DC Electronic Loads
The current that results from resistive elements of the load on an output.
-
-
Product
Advanced Power System - Dynamic DC Power Supply, 20 V, 100 A, 2000 W
N7971A
DC Power Supply
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
Product
DC Power Supply
PW-3033R
-
*Toroidal Transformer*Low EMI & High EMS*Very Low Ripple & Noise*30V/3A+30V/3A+5V/3A Triple output.*Tracking operation.*<0.3m Vrms Ripple & Noise(C.V.)*<2m Arms Ripple & Noise(C.C.)*4 Display.
-
Product
Load Pull Test Fixtures
-
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
-
Product
VME/VME64x Load Board
-
VECTOR Electronics and Technology, Inc.
The 6U VME and VME64x load board functions to test a system’s cooling capability by applying a variable load to the power supply for verification, then generating necessary heat to confirm the chassis’ cooling. This enables locating hot spots in the chassis so the airflow can be properly directed.
-
Product
DC Coupled Current Probe
34134A
High Current Probe
Measure a wide range of applications with this battery-powered, clamp-on probe; use with DMMs or voltmeters
-
Product
Radar Electronic Support Receiver
RR024
-
The RR024 is designed for Radar Electronic Support (RES) and Radar Warning Receiver (RWR) applications where high performance and small size are of prime importance, with filtering, amplification, detection and pulse parameter measurement being combined into one multi-function unit. Four amplitude measurement channels allow direction finding by amplitude comparison between adjacent antennas. An IFM, fed from one of the amplitude channels via an SPDT switch, performs 14 bits of frequency measurement on the selected input. Frequency resolution is nominally 1 MHz over a 2 to 18 GHz band.
-
Product
Unclamped Inductive Load Tester
ITC55100STD
-
Model ITC55100STD performs ruggedness testing of power MOSFETs and IGBTs. It also tests single and dual diodes, and forward and reverse bias of IGBTs when used with an optional ITC55-RSF Output Selector Box.
-
Product
Air Core Line & Load Reactors
-
Line and load reactors are generally serial-connected to the input and/or output terminals of three phase equipment such as motor speed controllers, inverters and UPS systems. These equipment make use of semiconductor switches such as IGBTs, thyristors, and diodes and therefore create harmonic distortion and high switching over-voltages (dv/dt). Use of such equipment has been becoming more widespread as the technology advances. However, the negative effects of these equipment should not be overlooked.
-
Product
LOAD CELLS From UTILCELL
-
For more than 35 years, UTILCELL has been the national market leader for load cells and is now one of the five leading manufacturers in the world. The load cells are used in small scales, personal scales or retail scales, industrial scales, filling and packaging scales, truck and train scales and other applications.
-
Product
Digital Electronic Tyre Pressure Gauge
6515
-
Peaceful Thriving Enterprise Co Ltd
To measure tyre pressure, measuring range: 5-150 PSI.
-
Product
DC Power Supply
PW-3063R
-
*Use Toroidal Transformer. Low EMI & High EMS.*Triple output, 0-32V/0-6A X2 and 5V/3A .Max. 400Watts*Tracking operation. Max. output 64V/6A on tracking series or 32V/12A on tracking parallel.*4 display, Green LED shows Voltage and Red LRD shows Current. Easy to read.*Compact design. G.W. 9Kgs only. Easy to handle.*The resolution of PW-3063R as high as 0.1v and 0.01A.*Very low Ripple & Noise, less than 0.4mVrms. Very suit for precise measurement.
-
Product
24V / 400 Amp Load
EL12-24M
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely cost effective.
-
Product
Semiconductor & Electronic Systems Test and Diagnostics Services
-
Reliability Test and Diagnostic services are offered to a wide range of customers that are active as Fabless Semiconductor or Integrated Device Manufacturers, automotive electronics supplier, Telecom and ICT application specialists, Industrial and Medical electronic system manufacturers or in Aerospace and Space applications. Independent high tech test and diagnostic service laboratory. IC and electronic module qualification. ESD and Latch Up testing. Design assessment by HALT/HASS. Failure and construction analysis.
-
Product
Programmable DC Power Supply
IT6100 Series
-
IT6100 series assure you accurate measurements with 0.1mV/0.1mA high resolution and high accuracy. With high-speed List mode output and voltage rise speed up to 20ms, it can independently edit and perform the default voltage waveform to meet the high-speed test needs. IT6100 series has built-in 5 1/2 digital voltmeter and milliohm meter, which can measure additional signals. IT6100 series supports SCPI communication protocol, GPIB/USB/RS232 interfaces are optional for customers.
-
Product
250 Watt Electronic Load Module
N3303A
Load Module
The Keysight N3303A is a 250 W (0-10A, 0-240V) electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3303A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3303A can also digitize waveforms.
-
Product
DC Resistance Tester
DCSS502BC
-
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
Product
Electronic Boards
-
Computer Gesteuerte Systeme GmbH
The relay board 8AGN is a cost-effective board of the CM series, which is also used in our load modules, for example. It can be mounted on a 35 mm DIN rail. Currents up to 1 A at 30 V are possible. The maximum wire cross-section is 0.5 mm².
-
Product
Electronic Circular Temperature Chart Recorder
-
The Circular Temperature Chart Recorder’s external stainless steel probe allows you to measure the temperature of air, gas, liquids and semi-solids. The temperature chart recorder has a quartz clock movement, motorized chart advance and temperature accuracy of ±2°F (±1°C). The chart recorder comes in °F or °C models and runs on 120V or 220V AC, 50/60 Hz. A rear compartment houses 8 AA alkaline batteries, providing up to 48 hours of continuous recording in the event of a temporary power loss.
-
Product
Hand-Held/Digital Load Tester
6030
-
• Full 125 Amp load tests 12 Volt batteries, alternators and starters on all type of vehicles• PATENTED• Made in USA of US and Global Components
-
Product
Electron Probe Microanalyzer
EPMA
-
JEOL commercialized the world's first FE-EPMA, the JXA-8500F in 2003. This highly regarded FE-EPMA has long been used in various fields, such as: metals, materials and geology in both industry and academia. The JXA-8530FPlus is a third-generation FE-EPMA that comes with enhanced analytical and imaging capabilities. The In-Lens Schottky field emission electron gun combined with new software provides higher throughput while maintaining high stability, thus allowing a wider range of EPMA applications to be achieved with higher resolution.
-
Product
Modular DC Power Supply
62000B
-
Chroma Systems Solutions, Inc.
Chroma’s 62000B series of Modular DC Power Supplies offer 5 types of power module with ranging from 1V to 150V, current from 10A to 90A, and offers two mainframe type of six and three position. The six position mainframe can envelop in up to six power modules paralleled operation for 9KW power output. The 62000B can easily parallel up to 14 mainframes to 120KW with current sharing and CAN bus control for bulk power applications.
-
Product
Electronic Engine Instruments
-
Is a flight instrument display system in an aircraft cockpit that displays flight data electronically rather than electromechanically.
-
Product
Electronic Outside Air Temperature
OAT
-
The outside air temperature sensor is an electrical component that complements the control of a modern heating system.
-
Product
Electronic Drum Latency
-
EDLM iPhone app was developed specifically for measuring latency in electronic drums. It connects to the input and output points of an e-drum system and provides automated and accurate latency measurements.
-
Product
Portable Three-Phase Phantom Load
EE-120A-3 + EE-500V-3
-
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. The generated values of voltage, current, power, power factor, phase shift, THD and frequency are indicated on the LCD display.
-
Product
DC Energy Meter
-
Multiple channels can be measured by a single meter, EN2450N & EN2450D. Differential current input for all the current channels. Programmable shunt secondary 50mV to 100mV. Programmable CT Primary for all channels up to 200A - for Hall Effect CT. Data logging for parameters such as Energy, Load hours and Ampere hours. Easy installation,Compact size, weight and simple wiring.
-
Product
DC Coupled Differential Switching System
BS1553F(X)
-
Universal Switching Corporation
The BS1553F(X) is a modular passive DC coupled differential switching system. It is designed as an automated "patch panel" for interconnecting numerous MIL-STD-1553 devices, cables and hardware, or for routing other differential signals such as '422 clock/data or kelvin ATE measurements. The I/O capacity is scalable from a small 8x8, up to 64x64 in one 5RU unit.
-
Product
PCRF Load Tester
-
The Polaris Networks LTE PCRF Load Tester is a comprehensive test solution for evaluating the performance and the stability of LTE Policy and Charging Rules Function. The PCRF Load Tester is ideally suited for manufacturers of PCRF equipment as well as operators deploying PCRF in an LTE network. The Tester can be used for testing both the Control Plane and the User Plane under various load conditions and for measuring the capacity and various key performance indicators of EPC nodes. The Tester simulates millions of Subscriber sessions with multiple bearers per Subscriber.
-
Product
Programmable DC Power
XR Series
-
The XR Series utilizes the latest IGBT devices to drive down size and increase performance. The high frequency design delivers fast transient response and low output ripple. This performance coupled with Magna-Power''s rugged current-fed power processing, enables confidence in even the most demanding applications.
