Clamps
-
-
Product
Combinated Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Measure small direct and alternating currents up to 2 A with 1 mA resolution. The device measures the current indirectly via the surrounding magnetic field, so it is measured without contact when the clamp jaws enclose the current-carrying conductor (single wire).
-
Product
Current Clamps and Sensors
-
Are designed for measuring leakage current diverted towards the earth. It enables the fault to be located or anticipated without disconnecting the equipment linked. It is specially designed to detect low fault currentson power circuits.
-
-
Product
High Frequency Current Transformer Clamps
HFCT-20HD & HFCT-60HD™
-
The HFCT-20HD™ and HFCT-60HD™ are high frequency current transformer sensors designed for partial discharge detection on electric apparatus’ ground returns. Made from superior quality materials, it is designed for any environment.
-
Product
Self Testing Clamps with Visual Indication
Bond-Rite REMOTE
-
As an alternative to the standard Bond-Rite, a ?remote? version is also available. In this configuration, the Intrinsically Safe monitoring electronics, flashing green LED and battery power supply are housed inside a tough, corrosion resistant stainless steel enclosure, designed for wall mounting. An insulated stowage point, for the safe return of the clamp when not in use, is included.
-
Product
Enclosure, G12x, Front Mount, 4 Cable Clamps, 12" Depth
410112856
Enclosure
Enclosure, G12x, Front Mount, Hinged Cover, 4 Cable Clamps, 12" DepthIncludes hinged cover and 4 cable clamps for discrete wiring. When cable clamps are open- stiffener bar can be removed for installing or removing cables without unplugging patchcords from assembly.Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Enclosure, G18, Hinged Cover, 3 Cable Clamps, 7" Depth
410112664
Enclosure
Enclosure, G18, Hinged Cover, 3 Cable Clamps, 7" DepthIncludes hinged cover, handles and 3 cable clamps- allow a max. cable bundle of 1.59 sq. inches per clamp. ITA strain relief plates. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Basic Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Are ideal for current measurement in electrical systems and control cabinets, since only single wires are guided through the clamp jaws for contact-free current measurement and no electrical connections have to be disconnected. This method also enables measurements of very high currents, which would overload any standard multimeter if connected directly.
-
Product
AC Mid-Size Clamps
-
can enclose conductors up to (50mm) 0.968 inch and measure currents from 100mA to 1200A*. They are a reliable and economic solution for common applications.
-
Product
Enclosure, G12, Front Mount, 4 Cable Clamps, 6"x 18" x 12"
410114014
Enclosure
Enclosure, G12, Front Mount, 4 Cable Clamps, 6"x 18" x 12"Includes 4 cable clamps on the back end that eliminate the need for strain relief. When in open position- cable clamps permit removal of the stiffener bar so that installation or removal of cables may be performed without unplugging patchcords from the assembly. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
-
Product
Multimeter Clamps
-
The ideal tool for detecting and measuring the leakage currents flowing to earth.The versatile clamp also offers all the functions of a multimeter clamp.In addition, the clamp is equipped with an RMS converter to ensure that the measurements remain accurate even in the presence of distorted signals.
-
Product
EM Clamps
-
The EM Clamp or a Bulk Current Injection Probe (BCIP)can be used for IEC/EN 61000-4-6 tests on ports/cables for which no Coupling/Decoupling Network (CDN) is available.
-
Product
Probe “Socket” Clamps
LCP-S12
-
A simple and cost-effective option for mounting Small-aperture Probes in the probe plate. A Socket Clamp tool is needed for insertion and removal of the clamp in the probe plate
-
Product
True RMS Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Current clamps are ideal for current measurement in electrical systems and control cabinets, since only single wires are guided through the clamp jaws for contact-free current measurement and no electrical connections have to be disconnected. In addition, this model has extensive multimeter functions for voltage, resistance, frequency, capacitance and temperature measurement.
-
Product
Digital Clamp Meter
MT87
-
Wenzhou Zhengyuan Electronic Co., Ltd.
AC current measurement without interrupting the circuit.
-
Product
AC Clamp Meter
2940 CL
-
Standard Electric Works Co., Ltd
Pocket size. 4000 counts. Full automatic measurement (Voltage measurement, Current measurement, Resistor measurement). Data hold function. Continuity check. Diode measurement. Select function. Low battery indication. Auto off function. Flashlight (Auto off in 1 minute).
-
Product
IEC60068-2-75 Spring Impact Hammer
-
Shenzhen Chuangxin Instruments Co., Ltd.
Adjust the impact severity by rotating the knurled cap until the desired energy- value is displayed. Pull the knob slowly out of the device until it locks in place. If moved too fast, the clamp may skip its arrester and will lock at its way back when the pulling-force declines. Hold the device horizontally at it’s housing tube and press the (black) release cone to the specimens plane of impact. The strike is automatically released when the release force threshold is reached.
-
Product
Bite Test Clamp
G201A29-30
-
Simulates a child biting the accessible area of child-related products. The part of the child-related products being tested is placed in a bite test clamp & a specified force is applied for a specified period. The child-related products is then tested to ascertain whether or not any hazards result from the bite test such as sharp points/sharp edges/small parts.
-
Product
68-Pin SCSI Micro-D Female Connector Block
40-965-068-F
Connector Block
This connector block provides a simple method of connecting to 68-Pin SCSI Style Micro D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
Wireless Connectivity AC / DC Clamp Meter
MS-W366D
-
This is a external wireless connectivity Digital Clamp Meter integrated with AC / DC hall effect sensor / 6000 Count, True RMS, auto and manual measurement.
-
Product
Riverboat SP
-
Teledyne Marine RD Instruments
The Riverboat SP is the top choice for deployment of the Teledyne RDI StreamPro acoustic Doppler current profiler. Upgrade from the standard StreamPro float to the more stable, rugged and fully corrosion-resistant tethered boat. The Riverboat SP makes safe, easy measurements of discharge in relatively slow and fast flowing waters. Made of unbreakable polyethylene, the Riverboat SP is strong and can handle tough deployment conditions. The standard boat configuration fits a TRDI StreamPro ADCP, and the latest instrument clamp is suitable for the StreamPro with or without an internal compass upgrade.
-
Product
Configurable CAN FD Modules With A Focus On Digital I/Os
PCAN MicroMod FD Digital 1&2
-
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The main boards PCAN-MicroMod FD Digital 1 and 2 focus on digital inputs and outputs, which are provided with the appropriate protective circuit. The digital outputs of Digital 1 are equipped with low-side switches and those of Digital 2 with high-side switches.
-
Product
Clamp Meter, Auto, True RMS, 1 kA AC, 600 V AC, 600 V DC
72-9485
-
A professional digital clamp meter that is perfect for any industry. Measures AC/DC voltage, AC/DC current, Resistance, and Frequency.
-
Product
CAT IV 600 A TRMS Navigator Clamp Meter
ACD-50NAV
-
ACD-50NAV clamp-on power meter offers AC current measurements to 600 A, AC/DC voltage to 1000 V, and wide jaws to accommodate large conductors. This clamp-on multimeter is ideal for industrial power monitoring and verifying system conditions.
-
Product
3.5 Digit Handheld Clamp Meters
U1190 Series
Digital Multimeter
Keysight’s U1190 Series clamp multimeters incorporate features to help you work more conveniently and safely. Housed in robust cases, these ergonomic handheld digital multimeters (DMM) fit comfortably in the palm of your hand and let you select functions with just a thumb press. A Keysight clamp multimeter is different from most other clamp multimeters because it also features handheld DMM functionality.
-
Product
68-Pin VHDCI Connector Block, Female With Backshell
B068VFR-6F-0A
VHDCI Female Connector Block
This connector block provides a simple method of connecting to high density 68 Way VHDCI connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
Oscilloscope Module, AC/DC, Clamp Meter Lead, Digital Multimeter
72-9180
-
The 72-9180 is an AC/DC Clamp Meter Leads, use almost any DMM as a clamp meter for current testing up to 400A and current displays as an easily translated voltage reading.
-
Product
Torque Test Kit
G201A11-16
-
To determine whether components of child-related products can be removed by a certain torque force. A torque-measuring device is used in conjunction with a torque clamp to record the applied force. Any projection, part or assembly of a child-related products that a child can grasp with at least the thumb & forefinger or the teeth shall be subject to the torque test.
