Voltage Preamplifiers
-
Product
Carry Case For Voltage / Continuity Testers
CP1190
-
Complete with belt loopSize: 290 x 75 x 45mm.
-
Product
5-50V AC/DC Voltage Tester
1930A
-
Peaceful Thriving Enterprise Co Ltd
*Reinforced casing.*With cETL Approval.*Check voltage on 5-50V AC/DC.*Insulated housing and test leads.*Pocket clip for added convenience.*Built-in LED indicator will glow when voltage is present.
-
Product
High Voltage Power Supplies
-
High voltage SCR controlled power supplies require the following:Output voltage is high. Output current is generally Low.Voltmeter and ammeter display the output voltage and current under load.Potentiometers are used to adjust output voltage and limit output current from minimum to maximum.
-
Product
Non Contact Voltage Indicator
PL107N
-
Contact-free audible and visual indication of AC voltages between 90 and 1000 V AC Clear, omnidirectional flashing LED Quick and accurate detection of cable breaks Detects microwave leakage Phase detection in sockets Press to test switch avoids nuisance buzzing and extends battery life Supplied complete with 1.5 V AAA batteries
-
Product
400 MHz High Voltage Passive Probe
HVP120
-
High voltage single-ended passive probes are suitable for a wide range of applications where ground-referenced high-voltage measurements must be made safely and accurately. There is also a sense pin to automatically configure the oscilloscope for use with the probe.
-
Product
LXI High Voltage Switching - 20xSPST Plugin Module
65-233-903
-
The 65-233-903 plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Bright Color Light Induction Voltage Tester
6877-58
-
Wenzhou Zhengyuan Electronic Co., Ltd.
Digital live-wire voltage reading. Non-contact voltage (NCV) detection for safety.
-
Product
Insulating Boots (Gloves) Withstand Voltage Tester
-
Weshine Electric Manufacturing Co., Ltd
80KV Insulation Boots Withstand Current Leak Testing Withstand Voltage Tester
-
Product
Cycle Voltage Drop (Rise) Simulator
STT-CSS-20P1
-
Beijing KeHuan Century EMC Technology Co,.LTD
*Using 2 The regulator, and the rated voltage adjustable automatic voltage regulator, power fluctuations avoid adversely affecting the test results. Simulate the test under 110V power supply. It can simulate the fluctuation of the power grid under extreme conditions (such as high or low power supply voltage in remote areas).
-
Product
Stand Alone Low Voltage Testers
-
Low voltage testers are a special type of device used to identify opens and shorts in applications that are driven on low voltages.
-
Product
Voltage Tester
-
*Simple and user friendly*Check 1.2V - 230V AC & 12V DC directly*Check ground line and phase line and breakpoint of the AC directly*No battery is required
-
Product
M-LVDS (Multi-Point Low Voltage Differential Signaling)
-
M-LVDS (multipoint low voltage differential signaling) is a multipoint high speed differential electrical interface with support for up to 32 nodes. Analog Devices M-LVDS products offer the industry’s highest ESD performance transceivers with high noise immunity receivers and extended common-mode range. These products are ideal for applications where designers need to transmit at data rates up to 100 Mbps or 250 Mbps to multiple nodes.
-
Product
Digital & Light Voltage Tester
130855
-
Wenzhou Zhengyuan Electronic Co., Ltd.
Digital live-wire voltage reading
-
Product
Voltage Probe
KHZ43201
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.
-
Product
USB Preamplifier, 10 MHz to 4 GHz
U7227A
Amplifier
The U7227A, 10 MHz to 4 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurements.
-
Product
Voltage Stabilizer
MS 7643
-
VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.
-
Product
PXI 10 Channel High Voltage Attenuator
41-660-001
Attenuator
The 41-660 and 41-661 are high voltage attenuators designed to reduce the high output voltages commonly generated by some types of sensors. This is in order to produce manageable signal levels that can be acquired by typical data acquisition devices in a PXI system.
-
Product
Voltage Maintenance Program
VoltRef
-
VoltRef provides the power of automation formaintaining statistical control of the volt in yourlaboratory. This program controls a low thermalscanner and voltmeter to compare voltagestandards using the process recommended by NISTand other national laboratories.
-
Product
GAOTek Portable H/L Voltage Clamp Current Leaker
GT00YA00ZX
-
The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat resistant, shock resistant, and insulating. It provides additional functionalities such as online current testing, peak and data holding, data storage, detection of high and low current in primary and secondary circuits separately, and provision of suitable calculations to conclude change in high and low pressure.
-
Product
LXI High Voltage Switching
65-233-902-HI
Switch Module
The 65-233-902-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Combined High Voltage Test Set
-
is extensively used to measure AC and DC voltage of different electrical devices.
-
Product
Electrical Testers & Voltage Continuity Testers
-
Fluke’s line of electrical testers and voltage detectors are designed for use in every application and in nearly any environment. From non-contact voltage detectors and voltage testers with continuity detectors, to open-jaw current testers and open fork testers with FieldSense® technology (for voltage and current measurements without test leads), these testers are accurate, safe and easy to use.
-
Product
Precision High Voltage Meter
-
Precision High Voltage Meter offers the highest level of measurement accuracy, yet with its color touch screen – is surprisingly easy to use. Vitrek leverages DSP technology to provide outstanding AC &DC voltage measurement accuracy, stability, repeatability and resolution. The 4700 High Voltage Meter offers performance that rivals traditional high voltage reference dividers – yet unlike the tedious divider, the 4700 provides instant, direct, high voltage measurements in a highly portable, compact and rugged bench top enclosure.
-
Product
50 Ω High Voltage Pulse Generators
-
High Power Pulse Instruments GmbH
50 Ω High Voltage Pulse Generators by HPPI GmbH
-
Product
Programmable Voltage Reference Plug-In
ProDAQ 3202
-
The ProDAQ 3202 voltage reference card is used in the ProDAQ 3180 ultra-performance motherboards and LXI function card carriers. The ProDAQ 3202 voltage reference card is plugged directly onto the motherboard or carrier and can distribute the reference voltage to all ProDAQ function cards via two signal lines. This allows the distribution as a differential signal to overcome possible noise pick-up.
-
Product
High Voltage Amplifiers
-
Advanced Energy is a trusted high voltage power supply provider with over 40+ years of experience. Our extensive line of Trek high voltage amplifiers offer numerous voltage and current ranges to accommodate your demanding applications. Protect against output short circuits and over-voltages. For protective shutdown, utilize automatic crossover compliance limits or current trip features.
-
Product
High Voltage Non-Contact Current Probe
P02-0802
-
The TESCO High Voltage Non-Contact Current Probe (Catalog No. P02-802) was developed using current sensor technology. It is a two-piece, True RMS ammeter with a fiber optic link between the high voltage sensor and the readout at ground potential. The sensor is mounted on a hotstick and slipped over a high voltage line.
-
Product
AC / DC Voltage And DC Polarity Tester
1861
-
Peaceful Thriving Enterprise Co Ltd
*With cETL Approval.*Built-in LED and neon lamp indicator.*Neon lamp for 120V-230V-400V AC.*LED Display for 12V-50V and polarity.*Long lead connects tester body and probe.
-
Product
High Voltage Pulse Attenuators
-
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
Product
Digital High Voltage Meter
-
AllWin Instrument Science and Technology Co., Ltd.
Voltage, is 4 1 / 2 digital displayTrue RMS measurement High accuracy and stableSuitable for all waveform measuremen
