Active Filters
Require power to operate, using active devices and passive components in a frequency-selective network, only passing certain frequencies.
-
Product
FPGA Impulse Response (FIR) Filter Fo Gage Digitizers
eXpert / Finite Impuls Response (FIR)
-
The onboard FIR Filtering eXpert FPGA DSP feature is a powerful method for removing unwanted signal features (like noise) and emphasizing signal features of interest.
-
Product
High Impedance Active Probes
12C
-
A high speed, high input impedance active probe for measuring the internal node voltage of integrated circuits. The input is 1 megohm shunted by 0.1 pf and the rise/fall times are 0.8 ns. This instrument has full dc capability and can be used with any oscilloscope. The Model 12C was specially designed so that when used in conjunction with a high input impedance oscilloscope, signal attenuation is 10:1 and with a 50 Ohm input, signal attenuation is 20:1.
-
Product
Filtered DC Interface Module
-
DC modules for RF Test Enclosures eliminate conducted and radiated interference, while providing a source of DC power.
-
Product
Active Probe, 5 Hz to 500 MHz
41800A
General Purpose Probe
The Keysight 41800A Active Probe provides high input impedance from 5 Hz to 500 MHz. The Keysight 41800A is a valuable tool when used with a network and spectrum analyzer for circuit signal analysis.
-
Product
Low Noise Filter Adapter
PX0107A
Adapter Module
The PX0107A converts Dsub25 outputs to five SMB outputs with the low noise filtering capability down to 25 μVrms (20 MHz). It supports the Keysight M9614/15A.
-
Product
Wide Band Filters (multi-octave)
HF-ERF™ Series
-
The HF-ERF™ is an internally switched 3‑band, low cost, miniature, high performance tunable filter. The HF-ERF™ was designed to have the best insertion loss and Q in the smallest package possible, 2.0” x 2.78” x 0.6”. All HF-ERF™ filters are fully tested and aligned by Pole/Zero for convenience and ease of use. Both SPI and Parallel control interfaces are available in one filter. Modified variants are available upon request.
-
Product
Low-PIM, High-Power Filter Solutions for Monitoring Broadband Emissions
-
Enables monitoring of PIM to 13 GHz; 100W CW and 1KW peakNear-end monitoring: Carriers rejected -90dB by the notchtravel through the bandpass filter to the low PIM termination.Far-end monitoring: Carriers rejected -90dB by the highpass,IM products passed are monitored by the spectrum analyzer.
-
Product
High Impedance Active Probes
28 AND 29
-
Designed to serve the needs of integrated circuit engineers working in the most advanced high speed, submicron, MOS technology. These high frequency instruments include the attractive features of the Models 18C and 19 including full dc capability, negligible dc current drain, and extremely low input capacitance. In addition the frequency range of the Models 28 and 29 has been extended to a full 1 GHz.
-
Product
Mid-Range Gas Filter Correlation CO Analyzer
Model N300M
-
Teledyne Advanced Pollution Instrumentation
The Model N300M is a microprocessor-controlled analyzer used to determine the concentration of carbon monoxide (CO) in a sample gas. The analysis method is based on the Beer-Lambert law.The N300M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure.
-
Product
Narrow Band Filters (Single Octave)
IMF™ Series
-
The Integrated Microwave Filter or IMF™ Series introduces accelerated tuning speeds packed in a very small, lightweight filter, providing maximum sensetivity and improved system performance for cleansing your ESM environment. Designed for the military radar market, specifically Active Electronically Steered Arrays (AESA) Radars and Phased Array Radars but compliment a broad range of applications such as; Commercial, Tactical & Military Communications, RF Front Ends (RFFE’s), SATCOM-on-the-move (SOTM), along with Electronic Warfare & Radar applications.
-
Product
Differential Active Probe, 500 MHz
DP0011A
Signal Probe
The Keysight DP0011A is the 500 MHz model of the DP001xA Series differential active probes. These probes provide the superior general-purpose differential signal measurements required for many of today’s high-speed power-related measurements such as motor drives, automotive differential bus measurements, and high-speed digital system designs.
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS1000
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Active Network Assessment and Monitoring Platform
Hawkeye
-
Keysight Network Applications and Security
Network performance and user experience are critical aspects of your business. It is vital to understand customers’ perception of your website, application, and network services. NOT knowing impacts your revenue stream. Ixia’s Hawkeye continually measures network performance and service status. If there is an issue, Hawkeye helps you identify it, quantify it, and ultimately resolve it – before your customers experience it.
-
Product
Extreme Temperature Active Probe, 1.5 GHz
N2797A
Oscilloscope Probe
Testing devices over extreme temperature ranges is quite common these days. The N2797A single-ended active probe is the industry’s first low-cost high input impedance active probe with rugged probe tips for environmental chamber testing of ICs and devices. It gives the ability to probe signals at drastic temperature swings ranging from –40 °C to +85 °C. The probe provides 1.5 GHz of bandwidth and a 2 m long cable.
-
Product
Capacitor for AC Filtering
PECA4 (690V)
-
Lifasa - International Capacitors, SA
These capacitors are especially suitable for applications where high levels of AC voltage are required. The design of this series has been optimized for the manufacture of high performance AC filters for compensation equipment with high pollution such as UPS or wind turbines.
-
Product
Wideband Active Load Pull Export Control
S94573B
-
The software enables power amplifier distortion measurements under varying load conditions that are controlled across the entire modulation bandwidth. When design verification and robustness evaluation require testing the device away from the optimum loading condition, this application provides powerful insight into device performance and degradation.
-
Product
5G 256-Element Active Antenna Innovator’s Kit
AWA-0134
-
The AWA-0134 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0108 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0108, the antenna provides +60dBmi (1000 W) of EIRP. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWA-0134 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.
-
Product
Interchangeable Probe Active Transmitters
HD2817T…Series
-
The instruments of the HD2817T… series are transmitters, indicators, and ON/OFF regulators with data logging functions, they measure temperature and humidity. The instrument has a large, backlighted, graphical display.
-
Product
InfiniiMode Active Differential Probe, 1.5 GHz
N2750A
Oscilloscope Probe
The N2750A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2750A probe’s InfiniiMode provides the following modes of operation.
-
Product
1.5 GHz, 1.0 pF Active Differential probe
ZD1500
Differential Probe
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
Product
Filtered Analog Input Expansion Board
MSXB 048
-
The MSXB 048 Filtered Analog Input Expansion Board has a four-pole low-pass Butterworth filter on each of its 16 single-ended channels. For DAP applications that require analog filters to take out all above-Nyquist frequencies before signal conversion, it simply replaces the MSXB 037 Analog Input Expansion board. Signal inputs normally connect to the MSXB 048 through a panel-mount DB-37 connector.
-
Product
Individual Optical Filters
-
Our comprehensive line of Semrock optical filters helps your design attain the best signal-to-noise ratios. Steep spectral edges maximize useable bandwidth, and high transmission or reflection captures the brightest images with best-in-class Flatness. Deep and extended blocking are optimized for your application, minimizing background and crosstalk while reducing cost. Select from the extensive catalog or go with a custom filter to your exact specifications, and remain confident of uncompromising quality, reliability, and reproducible results.
-
Product
1U Louvered Plastic Grille with Filter
GP-119
-
1U high louvered plastic grille with filter is made of polycarbonate resin.
-
Product
Activity Detection Unit
DG009-M1
-
Many advanced EW receivers, particularly those associated with ECM jamming systems, do not require the high resolution frequency information associated with a DFD or IFM based receiver. This is typically the case where a single pulse present within a broad frequency band is required to be detected and instantaneously down-converted to an IF band.TDS manufactures a range of Frequency Activity Detectors (FADs) also known as Activity Detection Units (ADU) which perform frequency measurement of an RF pulse and output data in as little as 15ns. The basis of these products is TDS’s ability to produce high performance broadband channelisers and integrated detectors. These devices are ideal for receivers which must operate in very high pulse density environments.
-
Product
"Standard" RF Low Pass Filters
-
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
Product
Flashlamp Pumped Actively Q-switched Lasers
NL300 Series
-
NL300 series electro-optically Q-switched nanosecond Nd:YAG lasers provide up to 800 mJ per pulse at 1064 nm. A wide range of harmonic generator modules for generation up to a 5th harmonic (213 nm) is available. The NL300 series nanosecond lasers are an excellent choice for many applications, including laser ablation and marking, OPO pumping and other critical tasks.
-
Product
Harmonic Filter Resistors
-
Post Glover designs, builds and tests their harmonic filter resistors in accordance with applicable IEC and IEEE standards to guarantee their performance. With no two installations ever being the same, our experienced engineers develop the proper solution for your particular application and environment. Our low inductance designs are built using all stainless steel elements in corrosion resistant enclosures chosen for your unique specification. Request a quote for your custom harmonic filter resistor.
-
Product
Nemo Active Probe
NTP10010A
-
Keysight’s Nemo Active Probe is an ideal solution for performing automated, unattended large-scale measurements in key locations where people are using their smartphones and where it is critical to ensure excellent network service. Nemo Active Probes can be deployed discreetly in hotspots, vehicles, and fixed locations, such as airports, offices, campuses, and shopping malls as well as in moving vehicles, such as trains, taxis, delivery trucks, and ships.
-
Product
Mid-Range Gas Filter Correlation CO2 Analyzer
Model N360M
-
Teledyne Advanced Pollution Instrumentation
The Model N360M measures carbon dioxide (CO2) by comparing infrared energy absorbed by a sample to that absorbed by a reference according to the Beer-Lambert law.The N360M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO2 known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO2 in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure. A nitrogen purge system is provided for the GFC wheel assembly to eliminate the effects of ambient CO2, if necessary.
-
Product
Precision AC/DC Active Current Shunt
2575A
-
A versatile, powerful calibration tool, the 2575A Precision AC-DC Active Current Shunt measures both AC/DC current and works as a standard for low-level resistance calibration requirements.
