-
Product
PEM Fuel Cell
48 Volt 5kW
-
It is the aim of CellCare Technologies to continually introduce new technology that can provide significant benefits over existing solutions in specific applications. Fuel cellThe latest introduction to the product portfolio is a 5kW PEM (Proton Exchange Membrane) based hydrogen fuel cell, designed to replace 48V standby batteries within remote telecoms sites, satellite base stations, ISP base stations, uplink facilities and weather data collection sites. This technology provides instant power with no hazardous waste, zero emissions, extended autonomy and a guaranteed lifetime with minimal maintenance.
-
Product
Solid Oxide and Molten Carbonate Fuel Cell Test Stations
-
Greenlight''s SOFC test systems include options for integrated reformers, de-sox, gas mixing, water saturation, pre-heating, furnace, heat recovery and water balance. These SOFC test rigs can be configured to operate on gaseous or liquid fuels, with operating temperatures up to 1000C. Pressure control is optional and furnaces can be tailored for either planar or tubular cell configurations. For single cell or button cell testing, Greenlight offers the X20 table-top SOFC test bench, including furnace and optional fixtures.
-
Product
PEM Fuel Cell Test Stations
-
Available with Greenlight''s integrated ''Intelligent Fuel Cell Diagnostics'' capabilities:FCDXTMCE certification including optional 3rd party verificationIndustry-leading software and diagnosticsAutomated reformate gas simulation (blending)5 different gas humidification technologies available, including Greenlight''s optional Rapid Response humidification system24/7 unattended operation with Emerald control and automation softwareIndustry leading cell voltage monitoring accuracyUser-adjustable safety featuresFuel cell stack leak testingOptional integrated environmental chambersOptional high temperature configuration, specifically designed for PBI membrane researchOptional DMFC configurationWorldwide service and support
-
Product
Hydrogen Fuel Cell
-
Honeywell Aerospace Technologies
Honeywell has a decades-long history of innovation in power generation for all kinds of aerospace and defense applications, which was further strengthened by the 2020 acquisition of Ballard Unmanned Systems, a global leader in fuel cell technologies for unmanned aerial vehicles (UAVs).
-
Product
Fuel Cell Hardware
-
The TP series cells are designed primarily for researchers who are providing their own MEAs, but they can be provided with MEAs as well. They can be offered as stand-alone cells, or as integrated equipment with our turn-key testing stations.
-
Product
Mini-Test Station
-
Mini-Test Station for low current fuel cell testing. The test station includes Analog mass flow controllers for Anode and Cathode gas streams, humidity bottles with preheaters and temperature controllers and a cell temperature controller. The test station is designed to use the customer's Potentiostat to load the cell. Manual backpressure is provided for pressures from 0-60 psig. The Mini-Test station is basically our Analog Mass Flow Controlled Low Flow Humidification System with all the options.
-
Product
Potentiostat Galvanostat
EnergyLab XM
-
EnergyLab XM is an application specific XM instrument designed for research of batteries, fuel cells, and supercapacitors. EnergyLab XM’s extreme sensitivity is used for advanced testing of lithium ion batteries and alkaline batteries. This includes research in half-cell configurations and next generation low impedance cells in the sub 100 μΩ range as well as popular battery types such as 2032 coin cell testing and 18650 cell testing.
-
Product
Motor Unit
-
Adamant Namiki Precision Jewel Co Ltd.
Today, so many units products such as medical equipment, automobiles, fuel cells, robots, and precision instruments. These performances are supported by the performance of motors, on the other hand, mechanical design, parts processing, and control The maximize the performance of the motor, which is an engine, are indispensable . The functions required for unit products are very diverse, including precision drive , high output, light weight, low heat generation, low vibration, and low power consumption.Actuation technologies such as optimum motors, speed reducer, non-energized locking mechanism "dyNALOX", compact clutch mechanism, torque transmission mechanism, control, and our core technology "cutting" "sharpening" "polishing" precision We combine process parts and precision assembly technology and we propose the optimum solution with a unique idea unique to our company, which is a motor manufacturer.
-
Product
Multiple Output Bidirectional PSU
LAB-MOBI
-
Electronic Test & Power Systems
The LAB-MOBI is a series of multi channel High Power Bidirectional PSUs. Each system is able to operate as either a DC Source or a DC Electronic Load. This integrated approach features high dynamics enabling the user to switch seamlessly between quadrants. When sinking energy from the unit under test the LAB-MOBI automatically inverts the DC to AC and synchronises this output to the grid. Dedicated application modes are available for battery cycling and emulation, which can be used to implement specific test routines. Other common applications the LAB-MOBI is used for include testing electric motors, fuel cells, super capacitors and solar panels. Max. Volt. Output 1000V,Min. Power 60kW, Max. Power 500kW.
-
Product
Programmable DC Electronic Load - (Economical)
63200E Series
-
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
-
Product
OHMMETERS
DOT-1000-2
-
Model DOT-1000-2, is an ac four-terminal ohmmeter to be used for the measurement of dynamic ac resistance of batteries, fuel cells and other voltage sources.
-
Product
Electrochemistry
Portable Line
-
Portable Line potentiostats/galvanostats combine electrochemical research in the laboratory with on-site research using well-established electrochemical techniques.These small and affordable portable instruments enable you to develop applications for your specific research needs. Portable Line instruments are an ideal solution in many research areas, such as (bio)sensor, corrosion, or (bio)fuel cell.
-
Product
Electronic Loads
-
AMETEK Programmable Power, Inc.
Electronic loads have found a variety of applications ranging from power converter testing to current modulation. A large range of power sources can be tested using an electronic load from converters, inverters and UPSs to electrochemical sources such as batteries and fuel cells.
-
Product
sbRIO-9225, Non-Enclosed, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780588-01
Voltage Input Module
Non-Enclosed, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The sbRIO‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three sbRIO‑9225 channels. Non-enclosed modules are designed for OEM applications.
-
Product
Electronic Loads
-
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
Product
Programmable DC Electronic Load
M97 series
-
The new M97XX series programmable DC electronic load is a new generation product designed from Maynuo Electronic Co.,Ltd. Incorporating high-performance chips, the M97XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M97XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications. From 150W to 200KW, there are many models to choose from :
-
Product
DC Electronic Loads
-
Electronic Test & Power Systems
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.
-
Product
High-Temperature Test Systems
-
HT-PEM (high-temperature polymer electrolyte membrane) technology represents a further development of PEM fuel cell technology. Unlike conventional PEM fuel cells, which operate at lower temperatures, HT-PEM fuel cells can reach temperatures of up to 200 °C.
-
Product
Electronic Load System
-
Electronic loads are required for testing fuel cells such as PEMFC, AFC, PAFC, MCFC, SOFC. These electronic loads are designed either in IGBT technology with power, current and voltage ranges according to specific requirements or in transistor technology. Electronic loads in IGBT technology are designed for high voltage ranges up to 900 V, current ranges up to 1000 A, and power ranges up to 480 kW.
-
Product
Programmable DC Electronic Load
DL3000
-
The DL3000 series is a cost-effective, economical programmable DC electronic load with a friendly human-machine interface and excellent performance specifications. It provides a variety of remote communication interfaces to meet diverse testing needs for design and testing. A wide range of solutions are available for a wide range of industries including automotive electronics and fuel cells.
-
Product
Fuel Cell Test Systems
-
Fuel Cell Test System is a complete test station for operation and measurement of PEM/DMFC fuel cells.
-
Product
FC Impedance Meters
-
designed for testing of the fuel cell with the small current (5 A or less), and not only the current-voltage characteristic test, the KFM2005 can easily measure for the impedance of a fuel cell using the AC impedance method, and the Cole-Cole plot. Using the measurement data of the Cole-cole plot, it is possible to calculate the circuit constant of the approximate equivalent circuit of the fuel cell. The built-in DC load (60W) is capable to operate from 0 V, and it can perform the test for the fuel cell up to 20V and 5A.
-
Product
Fuel Cell Test Stations
-
The Fuel Cell Test Stations provides control of flow, temperature and pressure for the anode and cathode gases. The station incorporates a DC electronic load. The Station also includes two humidity bottles, an Operating Manual and a computer utilizing LabView-based software.
-
Product
DC Electronic Load
-
DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more.
-
Product
Electronic Load
-
* Fully programmable, self-contained, air-cooled solid state load.* Patented design is optimized to provide ultra-low impedance operation for fuel cell testing.* Load is compatible with AC impedance or frequency response analyzers.* Interchangeable shunts for precise operation over a wide dynamic range.* Ten built-in cell voltage monitoring inputs optional. Additional voltage monitoring inputs available.* Ethernet Interface for simple configuration and expansion!* Combine with additional Fideris™ Innovator Series™ modules to create a fully-integrated,fully-automated, customized test system.* System-wide control of all Fideris™ Test System Components using FCPower™ Software,LabviewTM, or other programming language.* Integrated hardwired Run/Standby signal.
-
Product
Test Cell System
qCf FC50/125
-
qCf: Our revolutionary test cell system for the professional characterization of fuel cells.
-
Product
Testing And Simulation
-
Uni- and bidirectional power supplies for testing and simulating batteries, fuel cells, electric drive trains and other components.
-
Product
Liquid Cooling High Amp
qCf 12 High Amp
-
qCf Liquid Cooling High Amp: Our system for the professional characterization of fuel cells for high current densities and direct flow field cooling.
-
Product
Trace Oxygen Analyzers
-
Alpha Omega Instruments trace oxygen analyzers and transmitters incorporate an advanced electrochemical sensor that provides exceptional life, accuracy, and stability. Alpha Omega Instruments electrochemical sensors provide as much as three times the life of conventional “fuel cell” type sensors. And, if you are looking to measure from parts per billion to 100%, Alpha Omega Instruments offers a high-performance zirconium oxide oxygen sensor.
-
Product
Hygrometer
UHQ-4P
-
Buck Research Instruments, LLC
The UHQ-4P is a chilled mirror hygrometer that is designed for measuring elevated dew points, such as those found in fuel cell and combustion applications Using technology developed for the CR-1A, CR-2 and CR-3, this instrument is unique because it does not use TE coolers to cool the mirror and thus is extremely fast and can handle very high temperatures. The UHQ-4P can measure dew point up to 150°C at pressures up to 150 psia (10 bar). It can display %RH with an optional ambient temperature sensor. The UHQ-4P is designed to measure in hydrogen, air and most non-corrosive gases at pressures ranging from near vacuum to up to 150 psia (10 bar).
