Monitoring
-
product
Linear regulated power supply with thyristor pre-regulation
NTN
High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units
-
product
Carbon Monoxide Detector, CO
ENVIROMUX-CMD
Continuous air monitoring. Pre-set alarm points alert at: 70 ppm after 60 to 240 minutes; 150 ppm after 10 to 50 minutes; and 400 ppm after 4 to 15 minutes. Flush or surface mount. Test functionality of electrochemical CO sensing cell. Connect to RJ45 or digital input sensor ports. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1000 ft (305m). LED indicators for operation status and system test. Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL.
-
product
PANAVIA Modules
AIM’s PANAVIA test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core design with one processor for real time bus protocol support, massive memory and IRIG-B time code encoder/decoder functions are standard. AIM delivers versions of our modules with extended temperature range and conformal coating. With 8 Tx and 8 Rx channels per module, functions include autonomous transmit sequencing, continuous clock and data transmissions, host controlled double buffering, programmable interrupts, data selection on specific tag identifier, selectable triggers on data and/or tags with full protocol error injection/detection, real time bus recording and time stamping to ensure your bus integrity. Each module is delivered with a Board Support Package (BSP) comaptible to the legacy PCI and cPCI hardware modules.
-
product
Data Acquisition Equipment
Get the data you want, where, how and when you want it. Fluke gives you a broad choice in data acquisition for process monitoring and laboratory test systems. You can choose a stationary or portable data logger. Transfer data to internal memory, to a removable memory card, or to your PC. Choose a standalone or distributed networked units. And you can expand your system from 20 to 1,000+ channels, depending on the series.
-
product
Expert On Alert
Expert-on-Alert provides centralized monitoring of locomotive health status and performance in real time. Locomotives transmit data to the Wabtec monitoring and diagnostic center, where a team of experts analyzes control system status and performance data. This enables Wabtec to determine the root cause of failures while locomotives are in-transit, providing timely maintenance and repair recommendations.
-
product
Multichannel ARINC 429 Interface Device
DAS-429UNET/RTx
Our DAS-429UNET/RTx is an intelligent, multichannel ARINC 429 interface device that can be connected to any Windows device with a USB or Ethernet connector. It monitors and records all or selected 429 traffic for later analysis or reconstruction in the lab. Exalt is our Windows base graphical tool that allows you to analyze real time or recorded data using many different views: raw data, engineering units or graphical displays.Data can be then extracted from the recorded file, and re-transmitted over the bus to another system in order to see in detail what happened during the recorded test.The combination of a handheld computer, 429Unet card and Exalt provides a complete solution for testing and maintaining ARINC-429 networks.
-
product
H009 Modules
M4KH009 modules can operate as a Central Computer Complex (CCC) and/or up to sixteen Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation. The module also supports error injection and detection, and all control parameters and data may be updated in real time. Note: The M4KH009 Module is a "double size" module, and occupies two vertically adjacent sockets in the EXC-4000 carrier Board.
-
product
Electrostatic Discharge
Our electrostatic discharge (ESD) measurement and control solutions include charge plate monitors, sensors, resistivity meters, and voltmeters. Reliably monitor, measure, locate, and test for static electricity.
-
product
Cell Culture Media Analysis Platform
C2MAP System
The C2MAP™ System can be automated the process from pretreatment to measurement for culture supernatant samples and display temporal changes in the components as graphs. With the optimized LC/MS/MS simultaneous analysis method, the system can be used for the optimization of culture conditions in animal cell cultures by monitoring the consumption and depletion of media components during culturing, as well as the variation in metabolites secreted from cells.
-
product
Universal Monitoring System
R&S®UMS400
The ever-increasing frequency range of wireless communications services calls for monitoring stations up to 8 GHz, in some cases even up to 20 GHz. Typically, this requires a monitoring sensor installed close to the antenna(s) in order to keep cable losses as low as possible for highest sensitivity. This is possible for both the R&S®UMS400 and R&S®CS-MC20, thanks to an outdoor housing.
-
product
VHF True RMS Probe
The VHF True RMS Probe is a frequency compensated power probe capable of measuring power even in a multiple carrier installation. Regardless of physical waveform, the probe will measure the True RMS power of the signal. When used together with our Broadcast Power Monitor type 3024, you can add Web and SNMP capabilities to your mast site installation.
-
product
Easycheck Fiber Endface Inspector
CA3002
The integrated style design makes the size compact and operation easy. You are no longer to worry about so many cables between monitor and microscope, greatly saving the time for operation and worktable space, thus creating more productivity. Easycheck have a series different model according to different application, it has photo capture function; for transceiver checking; X、Y adjustable; image auto analysis and judgement, etc. The user can choose the desired model per the requirement.
-
product
PXI/PXIe
As a leading provider of PXI products in test & measurement market, ADLINK has devoted its extensive field experience to the PXI platform. After more than ten years and developing more than 100 PXI products for automation and testing, and as a sponsor member of the PXI System Alliance, ADLINK continues to expand PXI and PXI Express offerings with innovative products, meeting the unique needs of high-speed and high-bandwidth applications, such as spectral monitoring and signal intelligence.
-
product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
product
Audio Meter and Side Chaining Tool
Digital Peak Meter Pro
The metering capabilities of the DPMP plug-in let you control and monitor your audio signal exactly the way you want: almost every aspect of the meters can be customized. It now proposes five different scales, including Bob Katz's very popular K-System scales (K-12, K-14, K-16 and also the extra K-10). The graphs show the evolution of the audio envelopes over time, and the mid-side switch lets you verify mono compatibility problems and check the "stereoness" of your audio sources very easily.
-
product
Ultra-Low Range Gas Filter Correlation Carbon Monoxide Analyzer
Model T300U
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300U comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
Mining and Geotechnical
ESG Solutions is your best choice for subsurface diagnostic solutions for mining and geotechnical applications. Since 1993, our microseismic monitoring specialists have provided mining services in over 40 countries, with 100 projects each year on average. We work with you to understand your unique challenges and monitoring goals, then develop the right all-in-one solution for your operation.
-
product
Datalogger Support Software
Datalogger support software packages help enable datalogger programming, communication between dataloggers and PCs, and, to varying capabilities, real-time and historical data monitoring. These software packages provide support for a single station or an entire datalogger network.
-
product
Smart Protocol Analyzer
Works transparently over the Computer's I/O ports (serial & network). The analyzer supports Modbus, Fisher-ROC, BSAP, DNP and other Protocols. In addition to monitoring, this tool is capable of simulating Master and Slave devices.
-
product
PCI-Express, 16 SE/8 DIFF Analog Inputs, 8 Analog Outputs,16-bit, 8 Digital I/O, 24 V
APCIE-3021-16-3
The PCI-Express analog input/output board APCIe-3121 has 16 SE/differential inputs, 8 analog outputs, 16-bit, and 8 digital I/O, 24 V. The board is especially suited for applications in industrial process control, measurement technology and monitoring, for example for multichannel data acquisition, for the control of chemical processes, for the acquisition of sensor data, current measurement etc. in the harsh industrial environment.
-
product
Ethernet PHY
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of 10G/25G/40G/50G/100G Ethernet Physical Layer (PHY) devices offer unparalleled performance while maintaining high density at low cost. Integrated high-speed, high performance mixed signal I/O using advanced CMOS process nodes support a variety of optical and copper connectivity interfaces allowing the Ethernet PHY product line to span rack and cluster connectivity within the data center, wireless fronthaul, midhual and backhaul connectivity for 5G wireless infrastructure, and seamlessly extend to core networks over DWDM optical links. Advanced features such as in-service eye monitors, traffic monitoring, optical module identification and link training are just a few of the advantages that MACOM’s portfolio provides for end users to leverage for faster bring up, higher reliability and smarter networks.
-
product
Power Quality Analyzers
Power quality analyzers designed for monitoring all electric parameters on single and three-phase installations. An in-depth verification of electric networks operation allows optimizing and increasing the efficiency of installations and reducing consumption and costs. The innovations designed and realized by HT are exporting the made in Italy style all over the world also in this sector.
-
product
*C Series CAN Interface Module
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PXIe-2747, 2.7 GHz, Dual 8x1 PXI RF Multiplexer Switch Module
780587-47
PXIe, 2.7 GHz, Dual 8x1 PXI RF Multiplexer Switch Module—The PXIe‑2747 is a PXI RF multiplexer switch module that is ideal for switching RF signals up to 2.7 GHz in production test applications. The high channel count of the PXIe‑2747 makes it well-suited for test systems that require switching a large number of RF signals, such as switching several devices under test to a single channel on the RF analyzer. It also features onboard relay counting for relay monitoring.
-
product
- Port Miser Port Sharing Device
Model 31
FEATURES: Expands RS-232 Port by Three; Up to 19.2 KBPS; No Power. The Telebyte Model 31 Port Splitter is a passive device which attaches to a modem, printer or computer and allows up to three terminals, monitors or other input devices such as bar code readers, mag stripe units and specialized key pads to be interconnected.
-
product
Process Monitoring and Control Systems
ComoNeo and ComoScout
Consistent digitization increases product quality and cost-effectiveness in injection molding production. The ComoNeo and ComoScout process monitoring system ensure that both newcomers and experienced users can monitor and control their processes precisely and efficiently.
-
product
Control/Gateway/Display All-In-One Industrial Panel PC
PanKonix Series-HMI Panel PC
The PanKonix® series HMI is an Intel® Core™ i3/i5 and Intel Atom® x5/x7-based panel PC equipped with user-friendly, full-featured HMI software. It ensures seamless PLC connectivity through Modbus protocol support and incorporates trend charts, data logging, alarms, and cloud connectivity functions with RESTful API, MQTT, and OPCUA support for efficient data visualization and machine monitoring.
-
product
Fibretool Portable Fiber Optic Inspector - HW-700V
Shanghai Fibretool Technology Co.,Ltd.
● 2.7 inch handheld DM27 monitor;Brightness and contrast adjustment● Quick navigation, get image within 3-5 seconds; Two-way focus control● 95% Image centralization, Clear image, no interface, no flash● 27 types of adapters tips available to inspect different connectors and angle-mounted connectors with limited access space● Precise resolution (<1 um), no shadow or vignetting in screen● Reliable output signal, no default under repeated operation● Various monitors can be chosen with specific display capability
-
product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783156-02
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
product
TTL to RS232 Adapter
SKU-012-XX
The TTL to RS-232 adapter connects the Serial UART to the standard RS-232 port for testing and monitoring functionality. The Adapter facilitates ease of use and helps to reduce board space and cost.
