Positioning
Aligning test set with target geography.
-
Product
3D Measuring Systems
-
Measurement systems for mobile, laptops, tablets and other specific electronic equipment, can be achieved using hi-tech materials, such as Rohacell (as used in Aerospace Industry). innco systems 2D and 3D positioning systems are custom designed to meet each new challenge, for mobile phones to wireless network equipment.
-
Product
6 Position Plug Socket Switch Life Tester
CZKS-6
-
It is designed according to terms and conditions of IEC60884-1, IEC60669-1, GB2099.1-2008 and GB16915.1-2003, for life test of plug and socket and switch products of household and similar use appliances. The device can connect with matched load cabinet, in order to conduct a test of electrical life, normal operation and breaking capacity. The equipment provide some clamp, it can test plug and socket production, wall switch, rocker switch, dial plate switch and button switch.
-
Product
Signal, Module, Receiver, TriPaddle, 90 Series, 96 Position
510104136
Receiver Module
Primary mating module 510108126. (May mate with other ITA modules, as well.)
-
Product
Levitator
-
The ultrasonic levitator is ideally suited for a large number of material science experiments in which small samples or sample quantities have to be positioned precisely. Measurements can be conducted – as they are performed in a touchless manner – without interference from a contact surface.
-
Product
Signal/ Micro Power/Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Positions, for crimp contacts
510160107
Receiver Module
Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
Product
0.25° Accuracy Full Attitude Dynamic Motion Sensor
DMS-25
-
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.
-
Product
Ionization bars
-
Wolfgang Warmbier GmbH & Co. KG
Suitable for down-stream applications ie "laminar airflow boxes"Air assistance for various applicationsComplies with IEC 61340-5-1 Ed. 1.0 (2007-08)Pulsed AC high voltage IonizationEach tip emits positive and negative ionsSelf-balancing ± 30VControl input and alarm output connectorPower supply 230V / AC via controllerOne controller is suitable for two ion barsAdjustments on controller sideEasy emitter replacement
-
Product
Surge Voltage Generator
SSG 2100
-
Cable fault location with the BAUR SSG 2100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
Product
Turns Ratio Testers
TRT Standard Series
-
When it comes to choosing a transformer turns ratio tester, TRT Standard series offers some of the most advanced instruments with LCD display out in the market. Each model measures transformer excitation current and phase shift performs automatic vector group detection and magnetic balance on three-phase transformers and three-phase autotransformers. Furthermore, they have a built-in true three-phase power source. Because of that, TRT Standard instruments can test transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.The instruments can output test voltages from 1 V AC to 250 V AC, depending on the chosen model. High test voltage of 250 V AC provides more accurate turns ratio testing compared to other turns ratio testers on the market and extremely low test voltage of 1 V AC enables turns ratio verification of current transformers.TRT Standard series consists of:TRT03 Models (TRT03A, TRT03B, TRT03C) – single-phase voltage up to 100 VTRT3x Models (TRT30A, TRT30B, TRT30C, TRT33A, TRT33B, TRT33C) – single and true three-phase voltage up to 100 VTRT63 Models (TRT63A, TRT63B, TRT63C) – single and true three-phase voltage up to 250 VMore about models differences can be found under the downloads tab, in brochures and comparison sheets.A user can create test templates using the DV Win software and store them in the PC’s memory for later use when in the field.TRT Standard series models have a built-in tap changer control unit. Consequently, it enables remote control of an on-load tap changer (OLTC) directly from the tester. In order to make the most out of this feature, the DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions and saving results. This option, especially in combination with test templates, significantly facilitates and shortens the turns ratio testing time.
-
Product
Field Ops Remote Tracker
-
10 meter positional accuracy for every kilometer traveled – without the use of GPS or RF beacons.
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 6 or 10 Positions Blocks, UUT 456 x 320 mm
MG-07-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 456 x 320 mm (wxd)• Outer dimensions: 620 x 589 x 100 x 184 mm (wxdxh1xh2)• Equipped with dedicated cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
Product
Tribometers/Abrasion Testers
-
AEP Technology offers several ASTM, ISO DIN compliant friction and wear tester models optimized for various applications. The modular design allows it to run on one platform (rotary, linear reciprocating, linear, block-to-ring, etc.), and to ensure high repeatability, during the testing process our downward force friction and wear testing machine controls several standard tests. High-end electronics, multi-core 64-bit processor that allows it to use multiple in-situ sensing technologies (recording friction, wear, displacement, force, volume, temperature, humidity, position, speed, etc., during testing) with high resolution Embedded powerful platform imaging head (sections of atomic force microscopes, etc.). Ease of use and robust unique design make AEP Technology a powerful tool in friction and wear testing machine development and production environments.
-
Product
Mini Digital Output Pressure Sensor
DLHR Series
-
The DLHR Series Mini Digital Output Pressure Sensor is based on All Sensors' CoBeam2 TM Technology. This reduces package stress susceptibility, resulting in improved overall long term stability and vastly improves the position sensitivity. The digital interface option eases integration of the sensors into a wide range of process control and measurement systems, allowing direct connection to serial communications channels. 0.5 to 60 inH2O Pressure Ranges
-
Product
LVDS (Low Voltage Differential Signaling) Drivers and Receivers
-
LVDS (Low Voltage Differential Signaling) Drivers and Receivers from Analog Devices offers designers robust, high speed signaling for single-ended to differential solutions for point-to-point applications. Our selection of products conform to the TIA/EIA-644 LVDS standard and contain the first LVDS transceivers to meet 8 kV IEC ESD performance standards - important for robust, interboard applications where the connectors can be exposed to more harsh electrostatic environments. Companion differential line receivers and differential line drivers support up to 600Mbps. LVDS greatly improves noise immunity and minimizes emissions for high speed point-to-point data transmission and is a low power alternative to emitter-coupled logic (ECL) or positive emitter-coupled logic (PECL) signaling.
-
Product
Battery Monitor Relay
BMR
-
The Battery Monitor Relay contains over under voltage sensors combined with positive and negative ground detection.
-
Product
Centralized Motion Controllers
Motion Controller
Pulse train motion controllers generate high-frequency digital signals to control servo motors and steppers, matching performance and precision positioning of high-performance servo amplifiers.
-
Product
Equalizer
-
Chengdu KeyLink Microwave Technology Co., Ltd.
The series of products are mainly designed to complement the original system transmission characteristics of the curve.The frequency range covered by 0.5GHz~40GHz.Its characteristic curve can be designed into two types: positive and negative slope.The products have the characteristics of small size and high reliability.The products can be applied to all kinds of receiving and transmitting channels,high power traveling wave tubes, solid state power amplifiers, etc. KeyLink's equalizers can be categorized as follows.
-
Product
Global Standard Model For 4 Point Probe Sheet Resistance Automatic Measurement System
RT-3000/RG-1000F
-
*Fully automatic system for large sizes of flat panel with glass loading robot*Tester self-test function, Measurement position correction function, wide measurement range*Min. 0.1 mm meas. resolution and user programmable test pattern*Host (CIM) communication and 2-D/3-D Mapping software
-
Product
Single Photon Counting Camera
LINCam
-
Photon counting is the only way to get as much information brought by light as it is physically possible. Here we present the system allowing to detect not only arrival time of individual photons but also a position as straightforward as camera. Standing on the shoulders of night vision technology LINCam allows to extend any simple wide-field microscope to the powerful fluorescence lifetime imaging system.
-
Product
Wet/Wet Differential Pressure Transmitter
655
-
The Series 655 Wet/Wet Differential Pressure Transmitter converts a positive or a positive differential pressure measurement into a standard 4-20 mA output signal. Designed for use as a wet/wet differential pressure transmitter, units can be used to measure gas or liquid pressures compatible with 316/316L stainless steel wetted parts
-
Product
Target Wheels
-
Santa Barbara Infrared manufactures a wide variety of standard and custom target wheels, to conveniently and accurately position multiple targets in front of a blackbody source. The SBIR 300 Series Target Wheels are specifically designed to be used with SBIR’s standard differential blackbody sources and integrating sphere light sources. These motorized target wheels are available in several standard models to accommodate different sizes and numbers of targets.
-
Product
Thermal Abuse Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Thermal abuse test chamber protect for short circuit caused by incorrect operation of the operator and battery electrode, battery positive and negative connection, etc
-
Product
Carrier Acceptance Test Solutions for Network Operators
-
The Rohde & Schwarz carrier acceptance test systems provide access to the most important test plans of the world’s major mobile operators.Voice over NR, data throughput, protocol, positioning, RF, RRM and application testing – all relevant test scenarios are available on a common hardware platform.The entire range of 5G NR testing modes are available, covering sub-8 GHz (FR1) and mmWave (FR2) frequencies, and both non-standalone (NSA) and standalone (SA) modes.Contact your Rohde & Schwarz sales representative to learn more about the latest products and features.
-
Product
Linear Position
-
The linear magnetic position sensor product family measures the linear movement of a multi-pole magnetic strip. Circular multi-pole magnetic rings can also be used in rotary incremental rotation off-axis applications. This high precision product family allows the user to detect linear movement with a resolution as fine as 0.5μm. All products are aimed at applications which require extreme precision, accuracy, dynamic range and ultra-low power consumption.
-
Product
Integrating Sphere With Holder Base
IS-*MA
-
1. The hold base can bear max 20kg, it can expanding to test all lamps such as E27/E40, all tubes such as T5/T8/T12, and all kinds of luminaries2. The hold base can be installed in the ceiling or down, it can be adjusted the height3. Hold base has four power cables connect to the outside Power Supply and max is 5KW4. The holder base is detachable. For some kinds of light sources you may need to change the position of the holder base.5. Diameter: IS-0.3M (0.3m), IS-0.5M (0.5m), IS-1.0MA (1.0m), IS-1.5MA (1.5m), IS-1.75MA (1.75m), IS-2.0MA (2.0m). Other sizes can be designed according to the customer’s request.6. The painting of integrating spheres is according to CIE Pub. No.84 (1989)
-
Product
Magnetostrictive Level Transmitter
DM330
-
The Drexelbrook DM330 magnetostrictive level transmitter is a two wire loop powered intrinsically safe sensor with a configurable 4 -20 mA span.This level transmitter uses proven machine tool positioning accuracy combined with a process compatible float to offer a liquid level, and interface measurement system for the process industry.It comes in a patented low clearance design with all of the sensor’s electronics integrated in a 5/8” diameter sensing tube eliminating the electronics enclosure at the top of the sensor. Not only does this result in reduced cost it also offers its user greater options for insertion and mounting.The DM330 is available in two models.The rigid 316SS model offers a choice of a mini-connector or an optional housing including terminal connectors with zero and span adjustments.
-
Product
Drop Testers
-
This process is vital for ensuring that products travel to customers safely and securely, eventually arriving damage free. In turn, drop test systems help companies save money and maintain positive brand-owner reputations by helping to design packaged products that will deliver products with their intended inherent quality intact. Lansmont Drop Test Systems are the gold standard for accurate and repeatable drop testing. Every drop tester we manufacture is factory-tested to ensure it meets flatness-of-drop requirements and exceeds industry specifications.
-
Product
PCI-6601, 5 V, 4-Channel Counter/Timer Device
777918-01
Digital I/O
The PCI‑6601 performs encoder position measurements, event counting, period measurements, pulse-width measurements, pulse generation, pulse-train generation, and frequency measurement. It features four counter/timers, digital debouncing … filters, and TTL/CMOS-compatible digital I/O. The PCI‑6601 can perform one high-speed DMA transfer.
-
Product
Probe Card Analyzers
PB1500
-
The PB1500 is a low cost probe card analyzer system. It has the capability to perform all the tests done on the larger PB3600/6500 probe card analyzers, but at a lower cost for low pincount cards. A maximum of 1,280 channels may be configured in the PB1500 MUX system. The Precision Measurement Unit (PMU) has the same accuracy, repeatability and range as the larger analyzers. The repair process consists of selecting a failing probe, which moves it under the binocular microscope and positions a crosshair over the correct position for that probe.
-
Product
Object Detection Systems
-
Inside or outside: Effective solutions for an incredibly wide range of applicationsObject detection systems detect objects irrespective of size or position, both indoors or outdoors. They are used in intralogistics to increase throughput of conveyor systems. The systems also prevent collisions in outdoor areas and ensure and increase equipment availability in steel mills, ports and other areas. Regardless of the application, system reliability means smooth process flow.
