CATV Test
-
Product
47~862MHz Four outputs FTTP CATV optical receiver
P9428
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai P9428, the operating bandwidth of 47 ~ 862MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver. Products with high sensitivity optical receiver tube and Huatai special low noise matching circuit..
-
Product
Dust Test Chamber
-
Xi'an LIB Environmental Simulation Industry
Used to test the durability and sealing integrity of products (electronics, automotive parts, materials) against harsh, dusty conditions.
-
Product
PC Based Test Setup for Electric Iron Testing
-
SCR ELEKTRONIKS make PC Based Test Setup for Electric Iron Testing is useful to carry out various tests mentioned in IS 366:1991 clauses 10,11,12,13 & 14 on the Iron under test.
-
Product
Lithium Battery Testing Equipment
-
Fuzhou Fuguang Electronics Co., Ltd.
Lithium Battery Testing Equipment
-
Product
Test Tables / System Solutions
-
WEETECH, as a manufacturer of test equipment, offers its customers also a "Ready To Use" test system solution. It consists of the test table, the customer-specific adaptation as well as the test device, and is very quickly ready for use at the customer's site. According to the customer's requirements, the set-up is designed as a system with permanently installed adaptations for the production of constant cable harnesses in large quantities or with interchangeable adapters for the flexible production of different cable harnesses. Depending on the application, a larger table version or a smaller desk version is available. Various interfaces are available for integrating these solutions into a complete production automation system.
-
Product
Ionic Contamination Test Systems
CM+ Series
-
The Contaminometer (CM+ Series) system was originally developed by Protonique, the business of industry guru Brian Ellis. They also featured in the early development programmes of "cleanliness measurement" carried out by the US Department of Defense at China Lake in the 1970s. Historically, International Standard IPC-J-STD001 stated that assemblies be cleaned to a value of <1.5µg/cm2 of NaCl equivalence. However, the new design is linked to the introduction of the new process control metric introduced by Gen3 Systems: Process Ionic Contamination Testing. The CM+ Series measure the amount of ionic contamination in accordance with all existing test methods, often referred to as ROSE testing, as well as the new PICT test.
-
Product
Reliability Testing
-
ELES Semiconductor Equipment SpA
ELES designs and manufacturers reliability test solutions to verify the performance of integrated circuits from concept validation to high volume production during all the test phases. No other company can provide universal equipment for all the reliability tests, or can guarantee a seamless data flow between phases or can apply on chip embedded reliability engineering for data tracking and failure investigation. Clients use our functional test data to proactively analyse variations between lots, between temperature extremes and during lifetime (often these defects escape ATE). The improvements to products and processes needed to arrive at zero defects cannot be driven by the quantity of Big Data alone, the quality of reliability data is a strategic advantage that only ELES can provide.
-
Product
Single Site Test Handler
3210
-
Chroma Single Site Test Handler 3210 supports various package types such as BGA series, QFP series, QFN, TSOP, and more. The handler is primarily designed for early device design and engineering validation.
-
Product
Fuel Cell Test Accessories
-
Scribner extends its groundbreaking line of tabletop fuel cell testing equipment with the 885 Fuel Cell Potentiostat.
-
Product
Test Automation Platform (TAP)
-
The Keysight Test Automation Platform (TAP) provides powerful, flexible and extensible test sequence and test plan creation with additional capabilities that optimize your test software development and overall performance. TAP is a modern Microsoft .NET-based application that can be used stand-alone or in combination with higher level test executive software environments.
-
Product
Pressure Test & Calibration Pumps
-
Pressure Test Pump is a hand operated pressure pump designed to generate pressure from 95% vacuum to 1,500psi (100bar). A high-quality screw press is designed for fine pressure adjustment, with an adjustment resolution up to 10 Pa (0.1 mbar). A specially designed shut-off valve makes the pressure as stable as possible during calibration. A built-in gas-liquid isolator protects the pump from moisture and dirt to reduce the need for maintenance. Two hand-tight quick connectors installed on the pump allow easy connecting and disconnecting to the test pump without the need for PTFE tape or wrenches. The 918 is an ideal comparison test pump for pressure instruments calibration.
-
Product
Water Meter Test Bench
LS-4B
-
Hong Kong Songyang Industrial Ltd.
The water meter test bench is made up the platform, clamps, back and front pipe, flow counter group, standard measuring instrument and the outlet valve.When the inlet is connected with the stable water source, the water will get to the standard measuring instrument through the straight pipe. Compare the value of the checked water meter with that of the standard measuring instrument, the valve error that the water meter reads will be acquired.
-
Product
Pressure Comparison Test Pump
PCP Series
-
Nagman Instruments & Electronics Pvt. Ltd
Budget Solutions. Very Low Maintenance Cost. Compact & Easy to carry for Lab & Field use. Screw RAM Pump. Adjustable Foot.
-
Product
Meter Test Board
WECO 2150
-
Model 2150 automated test system is a fully ANSI compliant testboard that uses a single voltage and three independently controlled isolated current sources to test all electromechanical and solid state meters up to 50 Amps. Utilizing a precision laser optics system, the Model 2150 can test meters through the most grime-coated covers with unfailing accuracy. This same laser technology makes it possible to test using the disk’s edge without wasting time with the tricky optics adjustments found with other test systems.
-
Product
(1000kN) Fatigue Testing Systems
8805
-
The 8805 is a 4-column, 1000 kN servohydraulic fatigue testing machine. It features a high-stiffness and precision-aligned load frame, with hydraulic lifts and locks, and an actuator in the upper crosshead.
-
Product
Audio Panel/Amplifier Test Fixture
TA-200
-
The Model TA-200 test panel was designed to allow Avionics shops the capability to test and troubleshoot both today's new generation audio panels as well as the standard audio panels of the past. The testing of these panels over the years has always proven to be a very time consuming job for most shops because of the limited capabilities of any past test panels.
-
Product
Battery Testing System
C8000
-
The Cadex C8000 stands in a class by itself in flexibility and affordable price. Test SMBus batteries, monitor cell balance and capture load signatures to observe batteries with a unique load protocol. Add a thermal chamber, an external load bank, a safety circuit and alarm to form a command center and you begin realizing the unique qualities of this fine battery testing system.
-
Product
Photonic Test & Measurement
-
Keysight offers a wide-range of innovative test and measurement solutions to accelerate the progress of next-generation intelligent optical networks. Keysight's mission in the optical market is to shorten time-to-market and reduce cost-of-test for customers in R&D and manufacturing, as well as enable new technologies which include innovative optical components, network elements & systems, and all-optical fiber networks.
-
Product
Design & Test Software
-
Industry-Leading Design, Emulation, and Test Software.Harness the power of digital twins, artificial intelligence, and automation to streamline workflows, break down silos, and accelerate test cycles.Find out why so many innovators trust Keysight to build their next breakthrough. With software spanning electronic design automation (EDA), instrument control, emulators, IT operations, and application delivery, your next project's only limitation is what you dare to dream.
-
Product
Automated Regression Testing For BACnet
BOTS
-
BOTS is an easy-to-use BACnet regression testing tool for Windows. BOTS runs under Windows 7/8/10, and Server 2012. It provides a robust set of regression tests based on the 135.1 standard, including BTL additional tests and PolarSoft's own developer-oriented tests. BOTS includes many features tailored to the needs of QA Testers and product developers, at a price that's lower than competing systems that cost more than ten times as much.
-
Product
Unit Testing
-
Hitex offers a unit testing service for C/C++ application source code using the well-known test tool TESSY. For this service, the customer provides their source code of the C/C++ functions to be tested, ideally along with the specifications of the functionality and comprehensive comments in the source code.
-
Product
APU Test Cells
-
Atec is a leader in test cell design and construction for aircraft auxiliary power units (APUs). We are licensed and experienced for work with all major OEMs, DoD, and US Allies. Our Phoenix™ APU Cells feature common configuration, modular utilities, and fast installation and startup.
-
Product
Motor Test Port
MTAP2
-
We know safety is number one priority in any motor reliability program that is why PdMA developed the MTAP2, our answer to safe electric motor testing. With the combination of MCEMAX® or EMAX, the MTAP2 makes testing easier, faster and above all safe!
-
Product
Testing Multi-Radio Mobile Devices
IQxstream
-
With LitePoint's IQxstreamTM mobile test system you will have all the capability you need to fully test many 3G and even 4G cellular radios and standards. Moreover, the system is designed to reduce per-device test time and cost because of its unique parallelism architecture. A 100 MHz capture capability means that it can test adjacent channel leakage ratios (ACLR) in one, five-channel capture.
-
Product
Environmental Test Chamber
-
Labtone Test Equipment Co., LTD
Environmental test system, Electro-dynamic Shaker, Shock Test Systems, Drop Tester, Bump Test Systems, Combined Environmental Test Systems
-
Product
Test & Support Gear
-
Atec has experience with rugged and reliable equipment required for oil-field applications and the reputation for customer responsiveness and quick deliveries. Our energy history includes several years of re-engineering and manufacturing several test and support energy products. We have the ability to design, re-engineer and assemble items such as: junction boxes, cables, harnesses, printed circuit boards, computer systems, data acquisition software, valves, solenoids, & gear boxes.
-
Product
Pre-Selectors for EMC test
Emissions
-
These Pre-Selectors are high specification, switched band filters which track the scanning of the EMC Analyser. Control is via USB link from the Laplace EMCEngineer software supplied with SA1002 and SA3000 analysers. Installation and operation is completely automatic, and the filters will synchronise with the analyser scan without any operator intervention. A front panel switch allows manual operation if required.
-
Product
Electrical Safety Test Scanner
19200
-
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
Product
Functional Test
-
Products and systems used to monitor and record data that characterizes the physical integrity and performance of aircraft, engines, and other large structures, as well as automate the functional testing of complex electronic systems.
-
Product
PCB Test Points
-
Test Socket 2mm. Plug 2mm. Measuring Socket 2mm . 2 Pin Test Socket 2mm. Miniature Test Socket 2mm
