Showing results: 1201 - 1215 of 9939 items found.
-
40-182A-011 -
Pickering Interfaces Ltd.
The 40-182A-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
40-183B-011 -
Pickering Interfaces Ltd.
The 40-183B-011 has 6 high current SPST switches in two PXI chassis slots. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 30A of continuous current and switch up to 40V signals. The switch can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.
-
iW-RainboW-G47V® -
iWave Systems Technologies
AMD Xilinx’s KU19P, KU095, KU115 Kintex UltraScale+ FPGADual 64 bit, 4GB FPGA-DDR4 with ECC (Upgradable)31 channels of FPGA GTY transceivers up to 32.75Gbps1Dual ARM Cortex-A7 core processor of 1.2GHz speed32bit 2GB DDR4 for CPU with ECC128MB QSPI Flash & 256MB NOR Flash3U VPX Connector (P0+P1A & P1B+P2A)8 Optical transceivers through MT Ferrule Connector (P2B)
-
NI
PXI MultiComputing Remote Control Modules enable PXI systems to transfer data at multigigabytes per second with only a few microseconds of latency. You can use these models in applications such as real-time tests, hardware-in-the-loop (HIL) tests, and structural tests that need a large number of distributed PXI systems to share data with low latency.
-
LYNXEA_VIS -
AUREA Technology
The LynXea_VIS from AUREA Technology is a stand-alone [400-1060 nm] Time Correlated Single Photon Counting TCSPC module, which fully integrates the Time to Digital Converter and the best single photon avalanche detection (SPAD) counting technologies within the same box. As a matter of fact, TCSPC measurements are now available without assembling multiple boxes!
-
Pickering Interfaces Ltd.
Pickering's PXI programmable load modules offer a solution to applications requiring higher power handling capabilities, up to 15W in a single PXI slot. High Power Potentiometers can easily be formed by using two channels of Programmable Load Resistors in series, using the unconnected terminals as the A and B connections and the link between the two channels as the wiper connection.
-
CPCI-SIP-rp -
ALPHI Technology Corporation
The CPCI-SIP module provides a 3U high performance flexible I/O scheme that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-SIP is the perfect solution.The CPCI-SIP is also available with the Industry Pack lines routed to the CompactPCI P2 connector for application that require rear panel I/O.
-
34980A -
Keysight Technologies
The 34980A General Purpose switches can be used to route signals or to control other devices in an application. These switches are ideal for device actuation, switching loads or power supplies. Both switches offer high power channels up to 150W. The general purpose modules also include a relay switch counter to help predict when relays need to be replaced.
-
M9130 -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai M9130 optical receiving module is designed for ONU optical fiber network unit. This series of product with perfect detect and remote shutting off function adopts high sensitivity receiving tube and Huatai special low noise matching circuit. It is a kind of high index, low power consumption and high cost performance RFTV optical receiving unit.
-
ModTest -
Rotork plc
Modtest 2 software allows the configuration and settings of a Rotork Modbus Module Mk2 inside an individual actuator to be carried out easily and simply over the data bus. In addition, the actuator can also be exercised using this PC based software. The Modtest 2 software is used for diagnostic and maintenance of a Modbus controlled actuator over a serial link from the PC.
-
41-670-101-AABBCC -
Pickering Interfaces Ltd.
The 41/43-670-101 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has four banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
41-670-103-AABBCC -
Pickering Interfaces Ltd.
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 2 channels of 5 or 6-wire or 4 channels of 4-wire.
-
41-752A-001 -
Pickering Interfaces Ltd.
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
41-752A-003 -
Pickering Interfaces Ltd.
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
41-752A-002 -
Pickering Interfaces Ltd.
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.