-
Product
Modbus TCP Redundant Ethernet I/O
-
ICP DAS USA's RIO-9380 is a Modbus TCP based Ethernet-based Data Acquisition Rack that supports redundant communication and redundant power for maximum uptime. Our Redundancy Ethernet I/O Racks provide a scalable, open architecture that bridges factory-floor hardware with enterprise IT systems. Designed for mission-critical reliability, these racks support redundant communication paths to ensure the system remains operational during network or power fluctuations..
-
Product
WISE Modbus Data Logger
-
WISE (Web Inside, Smart Engine) are Modbus TCP based data acquisition controllers that allow for remote monitoring and logic control through a web interface. They can trigger outputs based on inputs, send email alarms and can show the status through a web page.
-
Product
Modbus Digital Input Output Modules
DAT3100 Series
-
The Datexel DAT3100 series is a range of Modbus digital input output modules. These cards or modules have the ability to accept digital voltage inputs and provide an output by the way of relays, NPN or PNP transistors. The DAT3100 devices can communicate with RS485 or RS232 on a Modbus or ASCII protocol making the DAT3100 series a very economical solution to large and small scale Data Acquisition. Combining these digital input output devices with the DAT9000 controllers and the DAT3000 analog input output modules make Datexel the smart choice where Data Acquisition is needed.
-
Product
Modbus Analog Output Modules
DAT3020 Series
-
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
Product
16-Port +2 SFP Entry-Level Switch Supporting Modbus TCP/IP
EKI-5726FI-MB
-
Entry-Level Managed Switch, Provides wide operating voltage 8.4~52.8 VDC, C1D2 and ATEX certified for horizontal area. IXM function enables fast deployment, Modbus/TCP Enabled by default, Supports X-Ring for ultra high-speed recovery time less than 20ms.
-
Product
Modbus TCP Based Dual Ethernet Port I/O Modules
-
ET-7200 Modbus TCP Based Dual Ethernet Port I/O have 2 Ethernet ports for daisy-chain networking. They are configurable over a standard web browser. Support for Modbus TCP protocol allows easy integration with SCADA software.
-
Product
Modbus Simulator & Tester
Modbus Poll
-
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
Product
WISE-71xx/WISE-72xx Modbus TCP Controllers
-
WISE (Web Inside, Smart Engine) are Modbus TCP based Data Acquisition Controllers that allow for remote monitoring and logic control through a web interface. They can trigger outputs based on inputs, send email alarms and can show the status through a web page. WISE Data Acquisition Modules can be configured through a web page to implement IF-THEN-ELSE control logic with just a few clicks; no programming is required.
-
Product
Autonomous RTUs
-
Infinite Industrial Informatics Lt
Autonomous RTUs are power network independent devices, opening up new horizons for telemetry in off-grid areas. An autonomous RTU features in measuring capabilities and contains a wireless MODEM for data and alarm transmission. It can also provide all necessary circuits for powering measuring transducers and sensors. The device is commonly powered by an internal battery and is housed in a IP66 to IP68 enclosure for outdoor use. The battery lifetime requirements extend from few months to 15 years. Another common requirement is continuous, maintenance free operation in harsh environmental conditions and extended temperature ranges.
-
Product
Modbus Transducers
THI Sensors
-
The THI-485 sensors are Modbus transducers for measuring thesurrounding temperature and relative humidity or for theacquisition of up to four passive pulse signals or digital states. This feature extends the possibilities of the device, turning it into a kind of RS485 pulse concentrator from other sensors andmeters.
-
Product
Modbus Master TCP/IP Component for .NET
WSMBT
-
WSMBT is a powerful and simple to use .Net component that makes it easy to access data from a Modbus slave device connected to the PC's Ethernet network. Simply drop the component on your form and talk to your device with your VB.NET, C# or Managed C++.
-
Product
Modbus Gateway With Ethernet for Woodward GCP-30 Genset Controls and LS 4 Controls
GCP-MG
-
GCP-MG is a next-generation Modbus/CAN gateway specifically designed to interface Woodward's GCP-30 series genset controls (GCP-31, GCP-32), and LS 4 circuit breaker controls with Modbus networks. The GCP-MG gateway has been developed in cooperation with Woodward to ensure the highest possible degree of interoperability with Woodward equipment.
-
Product
8AI Modbus RS-485 Remote I/O
ND-6117
Data Acquisition Module
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
Product
8AI/ 8DI/ 4DO/ 4-Slot IO Modbus /BACnet /101/104 /DNP3/PLC/Azure/AWS IoT RTU
ADAM-3600
-
Domain Focused Onboard IO -8AI / 8DI / 4DOHigh I/O Flexibility with 4-slot I/O ExpansionModbus & DNP3 ProtocolIEC 61131-3&C Programming LanguageOperation Temperature -40~70°CMultiple wireless options for Zigbee/ Wi-Fi/ 3G/ 4G/ GPRSHigh Performance CPU Cortex A8 600MHzLow Power DDR3L 256MB RAMEmbedded Real-time Linux Kernel
-
Product
7DI/8DO Robust Modbus RS-485 Remote I/O
ADAM-4150
-
7ch digital input(counter)/8ch digital output (pulse output)Operation temperature: -40~85°C, Power input: 10VDC~48VDCNoise protection: 4kV surge (power), 4kV EFT, 8 kV ESD protectionInterface: RS-485/USB3000VDC isolation protectionLED indicator to monitor I/O status
-
Product
PoE Modbus TCP Based Dual Ethernet Port I/O Modules
-
The PET-7200 Series are communicable over Modbus TCP, can be Powered over Ethernet (PoE) and have 2 Ethernet ports for daisy chain configuration. The built-in two-port Ethernet switch is to implement daisy-chain topology. The cabling is much easier and total costs of cable and switch are significantly reduced. They are configurable over a built-in web server and have a Web HMI.
