Bare Board
is a printed wire board only.
See Also: Bare Board Probes, Bare Board Testers, Bare board Fixtures
-
Product
RTM Actuator Signal Conditioning Board
MS 3630I
-
CPCI Rear IO Actuator Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on Primary and Secondary actuator interface. This card shall handle excitation signals, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
Product
Digital CMOS board level camera
C13949-50U
-
The core of the C13949-50U camera is the scientific image sensor, an The core of the C13949-50U camera is the scientific image sensor, an advanced CMOS detector that simultaneously achieves high resolution, fast readout speeds and low noise. With its small size, board-level design and simple, low-cost integration using USB 3.0, the C13949-50U is the ideal camera for OEM scientific imaging. Resolution: 12 megapixels (4096 3008)
-
Product
Compact PCI Connector Board
cPCI-J2-SCSI
-
Ribbon cable is used between the rear IO and SCSI connector. The lengths are reasonably well matched. The cable is short. The design is intended for lower speed IO - 10 MHz and below. Above 10 Mhz there may be some attenuation.
-
Product
Meter Test Board
MTB
-
The accuracy of TESCO’s Meter Test Board (MTB-3050) is now available in multi-position test boards to perform individual or simultaneous accuracy tests in the meter shop!
-
Product
Ethernet to Relay Interface Boards
Model 8064 OEM
-
* 115631-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional terminal board for easy connections without soldering. See the Ethernet Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS Wiring Kit to connect to an RJ45 connector on the rear panel.
-
Product
Single Board Computer
VME-1910
-
Curtiss-Wright Defense Solutions
Featuring the Intel 9th Gen Xeon E “Coffee Lake Refresh” processor, the VME-1910 is a perfect replacement for legacy SBCs, bringing new life and increased performance into systems required to offer higher levels of functionality than previously deployed.
-
Product
Training Board
-
The JT 2156 training board has been devised to demonstrate all the latest features and test techniques available to users of JTAG Technologies’ ProVision & JTAG Live application development systems. As well as a modern ARM Core processor, the design also includes an Altera Cyclone FPGA, DDR Memory, Ethernet PHY, and several SPI and I2C peripheral parts. The JT2156 is shipped with a comprehensive self-study manual for getting to know the in-depth features of ProVision and/or JTAGLive Studio. For Altium users the design also serves as an example of how to adapt the Nano board into a realistic custom design.
-
Product
Breakout Boards
-
GrayStone offers a family of DIN rail mountable breakout boards in various connector to terminal block configurations suitable for use in automation panels, electronic diagnostics or other general electronic applications.
-
Product
Board Cameras
-
e-CAM & See3CAM Series of Camera Boards. e-CAM camera board is e-con's reference design featuring a board camera interfaced to a processor on its high speed CMOS interface. Board cameras are available for Jetson Developer kits and NXP i.MX6 boards. For processors, that don't have the Camera ISP pipeline, e-con Systems provides the complete software stack for raw image sensors. The software stack has a wide variety of features ranging from color correction, gamma correction, dead pixel correction, color space conversion, sharpen filter etc.
-
Product
Signal Conditioners / OEM Boards
-
Signal conditioners and OEM cards that can be integrated into your system.
-
Product
Meter Warm-up Board
3000/3001
-
The Catalog 300X Universal Meter Warm-Up Board is designed to go from the shop floor to a customer location. TESCO's Warm-Up Board is made from a high quality industrial fiberglass enclosure and is light and durable. TESCO's warm-up board is the portable, effective solution to your shop, vehicle, or remote meter warm-up needs.
-
Product
Test Extension Boards
XJIO
-
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
Product
I/O Input Board
VME-3123A
-
16-Bit High-Throughput Analog Input Board, 16 Channels with Simultaneous Sample-and-Hold Inputs
-
Product
3U Processor Board
CP32001
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP32001 is designed based on the second generation Intel® Atom™ processor and D525, D455,.The processor has the advantages of low power consumption, high performance and other characteristics and also equipped with high performance Southbridge chips: the Intel® I / O Controller Hub 82801HBM (ICH8M).CP32001 memory controller supports up to 4 GB of DDR3 memory (2x 2GB).The maximum resolution of VGA display core is 2048x1536.CP32001 is a small PC, integrates many common interfaces, for example: USB, Gigabit Ethernet. SATA II and COM, and also equipped with high-performance sound card interface.
-
Product
PCI/PCIe I/O & Comm Board
76C2
Multifunction I/O
NAI’s 76C2 is a PCI/PCIe multifunction I/O and communication board with three independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
3U Processor Board
CP32107
-
LinkedHope Intelligent Technologies Co.,Ltd.
Based on Intel® 4th Generation Core™ and Celeron® i7/i5/i3 processors, CP32107 is a high-performance 3U 8HP CPCI PlusIO SBC with up to 4x2.4GHz and 8 threads CPU. For better heat-dissipation, CP32107 is equipped with a noiseless fan that has adjustable rotational speed.CP32107 is provided with rich front and rear I/O interfaces, including 2x USB3.0 for peripheral, 2x GbE (through M12 Connector) for LAN, 1x Display Port supporting 3840x2160 output on front; 2x SATA III, 2x GbE, 4x USB2.0, 2x RS232/422/485 on rear. The rear is compliant with PlusIO Standard, and supports 3 x1 PCIe Gen2.0 interfaces. Besides, mSATA or CFast disk can be installed on CP32107.
-
Product
3U OpenVPX Multifunction I/O Board
68G5P
Multifunction I/O
The 68G5P is a 3U OpenVPX board that can be configured with up to three NAI smart I/O and communication function modules. Uniquely designed, the 68G5P provides external access via PCIe x1 and/or SATA II interfaces directly to supported NAI function modules, providing external host SBC function expansion. Additionally, the 68G5P is on NAI’s certifiable product line development roadmap supporting DO-178C and DO-254 design assurance guidelines for safety-critical applications. Ideally suited for rugged Mil-Aero applications, the 68G5P delivers off-the-shelf solutions that accelerate
-
Product
3U VPX PMC/XMC Carrier Board
IC-CMC-VPX3b
-
The IC-CMC-VPX3b is a carrier board designed to expand 3U VPX system capabilities with the integration of PMC/XMC mezzanines.
-
Product
6U OpenVPX Multi-function I/O Board
67C3
Multifunction I/O
NAI's 67C3 is a 6U OpenVPX Multi-function I/O and Communication Board with six function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
13MP Camera Board For I.MX8
E-CAM130_iMX8
-
e-CAM130_iMX8 is a 13MP 4-lane MIPI CSI-2 autofocus color camera board for iMX8 family of processors. The e-CAM130_iMX8 camera board is interfaced directly to the CSI-2 MIPI interface on the Variscite's DART-MX8M/DART-MX8M-MINI Evaluation kit (VAR-DT8McustomBoard). The iHDR (interlaced High Dynamic Range) support helps to capture good quality images in both high and low illumination. e-CAM130_iMX8 also comes with a high-performance Image Signal Processor (ISP) that performs all the Auto functions (autofocus, auto white balance, auto exposure control). Customer who wants to integrate this camera into their end product can directly purchase e-CAM130_MI1335_MOD camera module.
-
Product
Hall Sensor Board with I2C Interface
050-382
-
Version: +5V/15A +12V/15A -5V/15A -12V/15A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Advanced Programmable IO Board
MS 1508
-
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
Product
CPCI Advanced Compute And IO Board
-
Advanced Compute & IO Board is high end Microprocessor based Mixed Input & output Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have digital I/O signals, analog I/O signals, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board has high end FPGA which is used for automatic (Programmable) data acquisition and very useful high speed data acquisition. Board is based on CPCI architecture and can be used with CPCI or PXI backplane.
-
Product
TMR Switch Sensor Demo Board
-
MultiDimension Technology Co.,Ltd.
Demonstration kit for MDT omnipolar and bipolar TMR switch sensors
-
Product
3U VPX Graphics Output Board
GR2
-
The Abaco GR2 is a 3U VPX graphics output card based on NVIDIA® Pascal™ Quadro® P5000/P3000 GPUs. The GR2 offers very high performance graphics and GPGPU capability – up to 6.4 TFLOPS floating-point - with CUDA™ and OpenCL™ support.
-
Product
Single Board Computer
VPX3-131
-
Curtiss-Wright Defense Solutions
The VPX3-131 3U OpenVPX Power Architecture Single Board Computer (SBC) combines the performance and I/O capabilities of NXP's P4080 QorIQ Octal processor with an extensive I/O complement to provide a highly capable processing platform for a wide range of rugged, embedded military and aerospace applications.
-
Product
Smart GPIB Serial Interface Board
Model 4808
-
* Provides smart GPIB-to-serial path for serial devices with RS-232, RS-422 or RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Rear panel mounting eliminates cables.
-
Product
MTM Development Board Kit
-
REDUCE MTM WIRING COMPLEXITIES: The MTM Development Board Kit development and testing of embedded and high-level programs with comment MTM modules.
-
Product
Configurable PCI/PCIe Multifunction I/O Boards
Multifunction I/O
NAI offers a variety of PCI and PCIe-based Multifunction I/O boards optimized for I/O intensive sense, response and communication requirements in rugged defense, commercial aerospace, and industrial applications.
-
Product
MIL-STD-1553 Eight-Channel VME Board
VME-8-1553
-
The V-Orchestra™ is an eight channel MIL-STD-1553B board which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. V-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 32K word of internal RAM.
