TWT Amplifiers
generate high power RF signals. Also known as: Traveling Wave Tube Amplifiers, TWTA
See Also: Microwave Amplifiers, Traveling Wave Tube Amplifiers, TWTA
-
Product
Hybrid Amplifiers
LNA
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of hybrid amplifiers cover a frequency range of 10 kHz to 6 GHz. Each amplifier is designed to be unconditionally stable and have excellent cascadability. Our amplifiers are designed using thin film technology and are integrated components that include internal DC biasing circuitry, allowing them to maintain excellent electrical performance over the 55˚C to 100˚C range. Hermetically sealed and screened up to space level, these amplifiers are ideally suited for hi-reliability and mission critical applications.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Variable Gain Amplifiers
-
50 dB Gain, 14 dBm P1dB, 100 MHz to 18 GHz, Rack Mount, Variable Gain Amplifier, 6.5 dB NF, SMA
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
-
Product
Automotive Audio Power Amplifiers
-
ST is the recognized leader in automotive power amplifiers. Our car audio amplifiers provide the traditional clean and powerful sound that users have come to expect, as well as all the protection and safety features needed to make our devices robust in an automotive environment.
-
Product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3
-
The AAF-3 is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier ISA bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
Product
Solid State GaN (Gallium Nitride) Amplifiers
-
Fairview Microwave’s solid state GaN (Gallium Nitride) power amplifiers (also called SSPAs) feature broad frequency bands ranging from 30 MHz to 7.5 GHz and very high gain levels from 43 to 60 dB. These GaN SSPAs also show impressive harmonic response (-15 to -20 dBc) under worst case conditions. Saturated output power levels range from 10W to 100W with 20% to 35% Power Added Efficiency (PAE). All of our high power solid state GaN amplifiers from Fairview have internally regulated single voltage supplies. Our GaN SSPAs are designed to withstand environmental conditions such as humidity, altitude, shock and vibration with an operating temperature ranges from -40°C to +85°C. Some models are also equipped with integrated heat sinks and cooling fans. Most designs are EAR99.
-
Product
Broad Band Amplifiers
-
Broad band amplifiers (A.K.A. wide band) from Fairview Microwave provide amplification for radio frequencies in broadband. Our broad band amplifiers applications include: military / defense, test instrumentation, EW/ECM, radar, satcom, telecom, microwave radio and various industrial RF, microwave and millimeter wave applications. Fairview broad band amplifiers have a maximum frequency as high as 18 GHz depending on the amp configuration.
-
Product
Low Noise, High Performance, FTTP High Power Multi-port Optical Amplifier with a Gain Spectrum Band
MX5800 Series
-
Each output port for the optical amplifier has built-in high performance CWDM. Every external up-link optical port of the optical amplifier can conveniently connect with an OLT. Each of the 1550nm (CATV)’s output optical ports will multiplex 1310/1490n’s data stream from an external OLT, reducing the quantity of the components and improving the performance and reliability of the system.
-
Product
Femtosecond Multipass Ti:sapphire Amplifier
MPA 50
-
MPA 50 is a multipass Ti: sapphire amplifier based on a two-mirror confocal design and containing a pulse stretcher, a pulse compressor, a pulse picker, synchronization electronics, and the Faraday isolator.
-
Product
Dual Channel HV Amplifier with Phase Inverter
A400DI
-
This unit contains two independent A400 amplifiers that share common ground reference and power supply. Please see A400 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase. Connecting a load between the outputs effectively doubles the amplitude range. Please note that the load cannot have any connection to ground.
-
Product
Power Amplifiers
-
In this product category you find highly linear power amplifiers for digital and analog data transmission, power amplifiers for CW applications and for laboratory use, which stand out due to its liability, robustness and long-term availability and which are based on the semiconductor technologies which are actually available on the market.
-
Product
Transconductance & Transimpedance Amplifiers
-
Measurements International Ltd.
0 to 100 Amps – AC, 0 to ± 100 Amps – DC, Voltage Compliance ± 5 Volts, IEEE-488 Interface, Resistive, Capacitive, Inductive Loads.
-
Product
RF Amplifier
SA801H
-
Hangzhou Softel Optic Co., Ltd.
SA801H indoor unidirectional user’s amplifier is special designed for the last “1km” of the CATV bidirectional transmission network. It adopts CATV dedicated RF modules (SOT-115 packaged), has good indexes, low power consumption, high reliability and excellent cost performance. It is suitable for the small and medium sized CATV transmission network.
-
Product
Low Noise Op Amplifiers (≤ 10nV/√Hz)
-
Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.
-
Product
Amplifier Dyno
AD-1
-
The AD-1 Amplifier Dyno is a tool that is designed to be used any place an amplifier exists. It can be used in a lab or production line to test true amplifier power output, quickly and easily. It is simple menu driven, does not require a computer, and cannot be cheated as the load banks are internal. It can be used in an automotive audio install shop to test true amplifier output while the amplifier is installed in the customer's vehicle.
-
Product
RF & Microwave Broadband Amplifiers
-
SHF Communication Technologies AG
SHF has been active in the design and production of broadband RF-microwave amplifier. The outstanding performance makes our amplifiers suitable for a wide variety of applications in R&D. This includes not only optical communications, but also satellite communications, high-speed pulse experiments, data transmission, quantum communication, radar and antenna measurements.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
-
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
High Voltage Amplifier
HA-800
-
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
Product
Amplifiers
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
IEPE Signal Conditioning Amplifiers
-
Although IEPE (Integrated Electronics Piezoelectric) sensors is not a new technology there are a wide variety of applications where the measurement instrumentation is not configured with IEPE signal conditioning built in. In these situations it is necessary for the IEPE supply to be provided by an external source. Usually this type of instrument will also provide th user with the option to add gain to the signal being conditioned. The Kemo range of IEPE signal conditioning instruments can be used as stand alone conditioners/amplifiers are many of them can also be integrated with filters.
-
-
Product
40~860 MHz Trunk Hybrid Amplifier
AS 1616
-
Hybrid Amplifiers used in Trunk and branch lines specially designed to serve the needs of cable systems with very Long Trunk Cables. They are in Aluminium Housing providing maximum heat dissipation and have RFI Shielding. They incorporate superior quality Hybrid IC Module to obtain excellent features.- Frequency Range: 40 ~ 860 MHz- Mains cum Power Pass- Output Level: 102 dBµV- Level Flatness: ±0.75 dB- 32 dB Gain (40 dB Optional)- Optimum for Trunk Distribution- Superior Quality Hybrid IC Module- Hybrid IC Protected- Voltage Selection LED - for Easy Selection
-
Product
Low Noise Super Wide Band Amplifiers
WBA Series
-
WBA series low noise amplifiers have the octave bandwidth from MHz to GHz. With super low noise figure and exceptional low VSWR, WBA series LNA achieves exceptional gain flatness accross octave or multi-octave bandwidth.
-
Product
Shortwave Power Amplifier
OM4001HF
-
The OM Power model OM4001HF is designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. It is equipped with a two ceramic tetrodes FU-728F.
-
Product
DVB-T Amplifier Module
-
The COMM-connect DVB-T Amplifier Module is a very versatile module, for use in multiple applications, including driving High Power amplifiers or stand alone Gap-filler. The amplifier covers both VHF & UHF bands, and can be combined with several COMM-connect filter options.
-
Product
Fiber Optic Sensor & Amplifier
FG-1300 | FS-5500/FS-540
-
The FG-1300 is a non-contact type high-performance amplifier that emits red light from LED to a rotating object, and detects the variation of the reflected red light amount.This amplifier is used in combination with an exclusive detector FS-5500*/FS-540 Fiber Optic Sensors which has adopted environment resistant design. The glass fibers are covered with flexible stainless steel tube for rotation measurement in limited space.
-
Product
Solid State Broadband High Power Amplifier 1900 - 6000 MHz / 200 Watts
2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. for EMC, RF Product Test, Communications and Electronic Warfare applications.
-
Product
Single Channel High Voltage Linear Amplifier
F10A
-
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
