Safety
-
Product
37-Pin D-Type Male Solder Pin HV
92-960-037-MHV
D-Sub Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
Traction Test Rectifiers
-
A traction test system is defined as a rectifier with a DC output voltage above 400 VDC to a maximum of 4,500 VDC. (Kinetics manufactures only air-cooled systems) A Kinetics test system includes the required OSHA designated safety features for testing power supplies as a minimum for operator interface.
-
Product
NI-9210, 4-Channel, 14 S/s Aggregate, ±80 mV C Series Temperature Input Module
784788-01
Temperature Input Module
4-Channel, 14 S/s Aggregate, ±80 mV C Series Temperature Input Module - The NI‑9210 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The NI‑9210 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range.
-
Product
sbRIO-9236, Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
781580-01
Strain/Bridge Input Module
Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The sbRIO‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The sbRIO‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. Non-enclosed modules are designed for OEM applications.
-
Product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
-
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Phase Sequence Indicator
PHS 863
-
Two Functions in one unit including open phase and phase sequence. Large Size alligator clips can easily clip on switch-board terminal. Highly Reliable : Identifies 3 phase sequence and open phase check. Functional design : This model is ideal for installing conveyor lines, pump systems and interconnected drivers. Safety approval : CE marks EN 6101-1 CAT. III. EN 61010-2-031
-
Product
Sound Level Meters
-
A sound level meter is a measuring instrument used to assess noise or sound levels by measuring sound pressure. Often referred to as a sound pressure level (SPL) meter, decibel (dB) meter, noise meter or noise dosimeter, a sound level meter uses a microphone to capture sound. The sound is then evaluated within the sound level meter and acoustic measurement values are shown on the display of the sound level meter. The most common unit of acoustic measurement for sound is the decibel (dB); however, some sound level meter devices also determine the equivalent continuous sound level (Leq) and other acoustic parameters. With a portable sound level meter, industrial hygiene and workplace safety professionals can measure sound levels in multiple locations to ensure environmental conditions fall within recommended exposure limits (RELs). Some sound level meter devices can be permanently installed for continuous monitoring of sound levels at a work or job site.
-
Product
Vibration Monitoring
-
Vibration tests must be safe and reliable and this is especially true for high value specimens in critical aerospace testing applications. Here, m+p Coda offers maximum safety: The monitoring system captures and records data such as acceleration, temperature and strain continuously during vibration tests - irrespective of the vibration control system in use. Each channel can be configured separately for total flexibility.
-
Product
Personal radioactivity detector
EcotestVIP
-
EcotestVIP is the one and only premium class dosimeter in the world. Created by the leading specialists for successful people who put high value on their own safety. The monitoring device is a combination of the best technical specifications and elegant design.
-
Product
Certified RTOS
LynxOS-178
-
The software industry is concerned with safety and is facing big challenges to make the process of certification (to any standard) more repeatable, more efficient, and more cost effective. The general software industry has been working on software re-use and modularity for many years but these concepts only touched the surface of the DO-178B industry.The LynxOS®-178 RTOS is the first and only hard real-time DO-178B level A operating system to offer the interoperability benefits of POSIX® with support for the ARINC 653 APplication EXecutive (APEX).
-
Product
Personal Voltage Detectors
-
*Provides another level of safety for line crews, storm restoration workers and first responders*Alerts user to the proximity of electric fields or energized electrical equipment with a loud alarm and bright lights*Frequency of alarm increases as the user gets closer to the electrical hazard*Detects voltage above line-to-line*Typical initial warning distance is about 7 ft from a conductor*Warning distance increases with higher voltages*Field replaceable 9V battery with low battery indicator
-
Product
Pressure Calibrators
-
Nagman Instruments & Electronics Pvt. Ltd
In any industry, a lot is usually riding on strict pressure settings like the operations, safety systems, etc. Pressure calibrators help in ensuring that the pressure devices are measuring and displaying accurate values. Nagman offers a range of well built, rugged, reliable, easy to use, budget friendly options of pressure calibrators that you can choose from based on your needs.
-
Product
NI-9263, 100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module
783740-01
Voltage Output Module
100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module - The NI‑9263 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST‑traceable calibration. The NI‑9263 module includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
0.25° Accuracy Full Attitude Surface Dynamic Motion Sensor
DMS-525
-
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.
-
Product
CT/PT Bus-Bar Safety Protector
6450
-
The TESCO CT/PT Bus-Bar Safety Protector (Catalog No. 6450) has been developed to assist in the safe disconnect of a hot sequenced current transformer. After service is disconnected, the TESCO CT/PT Bus-Bar Safety Protector is slid over the bus-bar of the load side of the transformer and prevents accidental connection and/or arcing.
-
Product
External Fire Exposure Test Machine, Battery Safety Testing
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL external fire exposure test machine is applicable to the standard UL 2580.
-
Product
Gas Chromatography
-
Gas chromatography (GC) helps scientists ensure the safety, quality, and purity of our food, air, water, and pharmaceuticals; determine the composition and consistency of fuels and chemicals; and test for controlled substances in criminal investigations and sporting competitions.Agilent gas chromatography systems combine innovative technology, Instrument Intelligence, and legendary reliability to meet the needs of analytical testing and research laboratories across a broad range of applications, such as environmental, food safety, forensics, energy & chemicals, and more. Integrated Instrument Intelligence helps avoid GC problems before they affect chromatographic performance to optimize uptime, cost of ownership, and confidence in results.
-
Product
High-Voltage & Control Measurement
-
PMK Mess- und Kommunikationstechnik GmbH
As a developer and manufacturer of high-voltage and control measurement technologyand high-voltage safety accessories, ROSS Engineering Corp is a long-standing partner of PMK.We are pleased to make this coveted technology accessible to you through our international sales network.
-
Product
DBAir Safety & Environment Sound Level Meter
01GA141SE
-
For professionals looking for sound measurement technology capable of a wide variety of applications, look no further than the dBAir Safety & Environment model.
-
Product
High Voltage Switching Systems
HXV Series
-
HXV products are high voltage systems intened for Hi-pot / IR or High voltage switching. They can be configured to drive from 32 to 128 switch points per chassis and can be configured as multiplexer (1xN) or Matrix (NxM) configurations. Stand HXV chassis are used for signals up to 5000 VAC rms ( 7400 V peak ) and can carry up to 5 amps of current. Custom systems can be built up to 25KV. Most of the modules used in these systems are 1xN multiplexers or 2x4 matrix modules that can be combined to form larger multiplexers or matrices. Connector options for standard HXV include 5 way banaba jacks / binding posts, Shrouded Banana Jacks or SHV ( High voltage BNC) if you need to use a high voltage cable with a grounded shield for safety applications. Control options include 10/100BaseT Ethernet LAN, RS232, GPIB or optional manual control. Standard HXV systems use high voltage reed relays. Custom HXV systems up to 25KV use application specific relays and connectors from a variety of vendors based on required specifications.
-
Product
Yellow Industrial VOM
260-8XPi
-
The 260-8Xi offers all of the advantages of the Simpson 260-8, plus several new safety features. The bright yellow ABS housing is easy to see and also provides increased drop protection. The 260-8XPi includes a resettable overload protection circuit and audible continuity check. Both versions come with batteries, manual and test leads with alligator clips.
-
Product
Applications
-
Whenever safety and cost efficiency are at stake, SuessCo sensors and monitoring systems are the first choice. Individual solutions can be developed for a large number of application areas.
-
Product
Shoe Dielectric Resistance Tester
UI-FT07
-
Shoe Dielectric Resistance Tester, also named as shoe high voltage withstand tester, is used to test shoe sole and heel electrical insulation, to check shoe performance of voltage withstand and current leakage. It is to test safety shoe dielectric resistance ability (Electrical Hazard Testing) as mentioned in ASTM F2412.
-
Product
Seals
-
Flowserve mechanical seals and systems represent a collection of trusted products supported by strong aftermarket services, providing users with both safety and environmental benefits.
-
Product
Electrical Safety Tester
-
PSE AG has developed an electrical safety test that combines different tests for the testing of PV modules. With our four-in-one tester it is possible to test the following according to IEC 61215-2 and IEC 61730:
-
Product
Safety Footwear Impact Tester
SG-P11A
-
This machine, incorporating a steel striker adaptered to fall freely on vertical guides from a predetermined height to give the required impact energy to the toe of safety footwear for measuring the degree of the dent. In addition, the toecap should not develop any cracks on the test axis with go through the material.
-
Product
AC Voltage Detector
VT-2
-
The Non-contact AC Voltage Testers are easy to use — just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there’s voltage present. Electricians, maintenance, service, safety, personnel, and homeowners can quickly test for energized circuits in the workplace or at home.
-
Product
ALD Applications
-
Atomic Layer Deposition (ALD) has the potential to optimize product design across a wide array of applications from making silicon chips run faster, to increasing the efficiency of solar panels, to improving the safety of medical implants.
-
Product
Multi-Sensor Thermal Imaging Camera for Condition Monitoring
A310 PT
-
FLIR A310 pt thermal cameras can be installed almost anywhere to monitor the condition of your critical equipment and other valuable assets. Designed to help safeguard your plant and measure temperature differences, they allow you to see problems before they become costly failures -- preventing downtime and enhancing worker safety. FLIR A310 pt is ideal for various applications that require temperature measurement capabilities including: substation, transformer, waste bunker, and coal pile monitoring.
-
Product
Electric Safety Tester
PV-215
-
The multifunction device PV-215 allows quickly and safely carrying out the electric safety tests provided for a PV system (section in DC) and the functional test of modules/strings the system consists of according to the requirements of Standard IEC/EN62446.
