Genrad Fixtures
See Also: Teradyne Fixtures
-
product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 230 x 175 mm (wxd)
CMK-06
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Fixture and Software for Open/Leak Inspection
In addition to jigs and fixtures for probing conductors and electrode pads, NIDEC-READ provides specialized software for test point selection and log analysis.
-
product
Wireless In-Circuit Test Fixtures
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
product
EBIRST 50-pin D-type Verification Fixture
93-005-101
The 93-005-101 50-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Lamp & Fixture Wiring Tester
GT3110GAM LAMPCHEK
LampChek indicates the lamp and fixture continuity.
-
product
USB-C® – USB 2.0 Plug HS SQ Test Fixture
AUT17094
This product is designed for USB-C USB2.0 Receptacle Host Electrical Test.
-
product
Manual Fixture Kit
230372 – CMCSK-03-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
EBIRST 200-pin LFH Verification Fixture
93-002-101
The 93-002-101 200-pin LFH Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions.. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Incremental Length Gauges For Measuring Stations And Multi-gauging Fixtures
SPECTO series
*High system accuracy: ±1 µm*Very rugged design*Compact design for limited installation space*Various plunger actuation possibilities*Highly durable ball-bearing guide*Measuring range of up to 30 mm*Interfaces: 1 VPP, TTL*Protection rating of up to IP67
-
product
Automatic Fixture Removal Software
S97007B
Automatic Fixture Removal (AFR) software is used to remove the effects of the fixture used to test coaxial connectors, which is required to make accurate measurements on the device
-
product
Fixtures, Programming & Test Services
Comware Technical Services, Inc.
Fixtures and programming services are available for Agilent, GenRad, and Teradyne testers. Working from CAD data, a program can be created in only a few days allowing for fast and cost effective testing of your products. Engineering services are available for fixture revisions or repairs.
-
-
product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester.
-
product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 197 x 114 mm (wxd)
CMK-05
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Audio Panel/Amplifier Test Fixture
TA-200
The Model TA-200 test panel was designed to allow Avionics shops the capability to test and troubleshoot both today's new generation audio panels as well as the standard audio panels of the past. The testing of these panels over the years has always proven to be a very time consuming job for most shops because of the limited capabilities of any past test panels.
-
-
product
Wave Profiler Fixture
KIC® Wave Surfer™
The KIC Wave Surfer is a self-contained system that provides critical data on wave solder machine set up and performance. Used in conjunction with your SlimKIC 2000 and the KIC 2000 software, you can ensure your wave solder machine is set up and performing properly.
-
product
RF Chamber Fixtures
- 12” W x 12” D x 8” H internal dimensions- RF mechanical chamber can fit various wireless and Bluetooth products- test either commercial or consumer
-
product
Vacuum Test Fixtures
Series 63
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
product
Stand-Alone Test Fixture
MA 2012/D/H/GR2270/71
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,00 kg
-
product
Debug Fixture
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
product
EBIRST 9-pin Male D-type Termination Fixture
93-003-103
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
RF/Wireless Test Fixtures
Test‐Head Engineering develops and manufactures RF Test Fixtures which allow the testing of RF and Wireless modules and components.
-
product
EBIRST 104-pin D-type Verification Fixture
93-022-101
The 93-022-101 104-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
GPS/FMS Universal Test Fixture
TA-3000
This panel was designed to give the avionics shop the capability to test and troubleshoot many of the GPS, GPS/COMM and FMS units on the market today. Breakout jacks are provided for both analog and digital signals that need to be monitored or simulated. A data port update jack is provided as well as Arinc 429 and RS232 loopback switches. Switches for Gillham altitude are provided as well as fuel flow adjustments. An array of annunciators and configuration switches are also provided to verify those outputs and inputs. Optional UUT configuration overlays also availabl
-
product
Custom Fixtures
Joule mechanical design and manufacture capabilities allows us to create other custom projects to meet your test needs. Joule can design burn-in racks, jigs and stand-alone test station.
-
product
INTERFACE TEST FIXTURE KITS
GENRAD 2270
Test-X GR Series CAM/TRAC® kits offer the same "Z" axis motion as the standard CT Series with the advantage of interface compatibility.Standard features include locking handle assembly, 3/8" FR4 probe plate, and 12 position I/O block interface..
-
product
EBIRST 23 X SMB Verification Fixture
93-011-101
The 93-011-101 23 x SMB Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
TRUE Z-AXIS CAM ACTIVATED TEST FIXTURE KITS
The Cam Press is designed to provide precise, bed-of-nails contact, in a production test environment. Durable aluminum and steel construction and precision bearings insure accuracy and repeatability sufficient to contact test points as close as 10-mils center-to-center.
-
product
Becker Transponder Test Fixture
TA-3400
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
