Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
product
RJ45 Port Saver
#21025C
Extend the life of your tester by using the RJ45 PortSaver as your sacrificial cable. Eliminates the wear and tear from constantly plugging in and out of the tester port and minimizes the risk of damaging the RJ45 jack if the connector contacts are not crimped completely. Compatible with all Platinum Tool testers with built-in […]
-
product
Digital Non-Contact Tachometer
TACH2
UEi Test & Measurement Instruments
The TACH2 is a dual measurement mode, contact or non-contact, Tachometer that measures rotational speed using both modes. With measurements of RPMs up to 99,999 are possible, with resolution automatically changing throughout the range.
-
product
Micro Coax, Contact, ITA, RG178
610141102
Primary mating contact 610140102. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 3 GHzVSWR 1.22 @ 3 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications RG178Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Mini Coax, Contact, ITA, RG316 Double Shield
610103152
Mini Coax, Contact, ITA, RG316 Double Shield.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 1 GHzVSWR ≤ 1.06 @ 1 GhzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzDWV 1500 VDC Min.Contact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications RG316 Double ShieldEnvironmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
product
H.V. Probes
PD-20
Standard Electric Works Co., Ltd
● Measures both AC and DC voltages with digital multitester.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.
-
product
Tool, Inspection Depth Gauge, Mini Coax, ITA
910121157
Used to verify the depth setting of the center conductor of the ITA mini coax contacts.
-
product
Copper, Type T (°C) Contact
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
product
6-12V Heavy Duty Circuit Tester
1668
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems. To indicate whether there is an electrical potential at any low voltage point in the system. By using the pointed contact tip to pierce insulation on cables, it will also indicate if current is present. This can be helpful when tracing faults or add cable to a circuit.
-
product
Calibration Plates
MVTec provides precision-manufactured calibration plates to its customers. The plates are necessary to accurately calibrate a machine vision setup. MVTec’s calibration plates are available in different materials and in sizes ranging from 2cm×2cm up to 32cm×32cm. Contact your local distributor for assistance with choosing the right plate size and material for your application.
-
product
Card Edge Connectors
R600
VECTOR Electronics and Technology, Inc.
R656-2R600 series card edge female connectors for 0.062"(1.57mm) thick boards. Available in wire-wrap or solder tail type termination.Available in 30, 72, 44, 56, 80 and 100 contacts total with dual row.
-
product
CONTACT CUM NON CONTACT DIGITAL TACHOMETER
IBL-DT2236
International Biological Laboratories
This is a digital contact cum Non Contact combined, Hand Held Tachometer.
-
product
Flatness, Bow, Warp, Curvature, Glass Thickness
Standard Warp Measuring System
Optik Elektronik Gerätetechnik GmbH
Optical, non contact measurement of warp and bow of specimen with size up to (1600 x 1200) mm. The system is designed for the contactless, optical measurement of the curvature (Warp) horizontal, coated float glass substrates. For that measurement the heights on different measuring points is evaluated.
-
product
PXI Ultra High Density 64x4 2-Pole Matrix
40-533B-022
The 40-533B ultra high density matrix module is configured as 64x4 or 64x2 and is available in a choice of 1-pole and 2-pole reed relay formats. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by daisy chaining the common signals from multiple PXI modules.
-
product
Fine Pitch Probes
Fine pitch probes are spring contact probes with pitches between 0.10 / 4mil and 1.00mm / 40mil.In this pitch, direct soldering and the use of mounting receptacles is usually no longer possible. Therefore, almost all fine pitch probes are designed as double-sided spring-loaded contact probes. Fine pitch probes are installed in corresponding test sockets, which enable exact contacting of the test points. Feinmetall fine pitch probes are suitable for common components such as BGA, LGA, QFP, QFN or WLCSP. Precision and 100% quality control characterize these probes.In smaller pitches of 60 – 300µm, carrier needles (beams) are also used.
-
product
Circuit Breaker Testing Equipment
HISAC Swift
HISAC Swift - Circuit Breaker Operational Analyser is meant for checking the performance of the MV Circuit Breakers. The Analyser contains various intelligent measuring modules designed for measuring parameters such as contact timings of Main/PIR & Auxiliary contacts, Close/Trip Coil Current characteristics and Static Contact Resistance of R, Y & B poles simultaneously. The results can be directly viewed on the TFT touch screen display in graphical as well as numerical form. It is possible to print the graph on a built-in thermal printer or download record to PC for further analysis on CPLOT software. This all in one instrument is best suited for gang operated CBs.
-
product
ContactLAB Tester
The ContactLAB test platform provides fully configurable reader signal emulation for validation of ISO 7816 contact smart cards and Single Wire Protocol (SWP) USIM for NFC enabled mobile handsets.
-
product
USB-Micro Type B (Special Models) Test Connector
Test connector for USB-Micro Type B (Special Models) (5 pole) for contacting Micro USB interfaces. Application in smaller USB devices like cameras, mobile phones, radios, hard disks, etc.
-
product
Spring Probes & Hyperboloid Contacts
In-Circuit / Functional Probes, Socketless X Probes®, High Current Probes, Double Ended Probes, ATE Interface Probes, integraMate®
-
product
Dual 16x8 1-Pole High-Density PXI Matrix Module
40-520-205
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Non Contact Measurement
There is no one-size-fits-all solution for accurate measurement, and different applications require different measurement systems. At Vision Engineering, we design and manufacture a broad range of non-contact measurement systems from toolmakers’ measuring microscopes to fully automated CNC video measuring systems with optional contact measurement available. Combined with the latest metrology software solutions available, we offer the right tool for the job.
-
product
Multiple Angle Reflectometry
FilmTek 4000
Scientific Computing International
Fully-automated wafer metrology optimized for photonic integrated circuit manufacturing. Delivers unmatched measurement accuracy, with a 100x performance advantage over the best non-contact method and 10x that of the best prism coupler contact systems. Designed to enable optical component manufacturers to increase functional yield of their products, reliably and at lower cost.
-
-
product
Mechanical Testing Machine
Shenzhen Bonad Instrument Co., Ltd.
The design of our drop tester machines is divided into several styles according to the product and package sample’s size and weight. Some drop testers are specially used for small and light consumer electronics such as mobile phones, tablets, and other digital products or handheld mobile devices. And some other drop test machines can be used for the drop test on the complete package loaded with the product, even on the heavy-duty and bulky packaging cartons.Our drop test machines are designed to meet ISO, IEC, ISTA, ASTM test standards. For more information, please contact us, BONAD will provide you with professional technical consultation and high-quality testing equipment.
-
product
Test Fixtures-Assemblies
Qmax Test Technologies Pvt. Ltd.
Test Clips are available for various types of DIP ICs like 8, 14, 16, 20, 24, 28, 40, 48 & 64. These can be supplied with or without connectors and cables for interfacing to Qmax Testers. Test Pins in the clips are gold plated and engineered for good contact with the Device Under Test. It is designed for long life and trouble free operation. For easy handling the clips are provided with metal covers.
-
product
Non Contact Temperature Sensors
Non Contact Type temperature measurement involves determining temperature of object surface without direct contact with the surface. Tempsens offers both single point and area inspection model devices which are infrared thermometers and infrared camera and industrial furnace monitoring camera.
-
product
Signal, Module, Receiver, TriPaddle, 90 Series, 96 Position, w/ Right Angle Contacts
510104135
Primary mating module 510108125. (May mate with other ITA modules, as well.)
-
product
Alignment Sensors and Switches
The Touchswitch is an electro-mechanical limit switch with no moving parts, which detects tracking and misalignment problems on bucket elevators and conveyors. When a belt misaligns or a pulley moves over and contacts the sensor, the built in solid-state electronic circuitry detects the lateral force of the belt or pulley and activates a voltage free relay contact. This relay contact is used to immediately alarm and shutdown the machine.
-
product
Handheld
iSeries
Rugged and reliable, the iSeries integrates VPC contacts and modules into a compact format that can be used with VPC standard mass interconnect solutions and stand-alone applications. iSeries connectors are also available as complete cable solutions.
-
product
Passive Oscilloscope Probes
5900 SERIES
Probe Master's new 5900 series passive oscilloscope probes are available in 400 MHz & 500 MHz bandwidths. Probes are also available with readout actuators for oscilloscopes with the readout feature. The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.The probe body is made of high impact ABS. Soft molded strain reliefs at all stress points assure long cable life. In short it has been designed to offer you high performance coupled with high quality.
-
product
7 Round Pin Tractor Trailer Circuit Checker / Maintenance Kit
#8029
Innovative Products of America
Test, clean and restore 7 round pin connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 7 round connectors. Tests tractor electrical circuits Removes corrosion from truck and trailer connectors Enhances electrical contact points Extends harness life Use as a pin wear gaugePatentedKit Includes: #7865L: 7 Round Pin Tractor Trailer Circuit Checker, #8024: 7 Round Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
