Positioning
Aligning test set with target geography.
-
Product
Planar-Doped Barrier Diode Detector, 0.01 to 50 GHz
8474E
-
The Keysight 8474E is a high-performance detector using a gallium arsenide, planar-doped barrier detecting element. It features extremely flat frequency response over its entire band of operation and very good frequency response stability versus temperature. The Keysight 8474E is also very rugged with high resistance to ESD damage. The Keysight 8474E detector is available with a 2.4-mm (0.01 to 50 GHz) connector. This detector offers the options for optimal square-law loads (Option 102) and for positive polarity output (Option 103). Because the unit-to-unit frequency response tracking of this device is typically better than plus or minus 0.3 dB, no matched response option is offered.
-
Product
PC104p-Chassis
-
The PC104p Chassis comes in two base sizes : 5 slots or 10 slots. The two models are adaptable to allow 1,2,3,4, or 5 cards to be mounted in the 5 slot unit and any number up to 10 in the larger unit. In a typical system the first position in the stack would be the power supply, the second the CPU and the rest IO or storage
-
Product
VTAC Patchcord, Receiver, SIM VTAC, 36", DACAR 636 Cable, Rosenberger Jack, 1 Position
7-142703731-036
VTAC Patchcord
VTAC Patchcord, Receiver, SIM VTAC, 36", DACAR 636 Cable, Rosenberger Jack, 1 Position.
-
Product
Quadrature Decoder Board
MSXB 050
-
The MSXB 050 Quadrature Decoder Board allows a Data Acquisition Processor to read quadrature-encoded signals through its digital port. Quadrature-encoded signals are often used to measure the angular velocity and angular position of wheels, gears, and motors.
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UUT 586 x 248 mm
MG-03-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 248 mm (wxd)• Outer dimensions: 750 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
Product
6 Channel 500 V/3 mA VME HV Power Supply
V6519
-
The V6519 is a 1-unit wide VME 6U module housing 6 High Voltage Power Supply Channels 500V, 3mA. The board is available with either positive or negative output polarity; mixed version with 3 positive and 3 negative channels is also available.
-
Product
PCB Connectors
C9394 Series
-
Smiths Interconnect's C9394 series is a high density, line removable module (LRM) connector available in 132 through 594 positions, that can be configured to include fiber optic and coax options.
-
Product
PCI Pulse Position Data Communication Board
MS 1708
-
*Bus Interface - PCI Bus*Micro controller Based Design*Shared Memory for Communication*8 Channels RS422 / Modified RS422*PPD (Pulse Position Data) Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS*Independent Intelligent Devices for RS422 and PPT Communication
-
Product
IO-Link Position Sensors
-
*Capacitive sensors for position detection or level monitoring*Distance sensors with very long range and background suppression*Ultrasonic sensors for non-contact detection of objects*Photoelectric sensors for specific applications*With switching output, analog signal and IO-Link
-
Product
CSlaser | CTlaser Series Infrared Thermometer
-
The infrared thermometers of the optris CSlaser/CTlaser series consist of an innovative double laser sighting, in contrast to many IR thermometers with single lasers which only mark the center of the spot. The two laser beams follow the infrared optical path to mark the position of the measuring field at any distance. At the focus point both lasers are crossing – this greatly supports an exact alignment and reduces measurement errors. The infrared thermometers of this class are mainly used in industrial areas as well as in research and development. Small measurement field sizes are of great importance for precise temperature measurement. A number of different focus versions allow a flexible adjustment for the different applications.
-
Product
Fully Automatic 4 Point Probe System for Silicon Wafer
WS-8800
-
*Measurement of resistivity, thickness, conductivity(P/N) and temperature*Tester self-test function, wide measuring range*Thickness, measurement position and temperature correction function for silicon resistivity*Number of cassette station can be changed by customers request*Host (CIM) communication and SMIF or FOUP compatible
-
Product
Automatic Double Drop Test Machine
DT-JT
-
The machine wills automatic stop positioning after sample reach up to the sated height position. According to the different size to choice the test distance between tests arms, electric pulse width. The release mechanism of machine are flexible and reliable, to ensure the sample without any external influence during the release of instant and free fall way, and make sure it meet sample’s dropping requirements. It is according to GB4757.5-84), GB/T4857.5-92, GB/T2423.5, IEC68-2-27, JISZ0202-87, ISO2248-19, ISO2248-1985(E, ASTMD5276-1998 and ISTA3A. This series drop test bench for measuring the main simulation packages in the transportation, loading and unloading process under drop impact influence, identification package impact strength and packaging design.
-
Product
Differential Pressure Transmitter
608
-
The Dwyer Series 608 Differential Pressure Transmitters convert positive, negative (vacuum), or differential pressures of clean, dry air or other non-conductive, non-corrosive gases into a standard two wire, 4-20 mA output signal
-
Product
Desktop Test Interface Station
2210
-
TESCO’s new Desktop Test Interface Station (Catalog No. 2210) provides metering professionals with exceptional testing flexibility. The Test Interface Station is ergonomically designed for meter technicians working in a lab or a desktop, yet still rugged for field use. The Test Interface Station includes a zero insertion force (ZIF) meter socket, voltage selection, form selection, open/closed-link selection and bi-directional cabling to power a load box/test kit & connect test standard potentials. When combined with a test kit/test standard and powered via 120 VAC, the Test Interface Station creates a single position, stand-alone, meter accuracy testing device for various socket based meters (both mechanical & solid-state).
-
Product
Brushless Resolvers
-
Computer Conversions Corporation
Computer Conversions GT transducers are brushless, Electromagnetic, Rotary Sensors used to provide Precise Absolute or Incremental Position, and Velocity feedback in harsh environments. All Computer Conversions Transducers are continuous rotation, bi-directional, and electronically passive devices (no electronic components to degrade or fail), that require zero maintenance, and may be installed in virtually inaccessible locations.
-
Product
DC Safety Inspection Device For Solar Panels
“DC Fault Tester”
-
Identifies defect position instantly- contributes to saving inspection time
-
Product
20/26 Ghz Coax, Module Insert, Receiver, i2 MX, 5 Position
510143008
Receiver Module Insert
20/26 Ghz Coax, Module Insert, Receiver, i2 MX, 5 Position.
-
Product
VFD / Inverter Meter
-
Engineered specifically for troubleshooting Variable Frequency Drives and Power Inverters the Talon VFD / Inverter Meter is your key to positive results. Not only that, this meter is easier to use than a standard multi-meter and can save more money than it costs the very first time you use it to fix a piece of equipment instead of replacing it.
-
Product
Audio Frequency Oscillator
PD-5
-
2.5- 100 volt output6 position output voltage selectorCompatible with all "Mark" receivers (Mark II, III, IV, V)Pulse "Identifying" signalBattery charging circuit built-inLED impedance meter
-
Product
Absolute Optical Inclinometer
A2T
-
The A2T is a single axis, digital gravity angle sensor. The A2T serves as a full 360 range absolute tilt sensing programmable level with either digital or analog output. Internally, a rotary bar coded disk is mounted to a weighted gravity driven wheel. A micro-controller strobes an LED to transfer the bar code image onto an optical linear array, then decodes the position every 2 mSec. Magnetic damping provides fast response and settling time while virtually eliminating overshoot and oscillations. An internal EEPROM stores field programmable parameters such as resolution, zero position, direction swap, and mode. This second generation design virtually eliminates the primary accuracy limitation of first generation inclinometers, which is sitation (hysteresis).
-
Product
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Crimp
510143002
Receiver Module Insert
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Crimp.
-
Product
HPLC Pump
LD Class
-
The versatile LD Class consists of dual-headed, positive displacement piston pumps, delivering unmatched performance for analytical, flash, and small-scale preparative chromatography applications. With the patented SSI low dead-volume Pulse Dampener, advanced cam technology and dual piston mechanism, the LD Class provides virtually pulse-free operation.
-
Product
Precision Targeting Systems
-
Designed to meet the various missions of the United States military, the Common Laser Range Finder-Integrated Capability (CLRF-IC) provides rugged day and night capabilities for reconnaissance, surveillance, and targeting operations. Within a three pound package, the CLRF-IC employs the latest in advanced and lightweight handheld technologies. Featuring a Single Wave-IR night camera, high definition color day camera, eye-safe laser rangefinder, digital magnetic compass and a global positioning system, CLRF-IC increases precision targeting capabilities. Powered by either L91 or CR123 batteries, the system recognizes targets over 3 kilometers in day light and1 kilometer at night.
-
Product
EZ-Glider Position Control Torque Arms
-
Equipped with position encoders, the position control torque arm is an error-proofing system that detects and eliminates costly screw-fastening errors during the assembly process. The poka-yoke system reduces the risks of improperly fastening screws, ensuring that every screw is correctly tightened in the correct sequence. In critical applications, tightening fasteners in the correct sequence ensures the reliability of the joint. The position control system is like putting the eyes and ears of a quality control manager where they are needed most – right at each work station.
-
Product
ADVANCE | Drop Shape
-
ADVANCE is an example of how even the most complex measuring tasks, such as determining the surface free energy (SFE) of a solid, can be represented on a clear and easy to use interface. With just a few intuitive editing steps you can prepare software-controlled contact angle measurements utilizing every degree of automation up to complete SFE measurement, position mapping, or tilting experiments. Using our Liquid Needle dosing technique, ADVANCE even accesses the SFE of a surface within just one second.
-
Product
Tensile Compression Force Tester
ESM303
-
The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMeTM force-based positioning - using your hand as your guide, push and pull on the force gauge or load cell to move the crosshead at a variable rate of speed.
-
Product
Signal/Micro Power/Micro Coax, Module, Receiver, TriPaddle, 90 Series, 20/20 Position
510104323
Receiver Module
Signal/Micro Power/Micro Coax, Module, Receiver, TriPaddle, 90 Series, 20/20 Position.This hybrid module provides 20 TriPaddle Signal positions and 20 Micro Power or Micro Coax positions in a single wide module slot enabling consolidation of wiring and preserving valuable space in the Receiver.*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
Dimensional Metrology Systems
-
We are a global provider of optical industrial measurement technology for quality assurance of complex components with tight tolerances. With Bruker Alicona measurement systems, users measure dimension, position, shape, and roughness by using only one optical sensor. Measurement systems are applied in both research and directly on the shop floor.
-
Product
PXIe-6614, 5 V, 8-Channel, Precision Reference PXI Counter/Timer Module
782353-01
Counter/Timer Module
PXIe, 5 V, 8-Channel, Precision Reference PXI Counter/Timer Module—The PXIe‑6614 is a high-precision counter/timer module that performs encoder position measurement, event counting, period measurement, pulse-width measurement, pulse generation, pulse-train generation, and frequency measurement. It features eight counter/timers, digital debouncing filters, and TTL/CMOS‑compatible digital I/O. The PXIe‑6614 offers industrially rugged features for a wide array of applications such as automotive/aerospace, industrial/motion control, and manufacturing test. Measurements are highly accurate and precise over longer periods of time because of the oven‑controlled crystal oscillator (OCXO) in the module.
-
Product
sbRIO-9221, Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781115-01
Voltage Input Module
Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the sbRIO‑9221: a 36‑position spring‑terminal connector and a 37‑position DSUB connector. Non-enclosed modules are designed for OEM applications.
