Backplanes
An interconnection structure allowing multiple printed circuit boards to coexist using a single bus.
-
Product
3U OpenVPX 2-Slot Backplane With 1 VPX Power And Ground Plus 1 VITA 62 Power Supply Slot
101VPX302P-2X13R
-
This 3U Open VPX backplane offers one VITA 46 Power and Ground slot and one VITA 62 power supply slot to support the development and deployment of systems requiring a VITA 62 power supply. The rear power studs can be used to connect to an adjacent backplane to feed it power.
-
Product
VPX Chassis 4U/42HP 5 Slots Desktop
-
This 5 slot Hartmann VPX 4U desktop system chassis provides a portable packaging solution for high-performance processors on a full mesh backplane topology. The 42HP wide desktop enclosure for vertical mounting of boards is outfitted with a 300W ATX power supply and a 1U fix bottom mounted fan tray.
-
Product
Rack Mount Osprey Chassis 5.25" Qbus
97106-Q
-
5.25" high by 19" wide by 20" deep (134 x 483 x 508 mm), this chassis is FCC/CE certifiable**. A quad-height Qbus backplane, cooling fans, and slides are provided, diskette and hard drives (two visible 5.25" and two hidden 3.5" bays), and up to four quad-height Qbus compatible cards.
-
Product
cPSB 2.16 20 Slot + 2 bridges
107PS21620-0157R
-
CompactPCI CPSB 2.16 6U 20 slot, with 2 bridges, fully compliant to the PICMG 2.16 Packet Switching Backplane specification.
-
Product
F9 Systems CalBlade
-
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
Product
MTCA.4 Power Supply
-
To match the requirements of the next generation of “carrier grade” communication equipment the PCI Industrial Computer Manufacturers Group PICMG created in 2002 a new standard AdvancedTCA / ATCA. The ATCA crate backplanes are based mainly on 48V industrial power supplies. From this form factor evolve the Advanced Mezzanine Module carrier card AMC form factors defined in AMC.3 in types of single or double width.
-
Product
Backplane Test System
402LV
-
Very High Pin Count Level IV Backplane Test System. To ensure that Testronics maintains its leadership position as the premier supplier of backplane testers, we will be introducing our solution to testing high pin count / very large backplanes, the Model 402.
-
Product
Cost-Effective Wallmount Chassis
IPC-7132
Chassis
Cost-effective Wallmount Chassis for ATX/mATX Motherboard and 10-slot Backplane. Support ATX/mATX M/B and 10-slot PICMG 1.3 backplane, Shockproof drive bay for one 5.25" ODD and three 3.5" HDDs. Thumb-screw for top cover easy opening, Bidirectional option to mount chassis on wall or workbench.
-
Product
SATA Drive Carrier
SD1-DISCO
-
The SD1-DISCO is a peripheral slot card for CompactPCI® Serial systems. The board accommodates a 2.5-inch size SATA drive, controlled by the SATA channel derived from the backplane connector P1.
-
Product
PCI/PCI Express Expansion Backplane
SKU-075-0X
-
PCI/PCI Express Expansion backplane was designed as a universal solution for Desktop or Laptop host computer expansion.It allows adding up to 4 PCI and up to 2 PCI Express boards to the host computer. Expansion backplane can be placed inside any general-purpose computer chassis and connects to the host computer via 5ft (or 10ft) CAT6 cable.
-
Product
OpenVPX Cable Solutions
OPENVPX-CABLE
-
Compliant to VITA 46 and 65, the cabling assemblies are ideal for development. They can be used for I/O to bulkhead connectors and slot-to-slot connections. Front-plug versions allow testing across the backplane or full interconnect path.
-
Product
3U VPX Development Kit
Software Development Kit
This development kit enables efficient 3U VPX backplane design and software verification.- 3U VPX architecture- One CPU blade, one GPU blade (optional), SOSA-aligned- 1TB NVMe pre-installed in CPU blade- Rear transition module(s) included- Test Frame with backplane pre-installed
-
Product
PCIe X8 And X1 Bridge Card
-
The Guzik PCI Express Host Interface Bridge Card was designed to expand the x8 PCI Express Gen 2 (PCIe) slot in a host PC to an AXIe or a Guzik GSA 6000 chassis via a x8 PCI Express Gen 2 and a x1 PCI Express Gen 1 high speed PCI-SIG specified data cables. This allows the end node to connect to the host bus at speeds up to 3.2GByte/sec user data rate. The Bridge Card installs in a x8 or x16 slot of a PCIe backplane or a PCIe motherboard, provides additional board-based retention and reinforced front panel.
-
Product
10 Gbit Ethernet Card, PXIe Form Factor
ADQ10GBE
Ethernet Interface
The ADQ10GBE module enables fast network connection from a cPCIe/PXIe chassis to an external host computer. It occupies a single slot in an 3U cPCIe/PXIe chassis and can be used with backplanes supporting up to x8 Gen2 PCIe. All necessary software drivers are included and can be installed on the PXIe controller. ADQ10GBE can be used under Windows 7 (32 or 64 bit), Windows 8 and 8.1, and Linux (native support or ixgbe source code).
-
Product
Extrusion Rail
5250998-84
-
VECTOR Electronics and Technology, Inc.
Fits onto rear face of rear extrusion rails, in between backplaneand extrusion rail to isolate backplane from extrusion.HP pitch pattern of holes for precise installation of backplane.
-
Product
ATCA 5U 5 Slot Mesh w uTCA connector for SHMM
109ATCA505-9020R
-
The 5U 5-slot ATCA backplane is a 3X Replicated Mesh. However, Dual Star, 1X and 2X Meshes can all be implemented across the 5-slot backplane.
-
Product
8-Slot 64-Bit 6U CompactPCI Backplane
cBP-6408R
Backplane
- PICMG 2.0 CompactPCI Specification R3.0 Compliant- PICMG 2.1 CompactPCI Hot Swap Specification R2.0 Compliant- PICMG 2.5 H.110 Computer Telephony Specification R1.0 Compliant- Design for 64-bit/33MHz CompactPCI computer system application- One system slot with seven expansion slots, system on right hand side
-
Product
VME J1 20 Slot with ADC Connectors
101VMEJ120-0590R
-
VME J1 backplane 20 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME64X 6U 12 Slot with P0
101V64XC12-1621
-
6U VME64x Backplane 12-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension standard. Includes termination passive inboard, daisy chain automatic active, and power bugs on top and bottom of slots.
-
Product
Dual-Site Single-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier
6332
-
Our Dual-Site Single-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier 32-Bit/66 MHz (6332) adapts two single-wide PMCs to a cPCI slot. At the heart of the carrier is a 6150 PCI-to-PCI bridge that connects the carrier's internal PCI bus to the cPCI backplane.
-
Product
3U CompactPCI Enclosure with 6-Slot Backplane and Redundant Power Modules
cPCIS-3048
Backplane
- 3U CompactPCI backplane with one system slot and five peripheral slots- Suitable for rackmount applications- 3U 48HP fanless enclosure- Optional redundant CompactPCI power modules
-
Product
cPCI 3U RB
-
Hartmann’s cPCI 3U RB Series Backplanes utilize a board design based on the HIGH-SPEED DESIGN concept. Low reflection is achieved by means of uniform signal surge impedance.
-
Product
Others – Carrier Modules
-
To complement the wide range of interface modules for dedicated Avionics Databuses and Networks, AIM offers a range of Carrier modules for the use of AIM or any 3rd Party PMC and XMC module on various backplanes.
-
Product
ATCA 5U 14 Slot Dual Star 40G - With Radial IPMB
109ATCA514-0013R
-
The 5U 14 slot ATCA backplane is a dual start with radial IPMI, designed to meet 40Gbps (4 x 10G ports) data rates. Elma's ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
Product
AdvancedTCA, Type 11A, 5U 19" Horizontal, AC
11A05FJB58Y4HGBX
-
Elma's ATCA, AC, 5U horizontal enclosure with backplane, and shelf mgmt. options. Pluggable and redundant fan trays, PEMs and shelf managers for availability (99.999%). Optimized via backplane signal integrity studies and chassis thermal simulation.
-
Product
VME J1J2 Monolithic 6 slot
101VMEM106-0500R
-
VME J1J2 Monolithic backplane 6 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
XMC Module Carrier PCI Express x 8
SK4-WALTZ
-
SK4-WALTZ is a bidirectional 8-lane PCI Express® Gen3 redriver, for optimum high speed signal integrity, and should be installed into a fat pipe peripheral slot of a CompactPCI® Serial backplane.
-
Product
PICMG 1.0 Full-Size Single Board Computers
Single Board Computer
PICMG 1.0 Single Board Computers (SBC) features comprehensive backplane support. The Slot SBC are the most flexible and expansible solutions for industrial applications.
-
Product
VME J1 16 Slot with ADC Connectors
101VMEJ116-0590
-
VME J1 backplane 16 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
CompactPCI Chassis 2 Slots
Chassis
Hartmann CompactPCI 1U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides a 2 slot 5V I/O 6U cPCI backplane for horizontal mounting of boards. This system is designed with enhanced EMC features.
