Process Monitoring
-
Product
Phase Monitors
-
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Pt RTD Temperature Monitor
SIM923
-
Stanford Research Systems, Inc.
The four channels in the SIM923 have independent, stable 1 mA current sources to provide sensor excitation. Sensor resistance is determined ratiometrically with a half-bridge circuit consisting of the sensor and an internal reference resistor.
-
-
Product
C/Ku Band Satellite Monitoring
SCL-3412
-
C/Ku Satellite Monitoring System (SCL-3412) is designed to intercept International/national telecom carriers, GSM A/Abis links and IP Carriers over satellite which are using C, Ku, X or Ka-Band. In order to reduce the manual effort and time consumed in the analysis of the carriers, system is integrated with Satellite Carrier Analysis module, which automatically performs the scanning on the selected spectrum and provide the list of carriers along with their payload type (i.e DCME, GSM or IP) and characteristics parameters. This provides great help to take decision for monitoring of the carriers of interest.
-
Product
Real-Time Monitor Recorders
RTM – Real-Time Quality Monitoring
-
for ST 2110 Networks with 10G IP Interfaces
-
Product
Monitoring & Simulation
-
ETAP Power System Monitoring & Simulation (PSMS) is at the heart of the ETAP Real-Time power management system. Power System Monitoring & Simulation is the smart choice for both small and large electrical utility systems, generation plants, industrial sites, manufacturing facilities, and off-shore oil platforms.
-
Product
Dual Wide Range Power Monitor
LTC2992
-
The LTC®2992 is a rail-to-rail system monitor that measures current, voltage, and power of two supplies. It features an operating range of 2.7V to 100V and includes a shunt regulator for supplies above 100V. The voltage measurement range of 0V to 100V is independent of the input supply. Two ADCs simultaneously measure each supply’s current. A third ADC monitors the input voltages and four auxiliary external voltages. Each supply’s current and power is added for total system consumption. Minimum and maximum values are stored and an overrange alert with programmable thresholds minimizes the need for software polling. Data is reported via a standard I2C interface. Shutdown mode reduces current consumption to 25μA typically.
-
Product
PDS Pile Placement Monitoring Software
-
The Monopile Placement module is the result of the cooperation between our clients and our engineering and software teams.Monopiles are used in wind farms as a foundation upon which to place a wind turbine generator. The application monitors the process of the placement of the monopoles.
-
Product
Central Visibility and Remote Monitoring
Torque Visor
-
Visor provides central visibility and remote monitoring of multiple probes, plus easy access to a comprehensive log of system events. Operators can retrieve detailed analysis directly on the respective probe, and spot fault trends across services or several geographic regions.
-
Product
RF Power Monitors
-
Standard connectors: RF In / Out - N-Female, UHF optional. Sampling Ports - RCA-Female, BNC optional.
-
Product
Vibration Monitors
-
Monitor vibration with these full-featured modules, available in portable and standard formats.
-
Product
Target Tracking/Image Processing
-
Our automatic video trackers and image processors are at the heart of a wide range of commercial, military and paramilitary systems where they provide the highest performance solutions in the smallest, fully environmentally proven hardware packages.
-
Product
Process temperature meter
PCE-IR 6
-
Electronic Product Test & Design
Its infrared sensor has an optical resolution of 50:1 and accurately measures temperatures from a distance. The infrared temperature meter is equipped with various relays that enable an alarm to be triggered and makes a cooling or heating control possible.The measurement range is -50 ... 900 ° C, with a resolution of 0.1 °C. The emissivity of the infrared temperature meter can be freely set, which makes the pyrometer PCE-IR 6 useful for a variety of surfaces in safety engineering, plastics processing and steel processing.
-
Product
Battery Monitoring System
-
JUNXY Battery Monitoring Systems are designed in accordance with IEEE Battery Maintenance recommendations. This allows you to maintain a safe and secure system with Real-time monitoring, which will minimize the probability of a failure and optimize the service life of the battery. JUNXY Battery Monitoring Systems not only monitor the batteries, but also the external parameters which could affect the performance of the system, providing added security. It is a powerful tool for mitigating and preventing costly downtime due to unexpected system failure.
-
Product
3 1/2 Digital Process Meter
CSN Series
-
CSN Series 3 1/2 Digital Process Meter is a simple type of economic Panel Meter, and its large LED display with 20.0mm and anti-jamming design, quality, reliable, easy to install.Full range can be specified DC voltage / current, thermal resistance , load cell, potentiometer , Resistance and pulse signals such as the general measurement requirements.
-
Product
TDL Processing Solutions
-
Curtiss-Wright Defense Solutions
We simplify tactical data link (TDL) communication with standards-based solutions that are designed to improve tactical communications. Our solutions reduce the time, risk, and expense of TDL implementation and integration, alleviate interoperability issues, and lower lifecycle maintenance costs for militaries and prime contractors worldwide.
-
Product
Battery Monitoring Systems
-
Franklin Electric - Grid Solutions
Combines wireless communication with patented, field-proven battery conductance analysis technology. It lowers total cost of ownership while providing the most thorough and easy to access stationary battery health diagnostics.
-
Product
Portable Multi-channel Waveform Monitoring Recorder
MR1200 Series
-
The portable waveform monitoring recorder is a device for recording and analyzing the change process of electrical signal related parameters of the power system.
-
Product
Piezobalance Dust Monitor
3520 Series
-
The Kanomax Piezobalance Dust Monitor 3521/3522 is a unique respirable aerosol monitor, providing direct mass concentration of particulates using PIEZOBALANCE technology; ideal especially for oil mist monitoring. The Kanomax 3521 is equipped with 4 and 10µm impactors while the 3522 is equipped with a 2.5µm impactor. Unlike conventional dust meters, which count particles, a piezobalance dust meter like the 3521 or 3522 “weighs” mass concentration of particulates.
-
Product
Translating process images into significant tool-defect reduction
Trans-Imager
-
Real-time, tool-specific defectivity data. Now there is a way to monitor defectivity on individual processing tools – automatically – in real-time. Microtronic’s new Trans-Imager software module is able to take high-resolution images directly from your processing equipment and immediately detect and displaymacro wafer defects – transferring all of that information into our powerful and long-proven ProcessGuard software which provides a wealth of defect management and analysis. This new capability is called ProcessGuard Xtensis (PGX) because it extends the power of ProcessGuard software to fab tools that previously had no way to detect defects. This provides an important new stream of defect data.
-
-
Product
DRX Aerosol Monitor
8534
-
Real-time dust monitoring takes a giant leap forward! Only the DUSTTRAK™ DRX Aerosol Monitor 8534 can simultaneously measure both mass and size fraction - no other monitor can do both. The DUSTTRAK DRX handheld monitor is a battery operated, data-logging, light-scattering laser photometers that gives you real-time aerosol mass readings. It uses a sheath air system that isolates the aerosol in the optics chamber to keep the optics clean for improved reliability and low maintenance.
-
Product
Leakage Current Monitor
LCM500
-
The Doble LCM500 Leakage Current Monitor can measure condition while a surge arrester is still in service, measuring the quality of the metal oxide blocks and helping manage the risk of failure.
-
Product
Infrared Video Processing
-
*Edge Enhancement improves the apparent sharpness of an image by boosting the contrast of edges in the imagery *Electronic Image Stabilization compensates for jitter in a video sequence, providing stabilized video output and remaining responsive to intentional user panning*Auto-Focus automatically adjusts the lens focus to its optimal in-focus position *Electronic Zoom uses interpolation to produce an enlarged image on the video display *Non-Uniformity Correction compensates for detector-to-detector non-uniformity to provide a well-calibrated image output
-
Product
Multi Wavelength Monitor
LV5490/LV5480
-
The LV 5490 is a multi waveform monitor that supports 4K video format (4096×2160、3840×2160) based on 3G-SDI dual link or quad link, HD-SDI quad link, and 12G-SDI. The following two 4K video division transmission systems are supported. ・2-SAMPLE INTERLEAVE DIVISION ・SQUARE DIVISION
-
Product
Level Monitoring
-
Magnetic level switches are used for the monitoring and control of liquid level in tanks. These level switches are specifically manufactured to customer specifications. The float switches are manufactured with a hermetically sealed contact which is located within the guide tube. The float sliding on the tube contains a ring magnet which activates the sealed contact in a non-contacting fashion. The sealed contacts are available as SPST (N/O or N/C) or SPDT (N/O + N/C). The float sliding up and down on the guide tube is the only moving part on the M-series magnetic float switches.
-
Product
Non Contact River Monitoring System
RiverSonde®
-
The RiverSonde® is an affordable, non-contact monitoring system providing continuous surface cross-channel velocity profiles for streams, channels, and rivers. Data output from this system can be used as an index velocity in conjunction with other data sets or as model input for calculation of total water discharge (Q). It is also ideal for monitoring river movement during flood events and in disaster planning.
-
Product
CMP Process and Material Characterization System
CP-4
-
he new Bruker CP-4 CMP Process and Material Characterization System has been designed from the ground up specifically for reliable, flexible, and cost effective characterization of wafer polishing processes. Reproduces full-scale wafer polishing-process conditions. Provides unmatched measurement repeatability and detail. Performs tests on small coupons rather than whole wafers for substantial cost savings.
-
Product
Remote Monitoring & Lubrication
-
Remote Monitoring and Lubrication Products remove the guesswork from your maintenance practices so you stay in control of your equipment’s health
