Current Preamplifiers
-
Product
Closed Loop Hall AC/DC Current Sensor
CYHCS-SH
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can beused for measurement of DC and AC current, pulse currents etc. The output of thetransducer reflects the real wave of the current carrying conductor.
-
Product
Primary Current Injection Testers
-
Primary Current Injection Tester is designed for testing protective relay and circuit breakers and also testing the turns ratio of current transformers at high variable currents. A test current is injected into the primary side of a system to determine how the system behaves at particular levels of current. This test makes it possible to determine whether the relay will trip and how long the current needs to flow before the trip is initiated.
-
Product
100A, 2 MHz, DC/AC Current Probe, BNC, 100A Peak, 70A rms, 1 meter cable
T3CP100-2
-
100A, 2 MHz, DC/AC Current Probe, BNC, 100A Peak, 70A rms, 1 meter cable.
-
Product
Voltage, Current and Power Measurement
-
Educated Design & Development, Inc.
For measuring current, especially higher currents and quicker than series ammeters. These units are considered the finest available. All units are extremely rugged, reliable, and versatile.
-
Product
3KVA Leakage Current Tester
2675C3
-
Shenzhen Chuangxin Instruments Co., Ltd.
3KVA Leakage Current Tester
-
Product
Leakage Current Tester
-
Premier's Leakage Current Tester (also known as Hipot Tester) simulates the effect of a person touching exposed metal parts of a product and detects whether or not the leakage current that would flow through the person's body remains below a safe level.
-
Product
Current clamps
-
Precision ammeters determine the intensity of an electric circuit without interrupting the current flow.
-
Product
Split type Pulse Current Sensor
CTF-05T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For detecting current pulse with open collector output (for power pulse)
-
Product
Split type Pulse Current Sensor
CTF-05M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Pulse current detection for power demand meter.*Through hole type CT.*Open collector output.
-
Product
Current Probe For Multimeters
CP 1000
-
The CP 1000 current probe has been designed for use with multimeteres respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
Product
Zero Phase Current Transformer
MZL-30
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Split-core type for measuring zero phase current
-
Product
MCB Tripping Current Characteristic Test Bench
-
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
Product
Current Probe/DMM
685
-
The #685 is a great tool for all purpose electrical testing. Applications include: fuel injection systems, fuel pumps, charging systems, electric motors, and most parasitic drains. Capable of measuring as low as 10 milliamps!
-
Product
Current Caliper
KH23101
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH23101 current caliper is a toroidal transformer used to measure EMI current. When measuring, the caliper does not directly touch the electrical conductor or the cable under test. The conductor passing through the caliper window is used as the single-turn primary wire of the transformer, and the secondary is designed to be multi-turn. Use with 50 Ω receiving system (such as EMI electromagnetic interference field strength meter or spectrum analyzer). In order to facilitate installation and rapid measurement of EMI current, it is designed as a caliper that can be opened.
-
Product
Current Loop Expansion Kit
OP-SB85C
-
This expansion kit supports current loop communications.The kit incorporates a communications circuit with photo-coupler isolation and constant-current power supply of insulated type, thus realizing not only monitoring but also easy communications testing with passive or active current loop devices.
-
Product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TC
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Eddy Current Testing
-
Zetec is the industry leader for cost-effective eddy current testing in complex applications. We have the most extensive experience, and we develop the highest quality ECT inspection products. When it comes to understanding your needs, we’re your trusted advisor. And from instrumentation to probes to software, you can count on us to provide a complete inspection solution that will help you realize a cost savings in the long run. etec Eddy Current technology and products provide a fast efficient solution for near surface anomalies in conductive material
-
Product
12-Ch SPST 4A-250VAC 24VDC High Current Power Switching
YAV90PIN
-
The YAV90PIN board is designed to cover the need to control the available power supplies in a test system to the device under test. A VPC 90 series connector is used as interface with the fixture, guaranteeing more than 20.000 mating cycles. Two connector contacts per relay contact are used.
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Quad 3-Channel, 2-Pole
40-514-103
-
The 40-514-103 (PXI) and 42-514-103 (PXIe) are low density multiplexers in quad 3-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
Laser Diode Light Current Voltage (LIV) Test Instruments
-
The Yelo LIV test instrument allows LIV measurements to be taken from laser devices loaded into a Yelo module. This module can also be used with the Yelo Y1000L Low Power Burn-in system. The LIV test instrument has been designed for easy operation. Once powered on, and with laser supply enabled, the touch screen can be used to initiate, monitor and review measurements of laser devices.
-
Product
Voltage and Current Amplifier
CMS 356
-
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
Product
Precision Current Shunt
-
Has five precision selectable Ultra stable Current Shunts which ranges from 0.0001 to 1Ω. The Shunt T/C is less than 10ppm, and the internal current meter will measure from 1μA to 1000Amps.
-
Product
50 µs Pulse Medium Current Source/Measure Unit (MCSMU)
B1514A
-
The 50 s Pulse Medium Current SMU is an SMU designed for faster pulsed IV measurement. It enables a pulsed measurement down to 50 s pulse width, a 10 times or more narrow pulsed measurement than provided by a comparable conventional SMU. In addition, the instrument offers a wider range and versatility, up to 30 V / 1A, with voltage/current programmability. It is useful to characterize high to medium power devices on the new materials such as SiC and GaN, and organic devices, and the MCSMU expands your choices of pulsed IV measurement.
-
Product
8 SE Or 4 Diff. Input Channels, 4 Analog Current Output Channels, PCI Express
APCIE-3121-8-4C
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
SparkFun Current Sensor Breakout
ACS723
-
The SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
Product
BJT Voltage Preamplifier
SIM911
-
Stanford Research Systems, Inc.
The SIM910 and SIM911 are low-noise, programmable preamplifiers which are ideal for a wide range of small signal applications. The primary differences between the two models are their input impedance and input noise.
-
Product
Current Logger Sensor
NUL-202
-
This sensor can be used to measure the current in parallel or series branches of low voltage AC and DC circuits and also to investigate the dependence of the current flow through components on the voltage across them.
-
Product
30 A, 10 MHz Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 3 Meter Cable
CP030-3M
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Dc Watt Meter For DC Current Measuring
IM1401
-
Our product range includes a wide range of dc watt meter for dc current measuring.
-
Product
Preamplifiers
LNA Series
-
Low noise amplifier with 12.5 dB of gain covering the nominal frequency range 1 MHz to 3 GHz and can be used in the range from 200 kHz to 4 GHz. With its high gain and low noise figure, it will significantly increase the sensitivity of virtually all spectrum analyzers and other RF measuring instruments. All measuring instruments have a 'noise figure', which is a measure of how good the instrument is at measuring low level signals, the lower this figure, the better, although the lowest signal level will still be governed by the measurement bandwidth. A typical spectrum analyzer may have a noise figure of 20 dB or more, whereas a typical receiver may have a noise figure of 10 dB. The preamplifier has a noise figure of typically 4 dB, significantly enhancing the low level performance of such instruments, enabling signals that were previously masked by noise to be seen.
