Marker Locators
-
Product
Marker Locator
MLD-10W/G
-
Fuji Marker locator saves you time by locating buried utilities in combination with the buried electronic marker.
-
Product
Tool, Locator, TriPaddle, Receiver
910104146
-
Tool, Locator, TriPaddle, Receiver (only for contact p/n #'s 610110128 Rev C+ and 610110177)
-
Product
Tool, Locator, TriPaddle, Receiver
910104127
-
Used with crimp tool part # 910 101 103 to crimp TriPaddle receiver contacts to 20-28 AWG wire. This locator contains an integrated wire stop for consistent contact crimping.
-
Product
Tool, Locator, TriPaddle, ITA
910104107
-
Used with Crimp Tool p/n # 910101103 to crimp TriPaddle contacts to 20-28 AWG wire.
-
Product
Tool, Locator, Thermocouple, ITA
910104135
-
Used with Crimp Tool p/n # 910101102 to crimp thermocouple ITA contacts.
-
Product
Tool, Locator, Thermocouple, Receiver
910104134
-
Used with Crimp Tool Part # 910101102 to crimp thermocouple receiver contacts.
-
-
Product
Tool, Locator, Micro Coax, Receiver
910101135
-
Included with Crimp tool kit p/n 910101132 and kit p/n 910101131.
-
Product
Tool, Locator, QuadraPaddle, ITA
910104140
-
Used with Crimp Tool p/n # 910101103 to crimp QuadraPaddle contacts to 22-28 AWG wire.
-
Product
Spectrum Marker Generator
NSG-2
-
National RF, Inc. is pleased to announce the production of a new device, the Type NSG-2 Spectrum Marker Generator. The generator is intended to be used with either spectrum analyzers or communications receivers to mark specific frequency intervals in the RF spectrum. When used with receivers, it is essentially a frequency calibrator, thus making it attractive for use with vintage receivers with analog dials. The NSG-2 provides a leveled amplitude output over nearly 100 MHz of RF spectrum, thus making it ideal to mark frequencies and signal levels on spectrum analyzers. In addition, it may be used with a spectrum analyzer, in lieu of a sweeping type generator, to align lowpass, highpass, and bandpass filters with passbands greater than 20 KHz.
-
-
Product
Fault Locator
BIDOYNG
-
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
Product
Compact CO2 Laser Marker
LP-GS Series
-
Panasonic Industrial Devices Sales Company of America
The LP-GS Series is a compact CO2 Laser Marker capable of very fine markings.Features:- Compact Head And Controller- Very Fine Marking For Small Objects- 5-Watt CO2 Laser
-
Product
Rebar Locator
Profometer PM-600
-
Profometer PM-600 is an advanced cover meter for the precise and non destructive measurement of concrete cover and rebar diameters and the detection of rebar locations using the eddy current principle with pulse induction as the measuring method.
-
Product
Pipe Locators
-
We're professional pipe locator manufacturers and producers in China, supplying the best customized service. Feel free to buy high quality pipe locator from our factory. All our portable products used in utility locations are with CE certification.
-
-
Product
Schonstedt Locators
-
Schonstedt and Radiodetection locators are designed to provide the best performance in magnetic metal and pipe and cable location in the industry. Our Metal Locator makes finding buried manhole covers and access points under soil or asphalt efficient, quick and simple.
-
Product
Pre- Locator
CFL PL3+
-
The new generation CFL PL3+ Cable Fault Pre-locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 128 km.
-
Product
Fault Locators
-
For the first time, you can detect the type of fault and locate the position of an electrical fault that causes intermittent or persistent circuit breaker trips, thus giving you the critical information needed to reduce call backs for circuit breaker trips.
-
-
Product
Fault Locator
REZAP FAULTMASTER
-
REZAP FAULTMASTER is an auto-recloser that keeps customers on supply during intermittent faults.
-
Product
BMP-3 Board Marker Probe
BMP-3
-
Current Rating (Amps): .05Voltage Rating (VDC): 15Recommended Duty Cycle: 1 sec. On (min.), 5 sec. OffTest Center (mil): 1,300Test Center (mm): 33.02Full Travel (mil): 62Full Travel (mm): 1.57Recommended Travel (mil): 50Recommended Travel (mm): 1.27Full Marker Travel (mil): 62Full Marker Travel (mm): 1.57Direction of Rotation: CCWScribed Diameter (mil): 50Scribed Diameter (mm): 1.27Rec. Mounting Hole Size (mil): 610Rec. Mounting Hole Size (mm): 15.50Recommended Drill Size: 39/64 (in) or 15.50 mm
-
-
Product
Overhead Fault Location
-
Schweitzer Engineering Laboratories, Inc.
Overhead faulted circuit indicators include easy-to-spot displays to help direct line crews to the faulted line sections—enabling faster restoration of power and improved customer uptime.
-
Product
Pipe & Cable Locators
-
Schonstedt Pipe & Cable Locators have been setting the standard for reliability and dependability in locating buried utilities – water pipes, sewer pipes, cable, electrical lines, and gas —quickly and easily.
-
Product
Visual Fault Locators
-
Optical Wavelength Laboratories
OWL fiber optic visual fault locators (VFL) are specially designed to couple a maximum of optical energy into multimode and singlemode optical fibers by using a bright red fiber optic laser. Breaks, microbends, and other anomalies in optical fibers and connectors cause the intense bright red laser light to escape, thus revealing the presence of a fault. In addition to visual fault location, OWL VFLs can be used as a visual optical fiber identifier. A visual fiber optic identifier eliminates much of the guesswork during testing by identifying the fiber under test.
-
Product
FAYb Fiber Laser Markers
LP-S Series
-
Panasonic Industrial Devices Sales Company of America
The LP-S Series Fiber Laser Marker features:- Compact IP67G-Rated Head For Harsh Environments- 17 And 42 Watt Models, Pulsed Fiber Laser- Marking Area Up To 160mm- Removable Fiber Cable For Ease Of Installation
-
-
Product
Visual Fault Locator
TM191
-
TM191 series visual fault locator is used for the measurement in single mode or multi-mode fibers. It features a rugged design, a universal connectorand an accurate measurement
-
Product
Rebar Locator
Profoscope +
-
The Profoscope+ is a fully integrated rebar locator with data storage. To increase the efficiency on the construction site this enhancement of the Profoscope not only offers real time visualization of rebars, but also automatic data collection. Writing down measuring results of testing series is a time consuming business that can be an unnecessary source of errors. The various data storage modes of the rebar locator Profoscope+ make note taking obsolete. This cordless rebar detector is ideally suited for one-handed operations, keeping the other hand free for marking rebars.
