Test Switches
-
product
In-Circuit Testing and Test Engineering
5184 Test NodesHPUX or Windows60 Mhz ASRU Frequency Counter, Timer10 Mhz Clock, 6 Mhz data ratesVector Test for VLSI, PLCC & ASICSTestjet and VTEP Vectorless TestingAdvanced Boundary ScanSilicon Nails AvailableSeries V upgradeable
-
product
Electrodynamic 2-Axis Switching, Simultaneous Vibration Tester
It is an electrodynamic 2-axis switching, 2-axis simultaneous vibration tester with a test frequency band up to 2000 Hz.
-
product
Pressure Testing
All metal, plastic, and composite parts intended to contain liquids or gases under pressure are required to undergo stringent pressure testing procedures to meet qualification standards.
-
product
Test Module
FailSim
FailSim simulates a faulty component and allows the user to quickly and simply improve the actual fault detection of a test program. The result represents a definitive conclusion for tested or untested components.
-
product
Preselectors and Switch Filter Banks
Our preselectors and switch filter banks offer low noise figure, high dynamic range, state-of-the-art filter rejection with high channel-to-channel isolation front ends, realized in compact building blocks, designed in custom form factors. Applicable markets include: EW, missiles, radar, communications and space.
-
product
3U VPX 1/10 GbE Switch
ComEth4412a
Cutting-edge hybrid managed switch combines PCIe Gen3 (8GT/s) and 10/40 Gbs Ethernet. Developed in alignment with the SOSA™ standard, the ComEth 4412a data plane PCIe lanes deliver up to 512GT/s of switching capacity.
-
product
PXI Dual 44x4 Matrix, 1-Pole Switching
40-536-021
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance.
-
product
PXI 32 Channel Switch Simulation Module
40-480-221
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
product
Test Leads
PMK Mess- und Kommunikationstechnik GmbH
It is used to test and measure the current in a circuit. These are simple devices which are coated and colored to indicate positive and negative with the device connector on one end.
-
product
48-Ch SPDT 1A-100VAC 24VDC Switching
YAV91074
The YAV90074 module contents 48 SPDT Relays independent. Each relays PCB contact track is shielded individually in order to handle very low voltage signals and audio signals with extremely low crosstalk. The build-in power supply includes two extra filters to reduce the DC voltage ripple to the relay coils; the control tracks have been drawn in quadrature with signal ones, reducing the inductive coupling produced by the transient current.
-
product
Test Strips
High-quality Hach chemistry in an easy-to-use test strip. Simply dip the strip into the sample and compare the color to the colors on the bottle to determine the reading. The test strips are accurate, portable and inexpensive. Applications include potable water, waste water, swimming pools and spas, industrial process applications and more. Available parameters include chlorine, nitrate and nitrite, water hardness, alkalinity, chloride, ammonium and more. Hach offers a high-quality 5-in-1 test strip that measures free chlorine, total chlorine, hardness, alkalinity, and pH—all in one strip.
-
product
Dynatrol® Liquid Level Switch
CL-10RH
The Dynatrol® Type CL-10RH Liquid Level Detector and EC-102B or EC-103C Control Unit is used for high, intermediate or low point level detection of liquids and slurries. This is typically a replacement unit for existing CL-10RH units in the field. The CL-10GH is phasing out the older style liquid level detector.
-
product
Test plug
ENGMATEC produces industrial, highly wear-resistant contact plugs for in-circuit and functional tests. They have been specially developed for a very large number of test processes, as they often occur in a wide variety of industries in the production process.
-
product
Switch Device for PCI Express
The Switch Device for PCI Express provides two PCI Express upstream ports and eight downstream ports. You can connect the downstream ports to external devices, such as a Software Defined Radio Reconfigurable Device, to create large multichannel, multiple input, multiple output (MIMO) systems. You can also connect multiple Switch Devices for PCIe to a single PXI Express chassis to create large MIMO systems with a Software Defined Radio Reconfigurable Device.
-
-
product
Test Solutions
Making test solutions are still by far the largest division of our company with an activity level of around 65% of our turnover, and with long term relationship to customers like Danfoss, Bang & Olufsen, Siemens, Grundfoss, Vestas and many more, it is still today the very foundation, on which our entire company is based.Our concept is based on high level software development, that is combined with electronical and mechanical engineering, thus controlling all the processes involved to create the most suitable test solution for our customers.
-
product
IPTV Testing
EXFO offers IPTV test solutions to assess the network copper physical layer, validate the xDSL service and test the performance of the IPTV component at any stage of the deployment. Our Ethernet IPTV testing, IPTV analysis capabilities and advanced IPTV monitoring solutions offer complete end-to-end quality of experience (QoE) assessment for IP video. EXFO enables providers to successfully introduce video services faster and manage them more cost-effectively, by continually ensuring the highest service quality.
-
product
Compact Unmanaged Ethernet Switch
ML600
The MultiLink ML600 is a Compact Unmanaged Ethernet Switch that is ideal for Industrial Facilities, Substations, and Transportation environments that have few Ethernet devices in one location. As a very cost effective solution, the ML600 will supply you with high speed networking in your harsh environments and is equipped with Link Loss Learn (LLL) that allows for use in redundant architectures thus ensuring you will always have access to your devices.
-
product
SMD Array Type LCR Test Fixture
16034H
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
product
PXI High-Density General Purpose Switch Modules
Our PXI high-density general purpose switches provide an ideal solution for applications requiring dense arrays of uncommitted relays.All reed relay modules use high-quality sputtered ruthenium relays that exhibit excellent contact performance under low and medium level switching conditions. Do you have a general purpose application that requires high power handling? We also have electro-mechanical modules that are ideal for just these situations.
-
product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass
40-860A-012
The 40/42-860A-012 is a PXI/PXIe single insert/bypass switch with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
Switch Matrices
Mercury System’s family of rugged, custom-designed switch matrices are available in rigid PCB construction, module-based packages, or rack-mount solutions. Each switch matrix is a highly integrated, SWaP-optimized assembly consisting of an assortment of switches, filters, amplifiers, attenuators, limiters, and drivers. The result is high speed channel selection, high isolation, high linearity, and low insertion loss.
-
product
UltraCMOS SP8T RF Switch
PE42582
The PE42582 is a HaRP™ technology-enhanced absorptive SP8T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42582 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
product
Test Panel
TA-5
A complete NAV/LOC/GS/MKR test panel designed around the VIR30/31/32 units. Requires channeling source. Combining the TA-6 panel provides a complete integrated system.
-
product
Switch Matrices
Configurable, high performance, non-blocking RF switching matrix units from HF to SHF
-
product
Performance Testing
If you want to check the strength of your application or the server’s strength you will need to find out how much load, in terms of the number of users the application can handle. We use the Performance Testing techniques, to check the load an application can handle.
-
product
Vibration Testing
Response Dynamics Vibration Engineering, Inc.
We most often characterize a problem first and work from known conditions, and stay in “the known” as we proceed by making sense of what we observe as we move forward. We test and analyze the change in dynamics we are trying to create in real-time, on site, and often make changes to our experimental test plan on the fly as we discover how a system is actually behaving. In doing so we often get meaningful results from which we can make sound engineering decisions in a short time frame. We don't just make measurements and spit out data. We help identify the problem and propose solutions.
-
product
Test Compliance
AMETEK Programmable Power, Inc.
A growing number of electronic products manufactured today have to meet international regulatory requirements for emissions and immunity. This is particularly true for products sold in the European community as well as a growing list of countries in the Far East. AMETEK Programmable Power compliance testing solutions measure products for the latest standards.
-
product
Vibration Testing
Vibration testing includes kinetic energy transfer to the test specimen, often described as the Device Under Test or simply DUT. Typically specified in terms of displacement, velocity, acceleration or the corresponding power spectral density units as a function of frequency. The form of the vibration may be sinusoidal, random, or a combination.
-
product
Environmental Testing
Intertek Total Quality Assurance environmental laboratories test client samples around the world for trace chemical compounds and pollutants. Environmental chemists operate state-of-the-art analytical instrumentation, testing to government, regulatory, and industry standards. Analytical capabilities include trace and ultra-trace analysis for hydrocarbons, petrochemicals, metals, contaminants, and other materials.
