-
product
PXI 4-Slot BRIC Matrix, 92x8, 1-Pole (2 sub-cards) Dual Bus
40-560B-021-92X8-M
The 40-560B-021-92x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
product
Digital I/O PXI Card
GX5290
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
PXI Flexible Microwave Module, Dual SP6T Terminated 26.5 GHz, Single SPDT 26.5 GHz, 50 Ω, SMA
40-890-004
The 40-890 (PXI) and 42-890 (PXIe) range of PXI microwave modules allows users to specify the mix of relay types, frequencies and quantities based on the application requirements within the capabilities of the module driver card. Choose from the extensive relay selection already available in the Pickering microwave range to create a flexible solution.
-
product
PCI-6519, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Sink Outputs, Bank-Isolated Digital I/O Device
779085-01
The PCI-6519 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6519 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6519 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
product
NI-9206, ±10 V, 250 kS/s, 16-Bit, 32-Channel, 60 VDC Isolation C Series Voltage Input Module
779526-01
±10 V, 250 kS/s, 16-Bit, 32-Channel, 60 VDC Isolation C Series Voltage Input Module - The NI‑9206 performs differential analog input with four programmable input ranges. The module provides up to 600 VDC (400 VDC in Europe) channel‑to‑earth ground isolation, making the module ideal for accurately monitoring large fuel cell and battery stacks. By referencing the module common (COM) to the middle of the NI‑9206 bank, you can measure 16 consecutive cells and remain within 10 V of the module COM.
-
product
ATCA Rear Transition Module
ART104
The ART104 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC104 carrier board. The ART104 is a passive RTM that allows for Management 10/100Mbit Ethernet, Management RS-232 serial interface and PCIe x4 lanes for expansion.
-
product
PXI 2 A Relay Module, 26xDPDT
40-139A-202
The 40-139A-202 (PXI) and 42-139A-202 (PXIe) are 26xDPDT relay modules suitable for high density switching applications with medium power and feature 2 A current capacity with voltage rating to 300 VDC/250 VAC
-
product
Receiver, G3, 500+ Amps, includes Dedicated 500+ Amp Module
310105172
Receiver, G3, 500+ Amps, includes Dedicated 500+ Amp Module.Contacts rated to 1500VDC for low duty test applications.Mating ITA 410105174. (NOT compatible with other VPC Solutions)
-
product
PXI Microwave Transfer Switch, Single, 26.5GHz, 50Ω, SMA
40-782B-531
The 40-782B-531 (PXI) and 42-782B-531 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 26.5GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
Test Finger Apparatus
SCR ELEKTRONIKS focuses on designing a solution around the end use at her customer. Instead of offering a standard instrument for a specific task, we have an approach of customizing the test bench to target the specific goals of the process or test procedure. Our measurement instruments, test modules, electrical power systems & software libraries are developed with this vision, thereby reducing the test system’s time-to-deploy.
-
product
Computer-On-Module
SMARC
SMARC form factor is the only computer-on-module form factor that truly is capable of supporting both ARM and x86 designs. With 314-pins on a high speed MXM3 connector, SMARC can fully cover both typical x86 interfaces as well as typical ARM type low level signals. Using ARM SoCs opens the possibility to leverage the product ecosystem of familiar devices such as tablet computers and smart phones. Alternative low power SoCs and CPUs, such as tablet oriented x86 devices and other RISC CPUs may be used as well.
-
product
PC/104+ Card with 4 IP Slots
PC104p4IP
If you want to use IndustryPack modules with your PC/104+ or PC/104-Plus system, the PC104p4IP is the choice for you. The PC104p4IP combines features you need with simplicity and speed. Up to 4 IP modules can be installed. Standard 16 bit IPs plus 32 bit, and double wide modules fit right in. Each slot has independent operation - control, clocking, IO, power filtering and protection. The PC104p4IP is highly integrated with the PCI and IP interfaces closely coupled within the same FPGA.
-
product
RF Amplifier
SA831
Hangzhou Softel Optic Co., Ltd.
*The microwave low noise amplification circuits are used as forward and backward paths of SA831 products. CATV special RF modules encapsulated by SOT-115 are used as forward paths of SA831 products. The microwave low noise amplification circuits are used as backward paths of SA831 products.*It is more convenient to debug, because of plug-in duplex filters, plug-in fixed (or adjustable) equalizers, plug-in fixed (or adjustable) attenuator plug-in output splitters and scientific and rational on-li...show more -
product
VXT PXI Vector Transceiver, 380 MHz to 6/8/12 GHz
M9415A
The Keysight M9415A VXT PXIe vector transceiver integrates a VSG and a VSA from 380 MHz to 6, 8, or 12 GHz in a 3-slot PXIe module with up to 1.2 GHz bandwidth.
-
product
Rugged, Long Gauge Length Extensometers
Model 3543
Jinan Testing Equipment IE Corporation
With over 15 years of proven reliability in the world’s most demanding testing environments, the Model 3543 extensometer is designed to survive in those applications where standard axial extensometers would not. Designed by Epsilon, the Model 3543 was created to survive specimen failure by separating into two halves, thus preventing permanent damage to the module body. During operation, the upper half of the extensometer pulls out of the main body. Tapered measuring beams activate strain gaged f...show more -
product
16-CH Discrete Input 16-CH Discrete Output Module
HSL-DI16DO16-M-NN
- Input voltage: ±40 V (Max)- Output switching capacity: Single channel 500 mA; all channels 60 mA at 24 VDC- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ±10 mA (Max) , ±12.5 mA (Peak)- 16-CH digital input and 16-CH digital output. "NN" type for NPN sinking type sensor input or dry contact and NPN sinking type output- Slave ID consumption: 1
-
product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781260-01
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WC...show more -
product
PXI 4 Slot BRIC 150x4 2A 1-Pole Matrix
40-568-002
The 40-568 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 200VDC/140VAC. The 40-568 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable, 1.5m
150275-1R5
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable, 1.5m - The SH96F-96M SwitchBlock SCSI Cable provides connectivity for SwitchBlock modules. You can connect these to the TBX-2809 Terminal Block, which exposes each channel of the switch module to screw terminals.
-
product
e Data Acquisition 32 ch. Module
CPCI-AD320-6U
The CPCI-AD320 module provides a 6U high performance data acquisition subsystem. There are 32 thirty-two 100/200 KSPS ADC’s for maximum performance. Or an opt low cost 16 channel version. The Local DSP can be usedto simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.
-
product
PICMG 1.3 Full-size CPU Card With LGA1151 8th Gen Intel® Core™ I7/i5/i3, Xeon® E, Pentium® Or Celeron® Processor, Intel® C246/Q370/H310, SATA 3.0, USB 3.1 Gen1/Gen2, Dual LAN And DVI-I
SHB150
The SHB150 is based on the latest LGA1151 socket 8th generation Intel® Core™ processors (code name: Coffee Lake) and Intel® C246, Q370 or H310 chipset. The SHB150 features multiple I/O options and high-speed transfer interfaces as well as superior graphics capability (Intel® HD Graphics), making it an ideal solution for smart factory automation. The Intel® Core™-based full-size SBC, SHB150, comes with two 288-pin DDR4-2666/2400 Long-DIMM sockets with up to 32GB of system memory. The PI...show more -
product
PXI BRIC4 FIBO Matrix Dual 60x4 3pin brkout
40-592A-003
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
RF/Microwave Assembly Capability
Teledyne Labtech offers a comprehensive build-to-print microwave module and microwave components manufacturing service. This includes MMIC placement, Au wire bonding, SMT assembly and test.
-
product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 50Ω, MCX
42-877A-102
The 40-877A-102 (PXI) and 42-877A-102 (PXIe) are 50Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
PXI Prototyping Module, 1-Slot, 96-Pin Micro-D
40-225A-101
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber
40-850A-514-M50-HI
The 40/42-850A-514-M50-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Computer-On-Module
CM22301
LinkedHope Intelligent Technologies Co.,Ltd.
CM22301 uses Intel® sixth-generation Skylake platform and Core M low-power SoC processors, and integrates the full functions of CPU, GPU and South/North Bridge on a single chip. The processor provides powerful computing and display performance with dual-core and four threads configuration. Its turbo frequency can boost up to 3.1GHz and the display output resolution can be up to 4K. CM22301 has an amazing thermal design power consumption of only 4.5W (TDP) and can be used for a variety of high-pe...show more -
product
PXI 18 Channel Power Mux 1 Pole
40-665-001
Model 40-660 is a 10-Channel Power Multiplexer, suitable for switching inductive/capacitive loads up to 10A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions). Model 40-665 is a higher density 18 Channel Power Multiplexer with the same specification as the 40-660. Power Multiplexer Modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids.
-
product
Micro Power Modules
VPC offers a wide array of modules with a variety of connection options that are configurable for virtually any interconnect requirement.
-
product
Vacuum
VPC's 2-port position Vacuum modules are available with or without a filter. Made of black anodized aluminum, they are rated to withstand temperatures between -65° C and 200 ° C.