- TEAM SOLUTIONS, INC.
product
Current Loop 20 MA Constant Current SI-module With Optical Isolation
MXTTY
Current loop 20 mA constant current (active, passive) SI-module with optical isolation.
-
product
RCD Loop Line
Digital measuring instrument for RCD testing with Loop and Line resistance measurement also without tripping the RCD.
-
product
Carrier Convergence Processors
Macom Technology Solutions Holdings Inc.
Macom offers a line of infrastructure voice processors, in concert with the carrier-grade Media Stream Processing software, that delivers a complete, integrated VoIP media, data and fax, signaling and control processing solution. Combined with powerful DSP cores with flexible packet processing engine and a rich set of interfaces, the processors support 256 to 640 channels of packet-TDM and packet-packet operation across the entire range of IP modulations, for VoIP and VoATM applications. A large...show more -
product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asy...show more -
product
PCI-7811, 1M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779363-01
The PCI‑7811 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7811 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
product
PXIe-7822, PXI Express Digital RIO with Kintex-7 325T FPGA
783486-01
Kintex 7 325T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each ...show more -
product
Digital Electrical Network Analyzer
1826 NA
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Earth Resistance without the need for poles in the ground or external measuring wires.● Earth measurement uses the real earth current path and the current generated by the electric network, without the need for any disconnection.● The Earth Resistance displayed is exactly the earth resistance that the earth current will need to go through if an earth fault occurs. No need to add all the bonding points and connection paths resistances.● Dis...show more -
product
Automatic Hysteresis Graph Test System
DX-4DMT
X-4DMT automatic hysteresigraph system accords with the standard permanent magnet test system, GB3217-92, used to measure the major and minor hysteresis loops, demagnetization curves, recoil hysteresis loops and initial magnetization curves in different temperature of ferrite, AlNiCo, SmCo, NdFeB and quenched material, and gives the magnetic parameter, Br, Hcb, Hcj, (BH)max, Hk and so on, and could meet different requirements on test function, precision, power capability, reliability, efficiency, price, local environment from laboratory to enterprise's production line.
-
product
Data Logging
The LogTxt macro can be used together with a timer macro in a loop to produce a data log that consists of a timed series of data samples. Each line in the file can be anything you want, typically a time-stamp (including date, if desired) plus one or more values recorded at that time. The interval between samples can typically be from less than a tenth of a second, up to hours or days... or even longer.
-
product
CNC Vision Measuring Machines
SVM DCC Standard / Classic Series
*Professional and international origin brand name*Designed by professional development team, with style and structure in line with engineering engineering principles*Three axis CNC control system (fully closed loop servo control system) ensures the accurate positioning.*Modular design enables easy & convenient installation and maintenance.
-
product
32-CH 12-Bit 100 kS/s Isolated Analog Input Card
PCI-9113A
ADLINK PCI-9113A is a 32-CH, 12-bit, 100 kS/s isolated analog input card. The PCI-9113A provides analog inputs with 3 programmable input ranges for both bipolar and unipolar inputs. The 32-CH single-ended analog inputs can be converted to 16-CH differential analog inputs, which improve the noise rejection in harsh industrial environments. The analog inputs are isolated from the PC's system ground. This feature not only protects the PC from being damaged from surges on the signal lines, but also ...show more -
product
Loop and Line Powered Level Switch
Safety IntelliPoint
The Safety IntelliPoint level switch provides a capacitance probe level switch with either a current output or relay contacts and “On-Board” self-diagnostics to ensure reliability. This SIL Intellipoint conforms to SIL 2 specifications providing the ultimate in level switch integrity and level sensing elements for a wide variety of temperatures, pressures, and materials.
-
product
Telephone & Exchange Tester
ETT 10
Maintenance statistics of telephone networkshave shown that for most of the failures, theexchange - line - subscriber (EXCH-LINE-TEL) sections are responsible. Accordingly, the first step of the troubleshooting procedure is to locate the breakdown spot, i.e. to find out whether thefailure source is within the exchange, the subscriber site or in the line (local loop). Thisproblem can be easily solved by theTelephone & Exchange Tester ETT 10, in most cases without requiring the technician to visit the subscriber or the junction boxes along the line.
-
product
Compression Unit
BK1611
The BaKo BK1611 is a Compression Unit that uses a real time feedback loop to create a frequency sweep with constant level output. This would normally be used for either research or for calibration rather than product line testing and is useful because of its extreme stability. The BK1611 is not a dedicated system so it can be integrated into a variety of systems to be used for microphones, speakers or vibration motors.
-
product
Alarms
Devar alarms are designed to accurately monitor process trip-points from current, millivolt, DC volts and thermocouple signals. These alarm points can be easily set in percent of signal or directly in engineering units. The units will constantly monitor the set point against the actual signal and switch a 10 amp SPDT relay when the set point is exceeded. Alarms are available in wall mount, panel mount, track or DIN rail mount, AC/DC line voltage powered or loop powered versions.
-
product
PCI-7813, 3M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779370-01
The PCI‑7813 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7813 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
product
Loop Resistance Measuring Device According to DIN EN 61557-3 (VDE 0413-3)
PeakTech Prüf- und Messtechnik GmbH
A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
product
Galaxy Craft Test Set
A low cost, high quality test set. Galaxy is made of industrial grade plastic. It is designed for rugged use and can withstand rough handling and shocks in field use. The dumbbell shape is slung on the shoulder to keep the hands free, It has an extra large belt hook equipped with a spring-loaded clip for secure holding to belt loops. The line cord is braided in superior yarn with angled bed of nails and piercing pin.
-
product
PXIe-7821, Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module
783485-01
Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each ...show more -
product
PCIe-7822, Kintex 7 325T FPGA, Digital Reconfigurable I/O Device
785360-01
The PCIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PCIe‑7822 is well-suited for a...show more -
product
ACDC
ES Series
The ES Series of line operated power supplies features near constant efficiency over theentire rated input voltage range. These electrically identical families employ a highly efficient, closed loop ripple regulation circuit, which contains a low pass filter. Each stage, transformer, filter and regulator is engineered for maximum efficiency.
-
product
Event Detectors
105/106 Series
The 105/106 Series Event Detectors are the most versatile Event Detectors in the product line. These Event Detectors monitor the electrical resistance of up to 128 simple continuity loops, each comprised of single or multiple specimens under test. Each test specimen is continuously monitored while a selectable DC sense current is passed through each channel test-loop; resistance changes exceeding the selected threshold are recorded as an event. Minimum Event Duration, Channel Current, and Thresh...show more -
product
Counter/Timer Board
MSXB 036
The MSXB 036 Counter/Timer Board is used for frequency counting, rotational speed (tachometer) measurement, and closed loop process control based on frequency criteria. Engine performance monitoring is a typical application. The Counter/Timer Board provides 16 digital input lines and 16 digital output lines, counts up to 6 MHz on 10 channels, and has two 100 MHz frequency prescalers.
-
product
Loop A Line
TX916
The Loop a Line has been a Telstra standard for 20 years. It is probably the simplest time saving device available for contractors and technicians. Once fitted to the far end of a line you can switch between Open, Short, Connect, 600 ohm, and Tone modes allowing all installation and fault location to be performed from the one end without having to go back and forward from one end of the line to the other.
-
product
Telephone Line Simulator
TLS-5
The TLS-5 Telephone Line Simulator offers the most convenient way to demonstrate or test telecom equipment where central office lines are not easily available. The TLS-5 functions as a virtual CO switch, providing four simulated central office lines with two talk paths, plus an audio interface port. Features include: 4 loop start lines, 2 talk paths, PBX features, programmable parameters, precise call progress tones, caller ID features, CLASS features, and programmable dial tones.
-
product
PXIe-7820, Kintex 7 160T FPGA, 128 DIO, PXI Digital Reconfigurable I/O Module
783484-01
Kintex 7 160T FPGA, 128 DIO, PXI Digital Reconfigurable I/O Module—The PXIe‑7820 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers s...show more -
product
PCIe-7821, Kintex 7 FPGA, Digital Reconfigurable I/O Device
785359-01
The PCIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PCIe‑7821 is well-suited for a...show more -
product
Multifunctional testers
MI 3152 EurotestXC
MI 3152 EurotestXC is an instrument from the new generation of Metrel’s multifunctional measuring instruments. The already well known functions like complete installation safety testing according to IEC/EN 61557 and AUTO SEQUENCE testing of TN, TT and IT earthing systems are managed by a completely new user interface based on large colour touch screen display. A wide range of functions is included: from on-line voltage monitoring, phase sequence testing, varistor testing, earth resistance measurement, illuminance measurement and TRMS current measurement up to RCD tests, line and loop impedance tests, specific earth resistance measurements as well as ISFL measurements and the IMD tests.
-
product
Automotive Conveyor Control
Convey-O-Track
Computer Conversions Corporation
Computer Conversions' Convey-o-Trak Series are standalone precision Conveyor Drive Positioners, designed specifically for assembly-line applications. They serve as a reliable means of precisely positioning conveyors in a truly closed loop system that can be either: exactly job/product rate synchronized position (Line Setters), or, absolute position synchronized to any adjacent conveyor (Synchronizers).
-
product
Handsfree Telephone Communication Tester
TestPhone 850
The TestPhone 850 provides both handset and handsfree telephone communication. The product provides a standard Public Switched Telephone Networks (PSTN) interface, user interface and handset and/or handsfree vocal interface to allow the user to originate or answer standard PSTN calls on both Dual-tone Multi-frequency (DTMF - tone dialling) and Loop Disconnect (LD - pulse dialling) lines. In addition the product features on-hook audio line monitoring, PSTN line polarity indication, automatic on-hook/power-off and integral ADSL digital line filtering.
-
product
200 Ampere Micro OHM Meters
HL-200
Measuring the line loop contact resistance by bridges is not the ideal method as the test current is only a few milli amperes. Thus the value is not the true value of the contact resistance. Model HL- 200 is a direct reading tester, and uses a test current of 200A DC, resulting in true value and accurate measurements. Model HL- 200 adopts digital circuit technique and is used for measuring contact resistance of switch control equipment at test current of 200A DC. The measurements are accurate as the test is highly stable. HL- 200 is a new, fully automatic micro controlled tester that measures contact resistance at 200A DC with built in printer.
