Solenoid Testers
-
Product
High Voltage Surge Testers
10000HVST
-
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
Product
Loop / PFC Testers
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2715 is a loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
Product
Avionics Data Bus Tester
Distributed CORVUS
-
Distributed CORVUS works in conjunction with CORVUS-300 to isolate bus anomalies and fault resolution. The Transmit unit, C-9235-TX, sends 1553 like data pattern through a bus stub and coupler to the Receive unit, C-9235-RX, on another stub. This will measure insertion loss, possible bit errors and correct polarity. The Receive unit can also be used to give a digital scope representation of the active data bus showing signal quality and peak to peak amplitude.
-
Product
Glow Wire Tester
TF346
-
TESTEX Testing Equipment Systems Ltd.
Glow Wire Tester, to determine the resistance to fire insulating parts. The testing of electro-technical products for fire hazard is conducted by simulating as closely as possible actual effects occurring in practice. Parts of electro-technical equipment which may be exposed to thermal stress due to electric effects & deterioration of which may impair safety of equipment shall not be unduly affected by heat & fire generated within the equipment.
-
Product
Network Cable Tester
PA-40
-
The PA-40 is designed to check both shielded and unshielded twisted pair (STP/UTP) and coaxial BNC-type network cables. With the push of a button, it tests all wires for continuity, miswiring, and polarization. Dual-colored LEDs let you identify correct and reversed pairs; using the included remote unit, cables may be tested before installation or after installation. Features tip/ring polarity test. Uses 1 9V battery.
-
Product
Automatic Battery Testers
-
T100BT is an innovative, modular battery testing equipment able to combine, on a single test platform, all the tests required to detect any possible defect on battery cells and modules: from defective cell wiring, to geometrical or surface irregularities, to out-of-specs performances.The battery tester is designed for the high-volume production test of battery modules composed by prismatic, cylindrical, or pouch cells, as well in a Lab/NPI version for engineering, prototypes and low-volume battery testing. The complete configurability allows you to equip the tester with the modules and tools you need to test your products, reaching the desired throughput.
-
Product
Sulphur Content Testers
-
X-ray fluorescence sulfur in oil analyzer, dark petroleum products sulphur content tester (tubular oven method)
-
Product
Battery Safety Testers
-
Chroma Systems Solutions, Inc.
The flexibility of our battery test equipment provides customers a test environment specifically for their application requirements.
-
Product
Current Transformer Tester
CTT
-
The CTT is designed to test the current transformer ratio, Phase shift, Polarity, Excitation, Saturation, Winding resistance and Insulation resistance using the voltage method in compliance with ANSI/IEEE C57.13.1 and IEC 60044-1 standards, where voltage is applied to the secondary X terminals of the current transformer.
-
Product
Aerial Lift Testers
ALT Series
-
HVI produces AC voltage testers that perform boom and liner testing, with models available up to 300 kV AC for boom testing and 10 kVA for liner testing. The ALT Series is designed for AC voltage testing aerial lift devices. The standard models available are rated 120/60 kV AC, 200 kV AC, and 300 kV AC, rated up to 7 kVA.
-
Product
Earth Ground Testers
-
Plant maintenance is a must! Confirming your ground resistance is crucial for instruments and machinery. Our Earth Ground Testers provide simple accurate measurement of earth resistance.
-
Product
Medical Withstand Voltage Tester
2670YM
-
Shenzhen Chuangxin Instruments Co., Ltd.
Medical Withstand Voltage Tester，2670Y Medical Withstand Voltage Tester Has All The Function Of The Conventional Withstand Pressure Tester,And Increasing The Arc(Flashover)Detection Function,It Can Test The "Flashover" Phenomenon Of Electrical Equipment Intuitively,Accurately,Rapidly And Reliably Through The External Oscilloscope,The Measured Electrical Equipment Without "Flashover" Phenomenon,
-
Product
Brushless Motor Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing general properties of DC brushless motors.
-
Product
Mud Cake Friction Coefficient Tester
NZ-3A
-
Zhengzhou Nanbei Instrument Equipment Co. Ltd
With the development of drilling technology, special technology wells, directional wells, cluster wells do more and more. Lubricating performance requirements of the drilling fluid is also increasing, the processing agent for drilling fluid lubricant is also increasing year by year. Differences in the quality of the lubricant, together with a reasonable need for compatibility, we need an instrument to evaluate.
-
Product
Transformer Winding Resistance Tester
KRI 9310
-
KRI 9310 adopt Kelvin four-wire testing method, which effectively eliminates the influence of the resistance of the test line on the test results. It can be able to increases the current to 10A by which can test extremely low resistance to 0.01 Ω(such as amorphous alloy, Copper-nickel, nickel-chromium-iron, iron-chromium-aluminum etc). For the tested objects with high resistance value (CT/PT), the instrument can extend the range to 20 kΩ，so the wide resistance test range enables KRI9310 can cover 80% of the power transformer products on the market and switchgear bus-bar cable etc. The power of the tester use the built-in rechargeable lithium battery that can test hundreds of transformers by one time charging.
-
Product
Digital Iron Tester
MW14
-
The Milwaukee MW14 High Range Iron Photometer lets you go digital with your testing. No more hit and miss testing with strips. Great for aquariums, Aquaculture & Coral, labs, water conditioning, classroom and more. This meter is also ideal for educators that want their students to learn the basics of water quality analysis to apply in the real world.
-
Product
Ground Resistance Tester
-
Weshine Electric Manufacturing Co., Ltd
1.Soil resistivity tester supports 2, 3 and 4wire grounding resistance measurement. 2. 4digit large LCD display with white screen backlight, suitable for use in dimly lit places. 3. IP65 protection grade, good waterproof, compact and portable, supports multiple functional tests.
-
Product
Winding Resistance Tester with Demagnetisation Circuit
WRT-10D
-
The WRT-10D is a high performance winding resistance tester designed for power transformer and large motor applications. It is equipped with a bright LCD display, a rugged high quality cable set, a built-in printer, a full QWERTY keypad and a demagnetisation circuit.
-
Product
Installation Safety Testers
VDE 0100
-
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
Product
Linear Motor Tester Lite
BK2019B
-
With the BK2019B, you can test for open/short circuits, operating current and even vibration level. Because it has only one purpose, it is very easy to set up and use and it's so small it can fit into the average briefcase.
-
Product
Surge Tester (Impulse Winding Tester)
SS6815 / SS6815F
-
Surge testers (impulse winding tester) is used for testing and check the insulation grade of turns between turns, insulation grade of layers between layers, insulation grade of windings between turns. It is used widely for transformer, current sensor, voltage sensor, relay, contactor, inductor, motor, generator, valve coil, voice coil, etc.
-
Product
Earth Resistance Tester
M71
-
M71 has been developed to measure earth resistance with 2 wires and 3 wires by voltammetric method in compliance with standard IEC/EN61557-1.
-
Product
UMTS / GSM Tester
-
manufacture a range of items that can be used in UMTS and or GSM propagation testing. These products have been designed against customers requirements.
-
Product
Shoe Flexing Tester
UI-FT29
-
Shoe Flexing Tester is suitable to test complete shoe flexing resistance ability as per SATRA TM92. It is suitable to test all kinds of shoes and can be used to for SATRA TM77. This machine can be made to test in low temperature. Besides, Shoe flexing & water penetration tester is available.
-
Product
Horizontal Tensile Tester
BLD-200H
-
BLD-200H Horizontal Tensile Tester can be used for peeling, stripping and other performance tests of adhesives, adhesive tapes, pressure-sensitive tapes, medical adhesive bandages, protection films, release paper, laminated films, leather, woven bags and paper.
-
Product
Battery Internal Short Circuit Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Internal Short Circuit Tester
-
Product
DataComm & LAN Testers
-
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
Product
Rockwell Hardness Tester
Versitron® Series
-
Newage Testing Instruments, Inc.
The Versitron Rockwell hardness testing system is the industry workhorse of hardness testing - designed to meet the toughest challenges: clamp large parts, operate in poor environments, and test high volumes - all with less service problems and less operator skill requirements. Available with 2 different test stands types (in a range of sizes) and 2 test heads and also a wide range of other options.
-
Product
Digital Earth Resistance Tester
8020 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage. ● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Frequency : 820Hz.● 0Ω adjustment.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.● Simplified measurement probe is also provided for two-wire measuring method.
-
Product
DC Hipot Testers
DPW Series
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
These portable testers have been designed to be used in testing high voltage equipment in power engineering. Routine testing of the insulation and leakage is a necessary requirement for surge arresters, cable breakdown testing, capacitor charging and other laboratory use.
