Emulator Adapters
-
-
-
Product
Interface Test Adapter
ITA
-
Circuit Check is focused on the military and aerospace market. Our solutions are delivered according to a rigorous set of test requirements and quality metrics. The Circuit Check staff of engineers follow a defined Project Management process to control the project deliverables,manage the scope, and meet the quality needs for in-field serviceability and test system longevity.
-
-
Product
TAP Adapter for Corelis JTAG Controllers
Low Voltage Adapter
Controller
High technology, energy efficient, and small form factor products push JTAG interfaces to the limits; low power and high performance means low voltage, high speed, and high drive requirements. Building specialized interface circuits on product Printed Circuit Boards (PCBs) is inconvenient and costly—an out-of-the-box, external solution is needed.The Corelis Low Voltage adapter is an add-on accessory that provides existing scan controllers with an active, plug-in interface to access low voltage scan chains, without sacrificing performance.
-
Product
External Contact Adapter
DT141
-
This MicroLog sensor monitors Reed Relay contacts and switch status (open/closed), to identify the correlation between phenomena such as temperature change and door status.
-
Product
Scienlab Dual-Range Regenerative AC / Grid Emulator, 600 / 1200 VAC, 63 / 32.5 A, 90 KW / 135 KVA
SL1215A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
D.V.A. Adapter
640
-
*Read peak volts on CD ignition coils with your existing digital multimeter *New, completely redesigned unit is half the size of the previous adaptor *Adapts standard digital multimeter into peak reading voltmeter *High quality test leads with alligator clips are incorporated into the adaptor
-
Product
Accessories: Intermittent Fault Emulator
-
The Intermittent Fault Emulator (IFE) is the solution. The IFE enables manufacturers, suppliers and operators of any Intermittent Fault Detection (IFD) tester to demonstrate and verify its capabilities to detect and isolate intermittent faults.
-
-
Product
Adapter, 1.0 mm (m) to 1.85 mm (f), DC to 67 GHz
11921G
-
The Keysight 11921G precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
Product
Base Station Emulator
SUTP 5018
-
Designed to create a custom cellular environment to serve testing and characterization needs. The combination of high power, real-time computing and the software defined radio platform enables this instrument to create your own cells for testing in a compact size and cost-efficient way.
-
Product
Ethernet Cable Emulator
-
Upon different commands, it can simulate different network cable lengths, including 3 Modes: Bypass, Short, 100M. It can be used independently or jointly with other devices.
-
Product
Adapter, 2.4 mm (f) to 3.5 mm (f), DC to 26.5 GHz
11901B
-
The Keysight 11901B is a 2.4 mm female to 3.5 mm female, metrology-grade adapter with dc to 26.5 GHz operation.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (m), 75 to 110 GHz
W281D
-
The Keysight W281D is a 1-mm male to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281D is used with the Keysight 8510XF systems.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (f), 75 to 110 GHz
W281C
-
The Keysight W281C is a 1-mm female to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281C is used with the Keysight 8510XF systems.
-
Product
CAMAC To NIM Power Adapter
-
Power adapter to use a NIM module within a CAMAC crate. Provides all 6 voltages to the NIM module. Available also in a versions with 12V DC-to-DC converter for CAMAC chassis without +/-12V.
-
Product
PC COM Port Adapters
-
These adapters allow PCs with one or more standard serial COM ports to monitor serial data. For adapters for PCs with only USB ports.
-
Product
NI-5741, 16-Bit, 1 MS/s, 16-Channel Signal Generator Adapter Module for FlexRIO
782864-01
Signal Generator
The NI‑5741 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs and general-purpose digital input and output lines for system stimulus and control. The NI‑5741 is ideal for applications requiring high-channel density and the power of a user-programmable FPGA. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the NI‑5741, you must pair it with a compatible PXI FPGA Module for FlexRIO.
-
Product
Manual Test Adapters
-
Manual test adapters (MA) from INGUN are available in several series and series, which differ in terms of use, maximum permitted contact force, parallel stroke, size and service life.
