-
product
Digital Circuit Tester 3-30V
29050
The probe is insulated to prevent the possibility of shorting the side of the probe to other components. 47" cord and heavy-duty alligator clamp for secure connections.
-
product
Add-On Autopan Board
AP1
An add-on board that provides an autopan function to any AC, fixed speed pan and tilt head fitted with limit switches. It functions by monitoring the current flow to the CCTV panning motor and selecting the alternate motor whenever the current ceases (i.e. limit switch is activated). This facilitates simpler wiring to the panning head without the need for additional switches or other components to be fitted to the head.
-
product
Wavelength and Power Meter
WPM-1NM
•Wide range Wavelength Meter– Auto λ detection from 1270nm to 1610nm– Auto power calibration & display•FTTx/PON Wavelength Meter– 1310/1490/1550nm auto λ detection– Auto power calibration & display•Optical Power Measurement– Optical network power measurement– Power measurement for system & module•Insertion Loss Measurement– Optical network & component IL measurement– IL measurement for CWDM 16-wavelength•Smartphone Interface– Communicates with smartphone via bluetooth– Smartphone application software
-
product
Adapter/Stainless Steel
WADP-NFNF-BH
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
EV And Pack/Module Tester
Discover the Series 8500, an innovative and fully automated test system engineered to evaluate the performance of Electric Vehicle (EV) components, Energy Storage batteries, Modules, and Packs in real-world conditions. This high-specification system not only delivers accurate results but also allows the energy produced during discharge to be returned to the electrical grid.Using Maccor’s standard fully featured battery test software, the Series 8500 can perform virtually any type of battery test including FUDS, SFUDS, DST etc. for electric vehicle batteries and standard cycling tests for energy storage devices.
-
product
Circbord
3677-6
VECTOR Electronics and Technology, Inc.
3-Hole Solder Pad. Holes are not plated-thru. Single-sided with no etch or plating on reverse side. Unrestricted component placement.
-
product
Eddy Current Flaw Detector
US-525M
United Western Technologies Corp
The US-525M multi-channel eddy current testing instrument is a rugged industrial rack-mounted instrument offering multi-channel testing, integral digital strip chart, as well as Ethernet control and data transfer to meet your in process testing requirements. This instrument offers up to eight channels, with a frequency range of 20 Hz to 10 Mz, a high signal-to-noise ratio, a bright 12-inch diagonal color LCD flat-panel screen, and data storage of 32 Gig. It offers input/output (I/O) capability, USB and Ethernet connectivity, as well as three discrete alarm gates with independent outputs per channel. for your on-line bar, tube, wire and specialty component testing needs.
-
product
Medium Kelvin Clip Lead
16089B
Measure odd-shaped components that you cannot measure using conventional fixtures
-
product
Resistance Meter
RM3542A
High-speed resistance meter ideal for automated lines; compatible with super-small electronic components • Testing source: DC • Fastest measurement time: 0.9 ms • Minimum integration time: 0.1 ms • Finest resolution: 0.1 μΩ
-
product
X-ray Inspection Of PCB Boards And More
The RTX Series
Glenbrook’s RTX Series of modular, real-time systems include models designed to meet a variety of production requirements including circuit board components. Numerous options make it easy to customize any RTX model to your specific application. All hardware and software elements are fully compatible to ensure the continued value of your equipment.
-
product
Datapaq Oven Tracker Systems
The Datapaq Oven Tracker Systems from Fluke Process Instruments are designed to provide comprehensive thermal profiles for applications such as powder coating, paint curing, component supply and general paint, powder and e-coat OEM applications up to 400°C. With our thermal profiling solutions, you can monitor your whole process from within the oven and gain meaningful information through automatic reporting, which turns raw data into meaningful analytics that showcase if optimal temperatures are met to ensure high-quality results.
-
product
New Link system Control and Image Capture Software
New uncluttered and intuitive user interfaceLive display of current status for easy monitoringFull control of heating and cooling rate, limit and hold time of up to 100 rampsRow by Row control of Vacuum, Humidity, Tensile Force and Shear modes controllable and synchronised with TemperatureParameters of connected Linkam sensors displayed and stored - e.g. Vacuum, Humidity, Force, XY position and Pressure (dependent on connected stage type)Real Time chart of temperature and other measured paramete...show more -
product
Pen Type Leeb Hardness Tester
TIME®5100/5102/5104
Beijing TIME High Technology Ltd.
Pen Type Hardness Tester TIME®5100/5102/5104 is economically priced and suitable for quick hardness testing on metal materials, especially on-site hard testing of large, non-transportable components.
-
product
Infrared T1 3/4 LED
350-00003
T1 3/4 Infrared light emitting diode, for breadboard or through-hole projects. Used with the LED Standoff and LED Light Shield to build the IR Transmitter Assembly (#350-00017). Frequently used with the IR Receiver for object detection and autonomous robot navigation, this is a compatible replacement wherever an Infrared LED is found in any of our Education Kits Components Listings.
-
product
Low Phase Noise Amplifiers
Pasternack's low phase noise amplifiers cover select frequency bands ranging from 1.5 to 18 GHz with residual phase noise levels as low as -180 dBc/Hz @ 10 KHz offset. Additional performance specs include small signal gain ranging from 9 to 14 dB, with typical noise figure of 5.5 dB. Psat levels for these amplifiers range from +16 to +25 dBm with Output IP3 levels as high as +34 dBm. All models feature single DC voltage supplies and input/output RF ports are internally matched for 50 ohms with...show more -
product
LATCH UP Tester
Tokyo Electronics Trading Co., Ltd.
The purpose of Latch-up testing on your components is to verify their robustness against overvoltage/ overcurrent events during their operation.
-
product
Fiberoptic Repeaters
*Cost effective task specific Fiber Optic Solutions for Satellite Radio and GPS over Fiber*End to end solutions complete with RF to Optical and Optical to RF component*Flexible powering options including DC over hybrid cable, local 48 VDC and AC*Utilizes industry standard fiber cables and connectors
-
product
Optical Fiber Analysis System
2200
The 2200 Optical Fiber Analysis System provide high-speed characterization of the spectral loss of single-mode and multimode fibers. Configurations include the 2200 for single-mode fibers, the 2210 for both single-mode and multimode fibers, and the 2220 designed for single-mode fiber ribbons. All three systems employ unique fiber preparation and signal processing techniques, which deliver both the measurement performance and the testing throughput required by high volume fiber, cable and component manufacturers. Options are available for mode field diameter and multimode numerical aperture measurements.
-
product
RF Power Generators
MKS RF Power Generators provide reliable solid state power for thin films processing equipment. They are vital components of semiconductor fabrication systems, which produce the integrated circuits (ICs) or chips required by modern computers and electronic equipment. MKS RF Generators, combined with our Impedance Matching Network and our V/I Probe form a complete RF Delivery System.
-
product
Backlights for Machine Vision
Backlighting is one of the most important components of machine vision systems; it must provide the required luminous flux, response speed, area and duration of exposure. Our experience in machine vision systems led us to the need to develop an LED backlight module for flash operation.
-
product
Smartcard Interfaces
ST offers complete analog interfaces for asynchronous 1.8 V, 3 V and 5 V smartcards. They can be placed between the card and the microcontroller with only a few external components to perform all supply protection and control functions. Main targeted applications are smartcard readers for set-top boxes, IC card readers for banking, identification and pay TV.
-
product
2-kbit 12C EEPROM for Fixture Coding
FXA-101 I2C EEPROM
The FXA-101 is a 2-kbit serial I²C bus EEPROM used for identification of systems components. With it’s DIP switch it’s easily addressable. The FXA-101 may be glued directly to the appropriate component or inserted into a UMK housing from Phoenix Contact and installed on a DIN rail.
-
product
Partial Discharge Tester
19501-K/19500
Chroma 19501-K partial discharge tester combines hipot test and PD (partial discharge) detector functions in one instrument. The device is capable of a maximum 10kV AC output with leakage current measurement range of 0.01uA and a minimum partial discharge detection of 1pC. The tester is specifically developed to test high voltage semiconductor components and high insulation materials.
-
product
Hand Held Metal Detectors
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
Designed to detect suspect items that contain metallic components, such as weapons or illicit contraband.
-
product
Software
Interface Analysis
Surface-mount components warp during the reflow process, and the area where they attach also changes shape during assembly. This interface between components is where solder, paste, and gaps created due to thermal expansion combine to create 100% good products, or defects such as Head-in-Pillow, Shorts, and Opens. Fully understanding that critical interface between surfaces is more important than ever.
-
product
SPICE software for Opto-Electronics
OptiSPICE is the first circuit design software for analysis of integrated circuits including interactions of optical and electronic components. It allows for the design and simulation of opto-electronic circuits at the transistor level, from laser drivers to transimpedance amplifiers, optical interconnects and electronic equalizers.
-
product
Magnetic-Inductive Testing
MAGNATEST® Product Family
Foerster Instruments, Incorporated
The MAGNATEST product family is used for the non-destructive testing of metallic materials for magnetic and/or electrical properties. The test instruments are used in the automotive and aviation sectors as well as in the production of semi-finished products. The focus is on testing components relevant to safety such as brake discs, or ball pins and functional components such as camshafts and drive shafts, pivots and piston pins. Typical test tasks include hardness checks, material differentiatio...show more -
product
Atlas DCA Pro Advanced Semiconductor Analyser
DCA75
The DCA75 is a great instrument for identifying and testing a wide variety of semiconductor components. Just connect any way round! The DCA75 will perform the following:*Display component type (such as N-CH MOSFET, darlington transistor etc).*Display component pinout (such as drain, source, gate etc).*Display detailed parameter measurement.*Plot characteristics curves on your PC.
-
product
Power Supplies
A power supply is a component that supplies power to at least one electric load. Typically, it converts one type of electrical power to another, but it may also convert a a different form of energy - such as solar, mechanical, or chemical - into electrical energy. A power supply provides components with electric power.
-
product
Task Factory
Save time managing tedious data warehousing ELT/ETL tasks *60+ prebuilt SQL Server Integration Services (SSIS) components to accelerate ETL processes *Optimized for SSIS to ensure fast performance of data-centric applications *Connect to dozens of data sources, including REST-enabled sources
