-
product
Relay Tester
LET-4000-R
Regulation and Measurement Module performs the regulation of the DC current and is made with a variable auto transformer (Variac) regulating a three phase DC current, with a power of 8KVA and a three phase transformer of 8KVA with 2V nominal power in the secondary windings. A built-in ammeter and a timer give the information of the current injected and the operation time of the relay under test.
-
product
PCI-6110, 4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device Multifunction I/O Device
777475-01
4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6110 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6110 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6110 dimensions require chassis slots that can accommodate full-length PCI modules.
-
product
PXI RTD Simulator Module, 20 Channel, PT1000
40-263-103
The 40-263-103 is a 20-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - PCIe
Model 7053
- Supports Xilinx® Zynq® UltraScale+" RFSoC FPGA- 16 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2, and 3) interface up to x8- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- Optional front panel dual optical MPO interface for gigabit serial communication- Unique QuartzXM eXpress Module enables migration to other form factors- Navigator BSP® for software development- Navigator FDK® for custom IP development- Free lifetime applications support- Pentek's Quartz Fami...show more -
product
PXI Single 64x4 Matrix 2-Pole Switching
40-533A-022
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109 operations to give maximum switching confidence with long life and stable contact resistance.
-
product
IEEE 1394b/AS5643 Mil1394 (FireWire), Triple-Node Multi-Port, Communications
FW3
The FW3 function module provides IEEE 1394b/AS5643 (Mil1394) support on each of its three nodes, which are configured as 2 nodes with 3-ports and 1 node with 2-ports. AS5643 defined flight ready robustness and active transformer isolation to enable longer cable lengths (20 meter) between nodes. Together these standards provide the deterministic and redundant communications protocol required for Vehicle System (Flight Control) Networks. The FW3 multiple ports per node configuration allows the user to create tree, daisy-chain and looped topologies needed to optimize cable length and weight while creating redundancy.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode
40-852A-018
The 40/42-852A-018 is a PXI/PXIe 8-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI RTD Simulator Module, 8 Channel, PT500
40-263-402
The 40-263-402 is an 8-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
AUTOMATED TEST STAND DESIGN
Automated test systems may be as simple as a laptop with a DAQ module or a stand-alone controller, but they typically require a mix of off-the-shelf and custom hardware. All that hardware is integrated and wired into a test stand. Portable or mobile test stands are ideal for in-the-field research and development and servicing of multiple laboratories or manufacturing lines. Test stand access to the front panels of hardware and subcomponents allows manual configuration of non-automated settings. ...show more -
product
Static Maneuver Module
CTB2PH
Lifasa - International Capacitors, SA
The static control units CTB2PH include, in a compact form, all the components necessary for the operation of three-phase capacitors. The CTB2PH modules employ thyristors instead of the classic contactors. The static maneuver is the ideal solution in installations in which the load current presents rapid and very large fluctuations (load changes in intervals ranging from a few tenths of a second to a few seconds).
-
product
PXI Multiplexer, Single 24-Channel, 2-Pole
40-632A-021-24/2
The 40-632A-021-24/2 is a single 24-channel, 2-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
4AO/4DI Modbus RTU Remote I/O
ND-6124
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
product
Solar Panel Chamber
Specifically designed for the solar industry, these climatic chambers feature specifically designed fixtures to properly measure almost any component related to solar panels including the actual panels, grid-tied photovoltaic inverters, or photovoltaic cells and modules.
-
product
3U CompactPCI Enclosure with 6-Slot Backplane and Redundant Power Modules
cPCIS-3048
- 3U CompactPCI backplane with one system slot and five peripheral slots- Suitable for rackmount applications- 3U 48HP fanless enclosure- Optional redundant CompactPCI power modules
-
product
PXI Single 8 Channel Optic Mux LC
40-852-418
The 40-852-418 8-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
9050 - 50 Module, 2-Tier Solution
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
-
product
External Transmitter
terraTX-50
The terraTX-50 is a high power field transmitter capable of delivering 50Amps to a transmitter loop, designed to be used in conjunction with a terraTEM unit. The period is controlled by the terraTEM24, terraTEM or the optional inbuilt GPS synchronisation module within the terraTX-50. The ramp and the full Tx current waveform are directly inputted into the terraTEM24 or terraTEM. This makes the terraTX-50 simple to operate, freeing up operators from inputting key system parameters into the console after each sounding.
-
product
3U OpenVPX Ethernet Switch and Multifunction I/O Board
68G5E
The 68G5E is a 3U OpenVPX board that is configured with an Ethernet Switch module (choose the ES1, 12-Port GbE Cu legacy unmanaged Ethernet Switch, or the ES2 16-Port Cu GbE managed Ethernet Switch with optional 4x 10GBASE-SR 850 nm multimode Fiber Optic interface) and provides additional support for one NAI smart I/O and Communications function module. Uniquely designed, the 68G5E provides ‘independent’ Ethernet Switch capabilities and can operate as a MFIO board end point with access via the 1...show more -
product
PXI Solid State MUX, 4 pole, 40 channel
40-680-404
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-020
The 40-297A-020 (PXI) and the 42-297A-020 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 472 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI 16x4 RF Matrix 300MHz 50 Multiway Connector With Loop-Thru
40-727-002-L
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
product
PXI 2 Slot BRIC 88x4 2-pole (2 sub-cards)
40-562A-222-88X4
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
8 Channels, RTD Measurement
RT1
The module provides 8 measurement channels, and can be programmed for interfacing to 2, 3, and 4-wire platinum RTD sensor configurations. The 4-wire mode (default) is the most accurate, providing excellent stability and repeatability. The RTD channels feature individual A/D converters and precision excitation/current drive. Programmable lead-wire compensation is provided for inherently less accurate 2 and 3-wire configurations. All RTD channels are self-aligning because each channel is automatic...show more -
product
PXI/PXIe MEMS Optical MUX, Quad 2-Channel, Single-Mode, 9/125 Fiber, LC Connectors
40-855A-442
The 40/42-855A-442 is a PXI/PXIe quad 2-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
Receiver, G12, 12 Module, With 20" Platform, For Tabletop
310104409
Receiver, G12, 12 Module, with 20" Platform, for Tabletop
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-043
The 40-297A-043 (PXI) and the 42-297A-043 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 773 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Linear Bench or Rack Mount Power Supplies Programmable, Local Control, Ultra Low Ripple/Noise
Series PAT
SERIES PAT are operationally programmable power modules that can be programmed to any level within their rated range and fully loaded at any output setting. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
product
LXI High-Density Matrix
Our LXI High-Density Modules are single and double pole matrices available in a wide range of configurations including versions with the added flexibility of dual analog bus. These high-density matrices are ideal for signal routing in large automatic test equipment (ATE) systems and are suitable for applications where a simple start-up process is required and for applications requiring control over large distances.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-018-M62.5
The 40/42-852A-018-M62.5 is a PXI/PXIe 8-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI 8 Slot BRIC 138x8 1-Pole (3 sub-cards)
40-560A-121-138X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
