Gate
-
product
Low Noise Amplifiers (NF < 3 DB)
Qorvo offers a variety of transistors and amplifiers with industry-leading low noise performance. We provide multiple product solutions, ranging from discrete transistors, packaged MMIC solutions incorporating internal matching and on-chip linearization, and dual amplifiers for use as push-pull or balanced amplifier configurations. Qorvo's LNAs are manufactured using our pHEMT processes with 0.15 µm, 0.25 µm or 0.5 µm gate lengths.
-
product
Semiconductor Curve Tracer
CS-8000 Series
The CS-8000 series are equipped with a high-voltage source of up to 5 kV and a high-current source of 2 kA. It features Pulse output, Gate pattern, and very small current measurement capabilities, and it supports the design evaluation of wideband-gap semiconductors such as SiC and GaN.
-
product
Semiconductor Tester
5000E
Current Ranges:Standard: 2.0nA – 50AUp to 100A with Mainframe ExtensionVoltage Ranges:Standard (anode): 10mV – 1000V2000V with 2kV Anode OptionStandard (gate): 10mv – 20V80V with 80V Gate Option
-
product
Flaw Detector & Thickness Gauge
DFX-8+
Measurement Gates: Two independent gates (Flaw), and three gates (thickness). Start & width adjustable over full range. Amplitude 5-95%, 1% steps. Positive or negative triggering for each gate with audible and visual alarms.
-
product
Small InGaAs Camera For Short Exposures
Bobcat Gated Series
The Bobcat 320 Gated series is based on an in-house developed, temperature stabilised InGaAs detector with a 320 x 256 pixel resolution. The Bobcat 320 Gated cameras are able to provide maximum frame rates up to 400 Hz. The exposure time of the sensor is configurable from 100 ns up to 1 ms in steps of 100 ns, or from 1 ms to 40 ms.
-
product
IGBT Drive
IGBT gate drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode, signal processing circuit and power output transistor on the output side in a single chip. This coupler is designed specifically to provide high common mode transient immunity (CMR) and a high output current, and has an active miller clamp and high switching speed, making it ideal for driving IGBTs and MOS FETs.
-
product
Flaw Detector & Thickness Gauge
DFX-7+
Measurement Gates: Two independent gates (Flaw), and three gates (thickness). Start & width adjustable over full range. Amplitude 5-95%, 1% steps. Positive or negative triggering for each gate with audible and visual alarms.
-
product
Rad Hard GaN Drivers
The space market has been driving towards more efficient power management solutions. Part of the drive includes the use of Gallium Nitride Field Effect Transistors (GaN FETs) for power conversion. GaN FETs have higher power conversion efficiency and have more natural immunity to radiation, due to them being wide-bandgap semiconductors. Equally important is the use of the correct driver that will allow reliable operation and maximize the benefits of the GaN FETs. Some of the key driver requirements are: a well-regulated gate drive voltage; high source/sink current capability and a split driver output stage.
-
product
Fault Simulation
Concurrent Fault Simulator
TurboFault combines high performance, versatility and accuracy. It is highly competitive with hardware accelerators for classical test fault grading. It supports synchronous and asynchronous designs at the gate level, including tri-state gates, latches, flip-flops, single and multi-port RAMs, complex bus resolution functions, and User Defined Primitives (UDPs).
-
product
Gated IF RCS Systems
Innovative Technical Systems has designed many instrumentation systems for radar cross section (RCS) measurements. Some of the designs are based around standard network analyzers for signal processing, while utilizing high PRF short-pulse RF transceivers with gated IF architecture. The modular design approach uses separate transmitter and receiver modules for monostatic or bistatic measurements. Compact module design provides flexibility to mount the transmitters and receivers close to the antennas. Dual-channel designs permit full polarization matrix measurements with either electromechanical or solid-state switches. Modules are available in various bandwidths that extend from 100 MHz to over 100 GHz.
-
product
Multifunction Module for 34970A/34972A
34907A
The Keysight 34907A module for the 34970A/34972A Data Acquisition/Switch Unit allows great flexibility for a variety of sense and control applications. It combines two 8-bit ports of digital input and output, a 100 kHz gated totalizer, and two 12V analog outputs - all on a single earth-referenced module. The digital inputs and totalizer input may be included in a scan. Alarm limits for the digital and event counter inputs are evaluated continuously, capturing and logging alarm conditions even between scans.
-
product
Time Domain/Fault Location Analysis For E5061B
E5006A
The E5006A Time Domain/ Fault Location Analysis option allows you to locate the discontinuities and mismatches of devices such as cables. By employing the gating function in the time domain and transforming the data back to the frequency domain, you can remove unwanted responses of connector mismatch in your fixture. In addition, the cable SRL (Structural Return Loss) analysis capability is provided with the E5006A.
-
product
Mini Receiver
FB7-NX
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
product
Photometer II
Spectra Film Gate
The Spectra Film Gate Photometer II offered by Spectra Cine is a significant advance in the field of photometry. It is extremely sensitive and solid state throughout. Reads directly in printer steps of 0.025 log exposure units. The large, uncrowded scale has an 80 printer point range and affords ease and accuracy in reading. A variety of probes are available for use in Acme optical printers, Bell & Howell Model "C", "J", and "A" contact printers, ARRI printers and Oxberry printers.
-
product
Intensified Cameras - Ultra-Sensitive CMOS Cameras from Deep UV to NIR Spectrum
iCameras
The cameras are equipped with a high-resolution sensor with high frame rate for excellent quality of image production, which is well‐suited to detect high speed moving objects or ultra-fast phenomenon.The mechanical architecture of the iCamera is small, compact and light-weight, especially designed for easy integration into any system.The iCamera features an exceptional sensitivity based on high QE image intensifier - ultra-fast gating technology down to a few nanoseconds, which allows it to be coupled with a laser source to perform high fidelity active imaging.
-
product
Single Photon Detector System For Near-Infrared (1.3 - 1.6 Um Wavelength) Waves With Liquid Helium (LHe) Cryostat
Insight Product Company is proud to offer Single Photon Detector System for Near-Infrared (1.3-1.6 um wavelength) with Liquid Helium (LHe) Cryostat. Insight Product Co. offers superconducting single photon detectors and ultra-low noise registration systems for the near infrared range. All systems operate in continuous mode, no gating required.
-
product
Multi Functional VME Logic Module
MDGG-16
The MDGG-16 is a single wide 6U VME multi functional FPGA based delay logic and timing module which provides often needed functions as gate generator & pulse generator, logic fan in - fan out, coincidence register and scaler / pre-scaler. The module has 16 LVDS/ECL inputs and 16 ECL outputs on pin headers and 2 NIM inputs as well as 4 NIM outputs (Lemo), which are free configurable in regards to their functionality.
-
product
High Current / High Voltage Pulsers
DEI Division
Berkeley Nucleonics Corporation
is optimized for high impedance capacitive loads, driving extraction grids and deflection plates, and pulsing or gating power tube grids. It generates an output voltage of 6,000 volts with rise and fall times less than 60ns, with very flat voltage pulses from 160 nanoseconds to DC into a capacitive load.
-
product
Interface and Isolation
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
product
Microprocessor Supervisors
ST’s microprocessor supervisors are more sophisticated devices that can include watchdog and early power-fail warnings (power-fail in/power-fail out (PFI/PFO)), push-button reset functions and battery monitoring. Microprocessor supervisors with a switchover function preserve SRAM data in the absence of system power by automatically switching to batter backup when power fails. A chip-enable gate automatically write-protects the SRAM when the Vcc begins to fall.
-
product
Analog Oscilloscope
CS-406
*OSCILLOSCOPE: 40 MHz Dual Trace,Dual Trigger. 1mV Sensitivity. 10ns Resolution. *COUNTER: 5 Digits 0.36" Red LED Display. 0.1Hz~50MHz Auto Range. 0.001Hz Resolution. Auto Gate Time. Auto Detect,Auto Reset. 1mV Sensitivity.
-
product
test measurement unit
ITC59100 Rg/Qg
The ITC59100 Test Measurement Unit (TMU), which plugs into the ITC59000 Test Platform, performs gate charge (Qg) measurements that conform to MIL-STD-750C, Notice 2, Method 3471 and JEDEC Standard JESD24-2. In addition the ITC59100 TMU performs an internal gate resistance (Rg) test method that conforms to JEDEC Standard JESD24-11.
-
product
MOSFET Drivers
Renesas' product portfolio includes MOSFET gate drivers for 3-phase motor applications. The drivers have built-in detection/protection functions and are suitable for inverter driver applications such as EGR, HVAC and EPS. Line up the products with LDOs for MCU, 24V battery system capability, built-in current sense amplifiers, and motor angle detection function. The products support unit downsizing and high performance.
-
product
Retractable Sources
Veeco’s retractable sources address fundamental limitations of MBE, including source capacity, source removal for maintenance and system uptime. The retractable source allows an individual source to be withdrawn and isolated from the growth environment with the source gate valve and then removed without venting the entire chamber. The source can then be easily refilled with the same material or a new material before being remounted at standard positions to the growth module, allowing growths to continue with minimal interruption. This saves the user from re-qualifying new source to substrate distances and multiple weeks of downtime by avoiding the process of an entire system vent and bake. In addition, the differential pumping option provides a marked improvement in base pressure around the source to reduce contamination of the source material and provide longer lifetimes for sources in corrosive and oxidizing environments. Veeco’s retractable source is the leading solution for material flexibility, system productivity and enhances our leadership with the patented SUMO source technology.
-
product
Frequency Counter Products
53200 Series
The Keysight 53200 Series of 350 MHz universal and RF frequency counter/timers serve all of your frequency and time interval measurement needs. 3 available models offer resolution capabilities up to 12 digits/sec single-shot frequency resolution on a one second gate. Single-shot time interval measurements can be resolved down to 20 psec. All models in 53200 series offer new built-in analysis and graphing capabilities to maximize the insight and information you receive. Use the connectivity of your choice: LXI-C/Ethernet, USB, GPIB. Additionally, an optional battery is available to increase portability and maintain time base accuracy.
-
product
C Series Serial Interface Module
The C Series Serial Interface Module adds RS232 or RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the field-programmable gate array (FPGA) to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The C Series Serial Interface Module supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. You can choose from both enclosed and non-enclosed modules.
-
product
DDS Function Generator, Digital Control 10MHz Or 20MHz, With/without USB/RS232 Interfaces
TG2000 Series
0.001Hz to 10MHz/20MHz frequency range6 digits or 1mHz resolution1ppm stability and 10ppm one year accuracyLow distortion, high spectral purity sine wavesInternal phase continuous sweep, lin or logAM, FSK, gated and tone switching modes5mV to 20V pk-pk from 50 or 600 OhmsStorage for multiple instrument set-upsUSB and RS232 Interfaces (TG2000 only)
-
product
CAMGATE Test Kits
Series 457
The VP Series 457 CAMGATE mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 457 provides interface compatibility using the Virginia Panel ITA G12 interface. The ITA frame is offered as an option for those preferring to provide their own ITA Interface. The CAM/GATE utilizes a cam roller system for precision guiding and smooth operation and 1.00” push plate movement. The gate assembly is movable to three different positions which allows for the versatility of top side probing, or relocating the frame assembly for PCA’s the have tall components.
-
product
6U VPX FPGA Cards
Curtiss-Wright Defense Solutions
FPGAs have revolutionized the way digital signal processing (DSP) subsystems are configured. With a large number of gates, hardware multipliers, and high-speed serial interfaces, FPGAs enable sophisticated applications, including radar, signal intelligence, and image processing, which rely on repetitive processing that can be expressed in highly parallel form. FPGAs perform exceptionally well in FFTs, pulse compression, filters, and digital up/down converters.
-
product
CoreCommander
While many ICs are equipped with a JTAG (IEEE Std. 1149.1) boundary-scan register (BSR), a significant number of microprocessors and DSPs can be found with deficient or even non-existent BSRs. CoreCommander Micro uses the on-chip debug mode of processors to access ports and embedded peripheral controllers to promote ''kernel-centric'' testing. Similarly, in the case of today's Field Programmable Gate Arrays (FPGAs) test engineers can ''bridge'' from the JTAG interface to the resources of the gate array itself. Our CoreCommander FPGA product implements a translatorinterface that allows our JTAG hardware to control embedded IP cores via a variety of bus interfaces (e.g. Wishbone Avalon etc.).
