-
product
Fanless Edge AI System With NVIDIA® JETSON™ Xavier NX SoM, 1 HDMI, 1 GbE LAN, 1 GbE PoE And 2 USB
AIE100-903-FL-NX
*NVIDIA® Jetson™ Xavier NX with Volta™ architecture with 384 NVIDIA CUDA® cores*High AI computing performance for GPU-accelerated processing*Ideal for edge AI smart city applications*Supports one 15W GbE PoE for camera*Wide operating temperature from -30°C to +50°C*JetPack supported
-
product
80 Channel Relay Switch
DP-VXI-4503
DP-VXI-4503 is a 80 channel, one Form C (SPDT) relay switch designed as a C size VXI module. This high density switch module is designed with a register based interface occupying only one VXI slot. This module uses two Form ‘C’ relay switches. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose.The user can write the command for the selected channels on to the primary latch of the FPGA section. Readback is available to confirm the selected commands. On command, the data from the primary latch is transferred to the secondary latch. The relay driver section provides the necessary drive to switch ON the relays. The buffers in this section drive the relay coils.This module features a back plane trigger for VXI triggered operation. On receipt of the back plane trigger the programmed relays will be energised/de-energised. Alternatively, software trigger can be used.
-
product
LCR Meter
ST5C Colibri
*Built-in direct LCR probe*Convenient one-hand operation*Ideal for Surface Mount Devices*Automated component identification*Automated test range selection*Manual C, R, L and ESR modes*Manual test frequency overrides*Test signal level 0.5 Vrms*Portable and ergonomic design*OLED Display*Built-in Li-Ion battery
-
product
10 Digit Rate/Batch Counter
CS2-MC
The CS2-MC provides dual input(A/B phase) and display with high speed, counting, control and communication (Modbus RTU mode) of Pulse from encoder, proximity switch, photo switch or flow meter for counting, length and position control. There are 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue, and RS485 port available.The relays are also support N, C, R, E mode and Hi/Lo energized for batch / totalizer and position control.
-
product
Sound Level Meter
3M SE-402 | VP 185057
Maschinenbau Haldenwang GmbH & Co. KG.
The 3M SE-402 of quality class 2 is the ideal sound level measuring device for almost every acoustical environment. The frequency weighting can be done according to the characteristics A, C and Z and the time weighting can be set to 'Fast' or 'Slow'. Ergonomically arranged buttons and the clear digital display (resolution 0.1 dB) ensure a high level of user-friendliness.
-
product
Airborne Receivers & Bit Synchronizers
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
product
NI-9220, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle
865685-01
NI-9220, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9220, cDAQ-9171, and cRIO-9940 includes the NI-9220 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the cRIO-9940 Backshell for strain relief and operator protection from high-voltage signals. The included NI-9220 features 16 channels and 16 simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. Additionally, you can use the NI-9220 to generate 3.2 MB/s of data at the maximum sampling rate.
-
product
Potentiometer, Level Transmitter, Position Transmitter
Model TWP / TWP2
Kusam Electrical Industries Limited
• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• High Accuracy 0.1% RO at 23 ° C - 5 °C• Input / Output User Selectable• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 1.5KV/Min, between Input / Output / Power)
-
product
Probe Station
EPS1000
Reasonable price and compact design. - Sellectable chuck size : 4inch, 6inch, 8inch when ordering probe station. - Hot chuck can be installed. Temp range: RT ~ 300°C - Hot and cool chuck from 0 °C ~ 300 °C can be provided. - Maximum pcs of manipulators can be installed on the base unit of probe
-
product
CT Series Infrared Thermometer
The pyrometers of the optris CT series are equipped with one of the world’s smallest infrared sensing head with a high optical resolution of up to 75:1. The separate control box offers a high variability due to selectable analog outputs as well as several digital interfaces. The CT sensors have unique advantages for the installation in applications with high surrounding temperatures, such as within the metal, ceramics or glass industry. The robust and ambitious design allows the sensing heads to be used for temperatures up to 250°C without additional cooling. This advantage helps to reduce the costs for mechanical installations. The variety of different available spectral ranges makes the CT the ideal sensor for manifold application fields.
-
product
Voltage Controlled Oscillators
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
product
DC/AC Inverter 450 W
ODS-750-7271
DC/AC inverter with 450 W from Premium | input ranges 9.5 - 15 VDC | output 230 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke
-
product
pH Tester
148
The Elcometer 148 sensor has automatic temperature compensation, ensuring like-for-like measurements can be taken for meaningful comparison of the results.Simultaneously displays pH and temperatureMeasurement hold / freeze functionRecord maximum and minimum readings over a series of tests°C / °F user switchableWaterproof to IP57 and floats on waterAuto power off
-
product
Digital Multimeters
Multi-Display : Primary 80000, Secondary 80000, Bargraph 23 SegmentsBasic DC Accuracy : 0.05% mV Impedence : > 1000M OhmMore than 50 Measuring FunctionsFrequency Measurement : 0.5Hz to 8.0000MHz 16 Frequency Points, 1% to 99% Duty. Selectable Square Wave OutputAnalyzing Component of Current or Voltage SignalResistance : 0.1Ω to 80MΩ, 10MΩ to 8000MΩCapacitance : 1nF to 100µFTemperature : -50°C to 1372°C, -58°F to 2502°F dBm 20 Types of Reference ImpedenceAuto Data Hold / Peak HoldRelative Measurement36 Hours Dynamic Recording : MAX / MIN / AVG/ MAX-MINCommunication : Isolated Optical RS-232Timer for MeasurementBacklight DisplayAuto Power Off
-
product
EN 50155 Ethernet Switch
Axiomtek's EN 50155 certified Ethernet switches (TEN series) are designed for rail and metro systems. The TEN series is designed with IP54 enclosure and M12 connectors for protection against dust and water and supports an extended operating temperature range from -40°C to 75°C.
-
product
Vehicle Multiprotocol Interface Module
C Series
C Series Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑Rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
Reference Temperature Calibrator
JOFRA™ RTC-187
AMETEK Sensors, Test & Calibration
RTC-187 provides high-quality temperature measurement from -45 to 180°C. The 180°C is a 25° expansion over the range of the RTC-157, and it’s now the hottest temperature available for a calibrator that also supplies cold temperatures.
-
product
Aircraft Hygrometer
1011C
Buck Research Instruments, LLC
The 1011C Aircraft Hygrometer is a complete chilled mirror optical dew point system for monitoring atmospheric dew and frost points. It provides three stages of thermoelectric cooling, and can reach frost points as low as -60 to -90 C, depending on mounting configuration and operating conditions. No auxiliary coolants are required.
-
product
NI-9265, 4-Channel C Series Current Output Module
779334-01
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing … outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
product
NI-9266, 8-Channel C Series Current Output Module
785047-01
8-Channel C Series Current Output Module - The NI‑9266 is ideal for interfacing and controlling industrial current-driven actuators. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9266 includes channel‑to‑earth ground isolation for safety and noise immunity.
-
product
Mechanical Replacement Oscillator
MRO Series 3.05” x 2.02” x 1.62”
*Connectorized Package *Replaces Oscillators in Microwave Radios *Serially-Programmable *Manually Fine-Tuned *High Stability, <±1ppm (-10°C to +70°C) *Non-Volatile Memory
-
product
DC/DC Converter 2 W
REM2-3.312D
DC/DC converter 2 W from Recom | input ranges 3 - 3.6 VDC | outputs +/-12 V | operates in ambient temperature from -40 to +95 °C
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 2m, HV
40-972-037-2m-MU-HV
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
USHIO Red Laser Diodes (633nm - 690nm)
The Optoelectronics Company Ltd
Features: 5.6 mm CAN package, Optical output power: 80 mW (CW), 300 mW (pulsed – pulse width: 10 ns, duty: 10%), Lasing wavelength: 658 nm, Wall-plug efficiency*: 33%, Operating temperature: -10° – +60° C (CW); -10° – +75° C (pulsed), Single transverse mode, TE mode oscillation, MTTF >10,000 hours
-
product
Imaging
SLA64 (Preliminary)
A 1 x 64 element silicon-based thermopile array. Each active area is 0.45mm x 2.0mm with a time constant of 42ms and a low Temperature Coefficient of Responsivity of -0.06%/C. It is packaged in a 68-pin QIP. Includes internal 30k 5% NTC chip thermistor provides ambient package temperature measurement. See Thermistor Options p/n: MT04.
-
product
Handheld Instruments for Measuring Humidity & Temperature
Our range of handheld instruments are perfect for monitoring environmental conditions. Models with an interchangeable probe input have the wide measurement ranges -100…200 °C, 0…100 %rh with a Rotronic probe selected for the application.
-
product
NI-9866, 1-Port C Series LIN Interface Module
781963-01
1-Port C Series LIN Interface Module—The NI‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The NI‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis.
-
product
Keysight 32-Channel FormC/Form A General Purpose Switch for 34980A
34937A
The Keysight 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 60W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
product
64 Input USB Modular Digital I/O
U2652A
The Keysight U2652A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
product
32-CH Sinking Type Digital Ouput EtherCAT Module
EPS-2132
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.





























