlight
ViTech B108
Lensed illumination is intended for pulsed illumination of objects in machine vision systems, in which it is not possible to mount an additional light source close to the object or where it is necessary to create the required glow intensity in a certain area. A distinctive feature of the B108 modules is the absence of persistence (except for the version with white LEDs).
-
product
MEMS Optical Sensor Test
For optical sensor test Cohu offers a variety of solutions being driven by requirements for tri-temp, parallelism and stimulus spacing. Customized optical stimulus units are integrated into Cohu’s test handling systems. For light detector test, we implement different types of light sources, such as infrared, ambient- and colored light. We offer different solutions for 3D image sensors combining emitter and receiver tests of LiDAR, Time of Flight and Structured Light devices.
-
product
Industrial Gas Analytical Instruments
Foshan Analytical Instrument Co, Ltd.
Single light source with good stability.Linear output with good reliability.Convenient to operate and maintain.
-
product
Photoelectric Detector
LG-930
The LG-900 series detectors are reflection type optical (LG-916) and photoelectric detectors developed for medium distance detection applications. The LG-916 adopts glass fiber at the tip end and can be protective enough against the external turbulent light because of pulse modulation system as the light projection source. The LG-930 also uses a pulse-lighting method, it is practically unaffected by disturbance light, furthermore, featuring a hybrid structure with the all light-projecting, light-receiving, amplifying, and waveform-shaping sections built into the unit to offer a compact design with easy-to-operate functions. By simply attaching the reflection mark to a rotating object, the detectors can detect the rotation of the object without actually touching the object.
-
product
Monochromatic High Power LED Light Sources
LS-HP1 Series
The LS-HP1 is a series of high-power, high brightness light sources for liquid light guides (LLG). It is characterized by its outstanding luminance and thus delivers very high light output from liquid light guides. The LS-HP1 works with the latest generation of high-power LEDs with up to 100W power from an area of less than 15mm². With the LS-HP1 series, we achieve the highest luminance levels through optimized optical coupling into the liquid light guide without heating it up too much. The LS-HP1 is available for liquid light guides with core diameters of 3 or 5mm.
-
product
Multi-Wavelength Foresnic LED Light Source
HandScope LED
The only LED unit that changes and selects wavelengths like a forensic light source.
-
product
PD Calibrator
PDCAL has excellent pulse-with stability; scale calibration factors are permanently stored inside its flash memory. Thanks to on board photo coupler PDCAL output pulse can be synchronized with the actual line frequency through external surrounding electrical light source systems.
-
product
Laser Source
TW3108
Techwin(China) Industry Co., Ltd
Laser Source TW3108 is designed specially aim at users with high requirements. With featuers of durable structure, large LCD display with backlight and friendly operation interface, the TW3108 advanced stability handheld optical light source provides a lot of convenience for your field work. High stability of output power and quite stable output wavelength, it is an ideal instrument for optical network installation, trouble shooting, maintenance and other optical fiber related systems.
-
product
SpectralLED® Tunable Light Sources
The award-winning SpectralLED® family of uniform intensity tunable light sources are designed to deliver unmatched resolution and accuracy. These adjustable wavelength LED light sources also have an operating lifetime and cost of ownership that cannot be duplicated with traditional light sources such as Tungsten-Halogen and Xenon lamps. With a fully spectrally tunable output, all you need is one SpectralLED to generate any arbitrary spectral power distribution, whether it be blackbody, daylight, fluorescent, LED, or something completely unique. By sweeping through individual LED channels, the SpectralLED can even emulate a traditional monochromator light source, with no moving parts and no halogen input illumination.
-
product
UV Energy Meters
Shenzhen Linshang Technology Co., Ltd.
As an UV integrator supplier providing a fair price of UV energy meter for LED, mercury vapor lamp, curing and UV exposure machine, Linshang has developed four different models of UV energy meters. According to the type of ultraviolet light source measured, the instruments can be divided into two categories, LS120, LS130 and LS132 for testing the energy and intensity of high-pressure mercury lamps, LS128, LS131 and LS133 for testing UV LED.
-
product
VP Power Meter
UVP-365
This is the standard measurement instrument to measure absolute UV vaiue. All SAN-EI's UV light source fixtures are measured by this meter.
-
product
Multi-Function Test & Measurement System
Optoplex’s Multifunction Test and Measurement System (TM100 Series) is designed to provide a flexible and cost effective optical test and measurement solution, particularly for manufacturing lines. The mainframe can be mounted in 19” rack or stationed on desk-top for ease of use. There are many selections of the pluggable modules, from tunable laser, optical spectrum analyzer, EDFA, power meter, ASE light source, optical tunable filter, optical performance monitor, …, etc.
-
product
Incoherent Sources
Our Incoherent Sources include unmounted LEDs, mounted LEDs, collimated LEDs, LED light sources, superluminescent diodes, and broadband light sources. Our collimated LEDs are particularly popular and are compatible with many microscopes. Versions are available with center wavelengths from the UV into the NIR or that emit white light.
-
product
START-1000 Start/run Up Time Test System
Hangzhou Everfine Photo-E-Info Co., LTD
Start-1000 can be used to record the start rise time and waveform of the light source in real time, and according to the design requirements of the EU directive 1194/2012, Energy Star and the international standard IEC60969, etc., it is specially used for LED lights, lamps and energy-saving lamps. And it can also be used to measure the photometry parameters of stable light sources.
