Strain Gage Signal Conditioners
See Also: Strain Gages, Strain Gauges, Strain Gage Amplifiers
-
Product
"Signal Transporter"
LTX-5520
-
The LTX-5520 enables the conveyance of sixteen independent channels of digital information over fibre optic links ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled at 50 mega-samples per second, multiplexed and transmitted serially over an optical fibre at a 1 Gb/s data rate.
-
Product
Acquisition Of Strain Gauges, Isolated, 18-bit
APCI-3300-8
-
18-bit resolution, unipolar, 16-bit accuracy 8 differential inputs for strain gauges Voltage range 0 to + 2.5 V 8 independant voltage sources for the connected pressure sensors Output voltage for the voltage sources 5 V, 40 mA Gain and offset calibration Calculation of the pressure value through software Programmable gain 16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz 4 digital input channels, 24 V and 3 digital output channels, Open Collector, isolated
-
Product
PXIe Performance Vector Signal Analyzer: 50 GHz
M9393A
-
9 kHz to 8.4 GHz, 14 GHz, 18 GHz, or 27 GHz Frequency extension to 50 GHz (minimum frequency of 3.6 GHz) with Option FRX40 MHz (standard), 100 MHz, or 160 MHz analysis bandwidth, and optional wideband IF output with Option WB1Up to 4 time-synchronous channels
-
Product
16-Channel RTD Signal Conditioning Card
ProDAQ 5821
-
The ProDAQ 5821 series of Signal Conditioning Cards is designed to interface with a variety of sensors, principally RTDs, Thermistors, Cryogenic Diodes and Voltage type sensors. Each version of the 5821 provides the capability of precise 4-wire measurement. In order to achieve this, a precise 500μA constant current source is provided per channel. The current source can be disabled on a per channel basis and is monitored to ensure that current is flowing. The value of the output current is stored on-board after calibration. In order to achieve the highest accuracy the output current may be automatically calibrated 'on-the-fly' using the ProDAQ 3416 24-bit Sigma-Delta ADC card and an on-board precision resistor.
-
Product
PWM TO VOLTAGE SIGNAL CONVERTER
RCPWM2V
-
The RCPWM2V is a device that converts a standard hobby RC signal (1-2ms pulse) into a proportional analog voltage (0-5V). In many electronics applications the main processor is constantly busy and does not have the ability to address the time-sensitive PWM signal from an RC receiver immediately. This results in signal distortion or a sluggish response due to the extra filtering required. The RCPWM2V provides a simple solution by converting the signal into an analog signal. The main processor can then read the signal whenever it has time.
-
Product
PXI Signal Conditioning
-
For RF and Microwave measurements, Keysight PXI signal conditioning modules modify an analog signal to meet the requirements of the next stage for signal processing. Signal conditioning examples include amplification, attenuation, converting and filtering.
-
Product
Signal, Patchcord, Receiver, 72", QuadraPaddle, 22 AWG White, Twisted Pair ( 5 Amps)
7-124439000-072
-
Signal, Patchcord, Receiver, 72", QuadraPaddle, 22 AWG White, Twisted Pair ( 5 Amps)
-
Product
Signal Analysis
Harmonic Distortion Analysis
-
The software is used for automatic measurement of the harmonic distortion factor and voltage r.m.s. of signals coming to the input channels of FFT spectrum analyzers. Adjustment to the frequency of the main component is performed automatically. The program is based on the measurement of the voltage r.m.s. of higher components by an external or internal reference signal.
-
Product
Speaker & Signal Analyzer
-
Specifications*frequency available for models:1-300/450/600MHz *frequency sweep mode:full sweep, narrow sweep,spot frequnecy
-
Product
Signal Analysis Synthetic Instrument
SASI
-
Textron Systems’ SASI 240 is a Signal Analysis Synthetic Instrument that combines the capabilities of six distinct measurement systems into a single device. Our dual-channel architecture enables two independent radio frequency (RF) measurements to be run simultaneously. Whether used as a benchtop device or an integrated automated test equipment (ATE) RF subsystem, our SASI’s simple and intuitive graphical user interface (GUI) ensures easy, out-of-the box functionality.
-
Product
Signal Amplifier
A10150
-
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
-
Product
PIR Sensor With LED Signal
555-28027
-
The PIR Sensor detects motion by measuring changes in the infrared (heat) levels emitted by surrounding objects. When motion is detected a LED lights up the lens dome as a visual signal, and the module also outputs a high signal on its output pin.
-
Product
Signal Analysis
FFT Analysis
-
The program FFT (Fast Fourier Transform) Analysis is used for narrow-band spectral processing of signals coming from the input channels of ADC modules and FFT spectrum analyzers (in real-time or recorded time realization view mode), as well as for viewing various spectral characteristics of signals.
-
Product
Video Signal Distributor
MSHM-305A/310A
-
MSHM-305A/310A, HDMI Distribution,Amplifier, distribute three digital video input sources to the five (or ten) output channels. The built in amplification function enables HDMI signal distribution without signal loss. The product guarantees to support full channels HDMI/HDCP compliance. User can select one input source of the three and make sure connected condition with led of the front panel.
-
Product
Optical Signal Transmission
Analog
-
Used for oscillographing analog signals under EFT/EDS/RF interference.
-
Product
PSG RF Analog Signal Generator, 100 kHz to 9 GHz
E8663D
-
Tackle demanding radar & satcom measurements with metrology-grade performance, including high output power & superior level accuracyUse as an ideal reference in phase noise test systems or for analog-to-digital converter testing with the lowest phase noise in a commercial sourceCharacterize devices & circuits by adding AM, FM, M & pulse modulation to your signalImprove existing test system performance: E8663D is built on the outstanding legacy of the 8663A & is fully code compatible
-
Product
Signal Generator, 20MHz, 1 Channel
33509B
-
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
Product
FPGA Signal Processor
372
-
The Model 372 is designed around the Texas InstrumentsADS42LB69 16-bit ADC and the Analog Devices AD9788DAC. The 250 MHz sample clock is supplied by either theon-board frequency synthesizer or an external source. Thefrequency synthesizer can be phase locked to the local10 MHz TCXO or an external reference can be used toachieve system-wide phase coherence.
-
Product
8-CH 24-Bit High-Resolution Dynamic Signal Acquisition Module
PXIe-9529
-
The ADLINK PXIe-9529 is a high-performance, high density, 8-CH analog input dynamic signal acquisition module. The PXIe-9529 features eight 24-bit simultaneously sampling analog input channels. The 24-bit sigma-delta ADC provides a sampling rate of 192 kS/s at high resolution, making it ideal for higher dynamic range signal measurement. All channels are sampled simultaneously and accept input range up to ??10V, and the analog inputs support software-selectable AC or DC coupling and 4 mA bias current for integrated electronic piezoelectric (IEPE) sensors. The module is especially designed to meet the requirements of vibration analysis and audio testing.
-
Product
SIGNAL GENERATOR
TG-1300
-
LOW BATTERY CONSUMPTION COMPACT SIZE DESIGN OUTPUT LEVEL ADJUSTABLE OUTPUT LEVEL DISPLAY MAX. 5BANDS(individual or Simultaneously) PORTABLE TYPE
-
-
Product
Online Audio Frequency Signal Generator
WavTones
-
We are proud to offer not only the best audio frequency signal generator on the net, but also a high-end sound generator, which compares favorably to the more expensive software and hardware tone generators!
-
Product
Optical Signal Conditioning Products
-
The single-mode fiber N7761A, N7762A and N7764A provide 1, 2 or 4 attenuation channels in a compact remote-controlled instrument. These attenuators provide very fast adjustment and have built-in output power monitoring for accurate power setting and control, as needed for receiver sensitivity testing or in system simulations.
-
Product
Vector Signal Generator
VSG25A
-
The VSG25A is a 100 MHz to 2.5 GHz vector signal generator, featuring a 12-bit I/Q baseband arbitrary waveform generator which can be clocked at virtually any frequency from 54 kHz to 180 MHz, and includes a 4096×16 bit pattern buffer for built-in or custom modulation.
-
Product
Digital Signal Processing (DSP)
-
Digital signal processing (DSP) affords greater flexibility, higher performance (in terms of attenuation and selectivity), better time and environment stability, and lower equipment production costs than traditional analog techniques. Components available today let DSP extend from baseband to intermediate frequencies (IFs). This makes DSP useful for tuning and signal selectivity, and frequency up and down conversion.
-
Product
PSG Signal Generators
-
Generate trusted microwave signals: get metrology-grade frequency & level accuracy with excellent distortion & spurious characteristicsRely on the highest quality signals from pure CW tones with 1 W of power to complex, vector-modulated signals with 4 GHz bandwidthReduce the time you spend on signal creation with Signal Studio softwareTake advantage of increased performance, flexibility & speed when you replace a legacy source with the code-compatible PSG
-
Product
Signal Generator
-
This signal generator is a powerful tool in audio equipment analysis. Together with the analyzer "WinaudioMLS" a rich set of measurements can be performed. This generator is available in a freeware version and a PRO version.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
PCI Bus Signal Amplifier
3322
-
Model 3322 is a 3U single-slot, PCI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3322 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
Product
PXI Strain Gauge Simulators & Pressure Transducer Simulators
-
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
