Signal Proccessing
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
product
Quadrature Signal Generator
TE5100-PCI
The TE5100 is a 100MHz Direct Digital Synthesized Signal Generator available in a 3U, CompactPCI or straight PCI format. The TE5100 generates Sine and ACMOS/TTL output signals simultaneously up to 100MHz in 1 µHz steps. Sweep, FSK, Chirp and Single Tone are generated on board. The virtual panel allows control up to 100MHz of all parameters. The TE5100 is equipped with a ±1ppm on-board TCXO clock and can accept an external clock source.
-
product
Signal Generators
Analog Devices signal generators provide an ideal solution for applications such as wireless HDMI®, microwave and millimeterwave radio, and sensor equipment. These products offer a clean signal, broad frequency coverage, and high output power for multiple applications, with competitive functionality and performance against other signal generators in their class. Our technology operates up to the 70 GHz range, and includes bench top and portable options for greater flexibility in design and development.
-
product
Baseband Signal Generator
Find the right T&M solutions for applications requiring baseband signal generation. Our product portfolio includes the well-established baseband generator, supporting many wireless standards such as WCDMA, LTE, HSPA and WLAN802.11a/b/g/n/ac, using WinIQSIM2™. Our solutions selection also includes function generators.
-
product
Compact DMX Signal And Cable Diagnostic Tool
PROTESTER
Checks DMX512 signal and 5-pin data cables. Nine diagnostic indicator LEDs. Bright, white LED flashlight built in. Leather carrying pouch included. Small, lightweight, brushed aluminum finish.
-
-
product
LVDT Signal Conditioner
NTC-6000
Quick and easy setup with front panel push buttons and LED indicatorsSelectable excitation frequency, analog outputs and bandwidthAutomatic excitation synchronization for multiple unit systemsSelf-diagnostics for LVDT failure, disconnect, or short circuitDigital communications via RS-485 2-wire multi-drop busHot swapability — setup can be saved and reloaded via RS-485 portCybersecurity lockout and tamper detectWorks with nearly any AC LVDT, RVDT, or LVRT half bridge
-
product
1.8-148 MHz Stand Alone Weatherproof Unit for the Application of DC Control Signals up to 400ma on your Coax Cable
Bias-T PLUS
The Array Solutions Bias-T PLUS is a 1.8-148 MHz stand alone weatherproof unit that permits the application of DC control signals of up to 400ma on your coax cable. By inserting the control voltage on the coax cable feed-line, you eliminate the requirement for external DC wires for powering remote devices.The Bias-T PLUS weatherproof assembly means that it can be placed indoors or outdoors for maximum flexibility. Typically, one Bias-T PLUS will be placed indoors for inserting DC on your coax feed-line, and one Bias-T PLUS will be placed at the remote device where the DC voltage is extracted.
-
product
Isolated Process Control Signal Conditioning Products
SCIM7B
SCIM7B Isolated Process Control Signal Conditioning Modules provide a complete selection of backpanels DIN rail mounting accessories, interface cables and rack mounting hardware.Each SCIM7B module provides a single of isolated analog input or output. Various input modules accept analog voltage or current signals from all types of field sensors and sources, filter, isolateamplify, linearize and convert these input signals to high-level analog outputs suitable for use in a process control system. Output modules accept high-level analog voltage signals from a process control system, then buffer, isolate, filter, convert and amplify before providing a current or voltage output to a fielddevice.
-
product
Adjustable Signal Samplers
7999
Now, you can extract a low signal level from a 50-Ohm coaxial system with the Model 7998 and 7999 series of Adjustable Signal Samplers from Coaxial Dynamics. These Signal Samplers are essential tools for spectrum analysis, RF signal scope observation, or frequency counting control.
-
product
8-CH 24-Bit High-Resolution Dynamic Signal Acquisition Module
PCIe-9529
The ADLINK PCIe/PXIe-9529 is a high-performance, high density, 8-CH analog input dynamic signal acquisition module. The PCIe/PXIe-9529 features eight 24-bit simultaneously sampling analog input channels. The 24-bit sigma-delta ADC provides a sampling rate of 192 kS/s at high resolution, making it ideal for higher dynamic range signal measurement. All channels are sampled simultaneously and accept input range up to ±10V, and the analog inputs support software-selectable AC or DC coupling and 4 mA bias current for integrated electronic piezoelectric (IEPE) sensors. The module is especially designed to meet the requirements of vibration analysis and audio testing.
-
product
PXI Breadboard Module, 2-Slot, 50-Pin D-Type
40-220A-502
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
Signal Module, Receiver, QuadraPaddle, 192 Position, Right Angle Contacts For Custom PCB Mounting (510 150 130 And 510 109 315)
510150152
This kit has everything you need to attach a VPC Receiver Module to a custom designed PCB. This includes the right angle header (P/N 510 109 315) and the Receiver Module (P/N 510 150 130).
-
product
64 Channel Dual IF Signal Processor
DP-VME-5247
DP-VME-5247 is a VME64x Dual IF Signal Processor . This dual channel up converter and down converter on-board real time data processing and analog output. This board is particularly suited for radar systems where the signals must be sampled at high rates and very high purity programmable signal generation. Application range encompasses IF signal processing, radar systems, communication systems, and IF data logging systems.
-
product
Mixed Signal Oscilloscope, 500 MHz, 4 Analog Plus 16 Digital Channels
MSOX3054A
500 MHz4 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
product
Signal Analysis
Cross-Spectrum FFT Analysis
The program Cross narrow-band spectrum is used for evaluation of the interrelation between the signals’ parameters obtained from the two primary transducers installed at various parts of the controlled object. This program can be used for detection of noise source location, for sound absorption level evaluation and the researched object acoustic properties control, for evaluation of space-time distribution of the directional energy flux (Poynting vector), for the ground cross-section FR characteristic evaluation (Nakamura method), etc.
-
product
Precision Signal Source/Function Generator
A portable, dual-channel voltage, frequency and charge signal generator with accuracies exceeding most high-cost laboratory function generators.
-
product
GPS Signal Splitter 16 Way, N Type Jack, 1 - 2 GHz, 50 Ohm Coaxial
GPS160
INSTOCK Wireless Components, Inc
Wideband Frequency (1000-2000 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA Max on DC Block PortsTri Alloy Type N Female (Jack) Low PIM
-
product
DIGITAL TV SIGNAL ANALYZER
1702/1703
The optimal signal analyzers to test and measure both analog/digital signals. Especially, these models give users the capacity to measure 'C/N' very easily and correctly, which are very important measurement factors for the TV broadcasting signal.
-
product
31-Channel Thermocouple Input Signal Conditioner
U2802A
The Keysight U2802A 31-Channel Thermocouple Input module is a thermocouple input signal conditioner device that functions to convert low input voltage signal from a thermocouple into an output voltage range suitable for the data acquisition device. The U2802A thermocouple signal conditioner is to be used together with the U2355A and U2356A model data acquisition to enable thermocouple inputs.
-
product
Signal Light for Hipot Testers
LX-signal light-HV1
2-color indicator light, red, green.With the help of the signal light tower, you can visualize potentially high voltage.
-
product
Real-Time Online Monitoring to Detect and Analyze Potential Partial Discharge (PD) Signals and Insulation Faults using UHF, AE, and HFCT
PDMonitor
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
product
Signal, Module, Receiver, TriPaddle, 64 Position, w/ Right Angle Contacts
510104109
Primary mating module 510108101. (May mate with other ITA modules, as well.)
-
product
Signal Conditioner As Circuit Board Module
INELTA Sensorsysteme GmbH & Co. KG
For LVDT Displacement Sensors, DMS Force Sensors
-
product
Converter Signal Amplifier – 4…20 mA – DIN Rail
HD978TR3
Configurable converter signal amplifier with 4…20 mA (20…4mA). Input range -10 …+60mVdc.
-
product
2 Way GPS / GNSS Signal Splitter IP67 Outdoor, N Type, 1-2 GHz, 50 Ohm, Passive
GPS201
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portTri Alloy N Type Female (Jack) 50 Ohm
-
product
Signal Conditioning Carrier
ProDAQ 5720
The ProDAQ 5720 Signal Conditioning Unit provides power and cooling for up to two Signal Conditioning Cards from the ProDAQ 58xx Series. These Signal Conditioning Cards provide conditioning for 8 or 16 channels and can be used directly with Bustec’s high-performance ProDAQ ADC function cards such as the ProDAQ 3416 16-ch. Sigma-Delta ADC Function Card or the ProDAQ 3424 8-ch. Sigma-Delta ADC Function Card.To connect the function cards to the signal conditioning cards SCSI-style cables from the ProDAQ 8010-Bx Series are used. They provide shielded twisted pair connections for signals and control.
-
product
Data Acquisition & Signal Conditioners
Electro Standards Laboratories
Electro Standards Laboratories offers instrumentation and signal processors in both encased form factors or board-only versions suitable for embedded sensor applications. Features ability to collocate with sensor and provide immediate digitization and signal processing in order to minimize ambient interference on sensitive sensors and to seamlessly integrate into networked sensor architectures.
-
product
4 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 4 Ports
GPS402
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
product
Signal , Module, Receiver, QuadraPaddle, iCon Series, 160 Position, for crimp contacts
510160101
Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
product
Cable Assembly, Twisted Pair, Differential Signals, 78-Pin D-Type Male To Female, 0.5m
A078DMR-078DFR-9A050
The A078DMR-078DFR-9A050 is a 78-Pin Male to Female D-Type Cable Assembly with twisted signal pairs suitable for differentialsignals and is designed to be used with Pickering's 40-200 fault insertion switch.
