Battery Charge Discharge
-
Product
Automatic Battery Testers
-
T100BT is an innovative, modular battery testing equipment able to combine, on a single test platform, all the tests required to detect any possible defect on battery cells and modules: from defective cell wiring, to geometrical or surface irregularities, to out-of-specs performances.The battery tester is designed for the high-volume production test of battery modules composed by prismatic, cylindrical, or pouch cells, as well in a Lab/NPI version for engineering, prototypes and low-volume battery testing. The complete configurability allows you to equip the tester with the modules and tools you need to test your products, reaching the desired throughput.
-
Product
PXI 6-Channel Battery Simulator Module
41-752-001
Simulator
The 41-752 is a 6 channel battery simulator, each channel being capable of supplying up to 7V and 300mA to the load. Each channel is fully isolated from ground and from each other allowing the channels to be connected in series to simulate batteries arranged in a stacked architecture. The 750V isolation barrier permits the 41-752 to be used to create a lower power version of a battery stack representative of those used for vehicle propulsion.
-
Product
20-50,000 Hz Charge Amplifier
203G8
Amplifier
The Trig-Tek™ 203G8 accepts pickupswith sensitivities varying from 1 to 110pC/g. It has three simultaneous outputs:Acceleration with a sensitivity of 100 mVrms/Pk g; Velocity with a sensitivity of 534mVrms/Pk/ips; and Displacement with asensitivity of 100 mV/mil DA.
-
Product
Battery Tester
G6606
-
Peaceful Thriving Enterprise Co Ltd
It can quickly test the capacity of your battery.
-
Product
EV Battery Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
5V cell equipment adopts Sinexcel innovative circuit design + high-speed DSP complex algorithm, the detection process supports multi-gear switching; The equipment integrates voltage, temperature, pressure and other auxiliary channels, 20ms high-speed working condition simulation and other practical innovative functions to meet all aspects of battery electrical performance testing.
-
Product
6/12/24/36V Conductance Battery Tester
MBT300
-
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
Product
PXI Battery Simulator Module
41-750-001
Simulator
The 41-750 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals than can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
Battery Extra Load Units
BXL Series
-
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
Product
Advanced Solar Charge Controller with 48V/96V/120V/192VV/240V/360V
SDC360V-100A
-
Zhejiang Sandi Electric Co., Ltd
The solar charge controller is the intelligent devicewith integration of controlling . It has good running performance with LCD display and convenient operation. Also have multi protection functions such as over-charge, over-discharge protection, and pole-confusion protection for storage battery. The controller is adopted PWM charging mode. It has day and night two type working mode with high reliable and safe operation, high efficiency, long service life functions.
-
Product
Automotive Battery Production Line Tester
-
The Production Line Tester (PLT) is typically installed at the end of battery production lines (finishing). An electrical load test after formation charging is essential to assure performance and quality. The energy discharged during this test must be minimized to eliminate the need for recharging after testing.
-
Product
20KV 30KV Electrostatic Discharge Generator ESD
ESD-202AX
-
Shenzhen Chuangxin Instruments Co., Ltd.
ESD simulator is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performan
-
Product
Intelligent Charging Cable: Test Strategy and Test Execution
-
The ICCB takes over the safety and control functions that are otherwise integrated in the stationary charging station. This places increased demands on the function test in production.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 1 kV Isolation
43-752A-112
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Charge Plate Monitor
-
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the charging plate (detector), which has almost the same capacitance as the device's ground capacitance , with high accuracy, and is the most suitable measuring instrument for checking the effect when installing the ionizer and for daily management.
-
Product
Scienlab Battery Test System – Module Level
SL1001A Series
Test System
The SL1001A and SL1006A Battery Test Systems – Module Level Series help you emulate sink and source for battery modules for automotive and industrial applications.
-
Product
Battery Tester
TMC-2001RTS
-
The TMC-2001RTS is our newest member of advanced battery testers. We integrated in a very small and lightweight housing all facilities for modern battery and UPS maintenance. Best price/performance ratio.
-
Product
Battery Extra Load Units
-
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
Product
Battery Chargers
-
Electronic Test & Power Systems
Our dedicated range of battery chargers support Ni-Cd, Ni-MH, Li-ion and lead acid chemistries. Industrial lead acid battery chargers with temperature compensation are available at a variety of voltage levels and output powers. The high conversion efficiencies result in a small case style making the BC-SMPS product family ideal for system integration.
-
Product
Battery Test device
ATGB 1200
-
The ATGB 1200 is a battery tester for all standard battery technologies aimed at quality assurance, production and product development. Advantages of the ATGB: Creation of customized test sequences. Generation of load curves and peaks. Temperature measurement at the battery
-
Product
Programmable USB Hub with 4 Charge Ports
-
The USBHub2x4 is a programmable USB 2.0 compatible hub featuring 4 device downstream ports with standard USB type-A receptacles and each port is capable of delivering up to 2.5A simultaneously. With two host (upstream) connections using usb mini-B connectors, the USBHub2x4 is perfect for environments where multiple devices need to be shared or switched between two host computers. E.g.: software regression testing, iPhone software development and validation, Android software development and validation, USB device regression testing, manufacturing testing, device burn-in testing and USB device charge-curve testing.
-
Product
High-Volt Storage Battery ClusterTest System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
1700VPACK test equipment adopts sinexcel advanced high frequency isolation solution, small size, high efficiency, low heat dissipation, flexible configuration, the detection process supports multi-gear switching; The equipment CAN be widely used in ESS system detection, ultra-high voltage EV PACK battery and other fields, and can also integrate a variety of communication protocols such as temperature box, water cooler, mainstream CAN CANFD 485, and support a variety of practical and innovative functions such as one-click automatic data export to meet all aspects of PACK battery electrical performance testing.
-
Product
Resistance, Ground Testing, Battery And Power Quality
-
Our testing equipment works wherever you are, whenever you need it, with precision and reliability.
-
Product
Battery Crush Test Equipment(Horizontal)
-
Guangdong Bell Experiment Equipment Co.,Ltd
Battery Crush Test Equipment(Horizontal)Application: Battery Module / Battery Pack / Battery System crush test, penetration test.Drive Mode: Electro-hydraulic ServoCrush Tool: Semi-cylinder, hemisphere (According to test standard)
-
Product
Battery Cycler
-
Rechargeable (secondary) batteries in real-world applications are charged and discharged many times until they reach end of life. Examples of this are batteries used in cell phones, PCs, power tools and automotive applications. After multiple charge/discharge cycles, cell performance starts to degrade. The batteries typically require charging more frequently until eventually they reach end of life and need to be replaced, with the original cells either being scrapped or repurposed.
-
Product
SLA battery charger
SBSC11Q
-
The SBSC11Q is a battery charger designed to simultaneously charge up to four SBSC11 sealed lead acid batteries or other SBS type batteries having a nominal voltage of 12.0V
-
Product
Counter Battery
-
This all fuels the need to redefine effective approaches in counter battery, in particular for the functions usually fulfilled by weapon location radars: target acquisition, fire control and prediction of impacts.
-
Product
High Precision Battery Internal Resistance Instrument
BT-9562
-
High-precision measurement of battery internal resistance and voltage.
-
Product
Calibrator for Battery Charger-Analyzers
VCM-100
-
The VCM 100 is an instrument designed to verify the performance and to calibrate Battery Charger-Analyzers used on Nickel-Cadmium, Lead-Acid and other types of batteries.
-
Product
Battery Testing Equipment
-
Mainly for battery testing in lab,such as 5V1mA, 5V10mA, 5V50mA,5V100mA, 5V1A,5V3A,5V6A,5V10A
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS1000
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
