WiFi Detector
Locate wireless internet signal.
-
Product
CO Detectors
-
UEi Test & Measurement Instruments
A device that detects the presence of the carbon monoxide (CO) gas to prevent carbon monoxide poisoning.
-
-
Product
Multifunctional Cable Detectors
-
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA Multifunctional Cable Detector has a very high cost-effective, it can quickly trace and identify UTP/STP RJ45/ RJ11/BNC/ metal cable.
-
Product
Refrigerant Detectors
-
UEi Test & Measurement Instruments
Is designed and certified to meet the new tougher standards and detect the latest refrigerants.
-
Product
Planar-Doped Barrier Diode Detector, 100 kHz to 2 GHz
8471D
-
The Keysight 8471D is a low-cost, planar-doped barrier detector offering excellent performance to 2 GHz. A negative polarity output is standard, and a positive polarity is available as Option 103. A load option (Option 102) extends the square-law region to at least -10 dBm. The Keysight 8471D has a BNC (m) input connector and a frequency range of 100 kHz to 2 GHz, making it ideal for use in RF and low microwave applications.
-
Product
Spatial Heterodyne Surface Chemical Agent Detector
SHSCAD
-
Wide area, high areal coverage rate surface contaminant detection via LWIR reflectance spectroscopy employing eye safe broadband quantum cascade lasers (QCLs) and a high-speed spatial heterodyne spectrometer (SHS) in a handheld sensor package (~ 10,000 cm3, 10 lb).
-
Product
Hostless Wi-Fi IoT Module
SX-ULPGN-DB
-
The SX-ULPGN-DB is a low-power , cost effective hostless Wi-Fi IoT module with 802.11 a/b/g/n support. This low power Wi-Fi IoT module is based on QCA4012 radio from Qualcomm. SX-ULPGN-DB is a feature-rich intelligent Wi-Fi solution for IoT that integrates a full Wi-Fi stack, full networking/security stack, and embedded CPU and memory for on-chip application development.
-
Product
X-Ray Seamless Pixel Array Detector
XSPA-400 ER
-
In general, X-ray diffraction measurements using a Cu X-ray source are known to have difficulty detecting trace crystalline phases because of increased background when measuring samples containing transition metals. The high energy resolution of the XSPA-400 ER supresses the fluorescent X-rays originating from the sample, thereby reducing background, enabling highly sensitive measurements of samples containing transition metals, such as iron and steel compounds and battery materials.Therefore, it achieves higher sensitivity measurements than conventional detectors.
-
Product
Detector Modules
-
Detector modules, into which the entire drive electronics have been integrated, were developed to facilitate the application of detectors. PIN modules and APD modules are available along with intelligent sensors which are – thanks to their interfaces – ready for application in Industry 4.0.
-
Product
Refrigerant Leak Detectors
-
refrigerant leak detectors use a proprietary semiconductor sensor to detect most commercially available HFC, HFO, HC, HCFC and CFC refrigerants. Our newest model, the RLD440 Refrigerant Leak Detector, goes one step further by complying with all five worldwide refrigerant detection testing standards
-
Product
Hand Held Metal Detectors
-
Handheld metal detectors (also known as ‘metal detection wands’) for use in conjunction with metal detector archways or in isolation for certain applications.
-
Product
Near Field Moving Detector Goniophotometer
LSG-1900B
-
LSG-1900B Goniophotometer is near field Type C automatic goniophotometric instrument for luminous intensity distribution measurement. The LSG-1900B uses a constant temperature detector. It is for industrial laboratory photometric data measurements of small luminaires, such as down light, bulb light, etc.
-
Product
RF Detectors for Millimeter Wave
-
RF Detectors are essential microwave/millimeter wave products for most Tx (transmit sources). Transmitter output power measurement is the main application. It is essential to know the RF output power because the output power level must not go above values set by FCC regulations.The unit of power is the watt for RF detectors. But, most commonly used in most RF and wireless systems to express power is the terms of dBm or decibels related to 1 mW:View more RF Detector
-
Product
Fixed Gas Detectors
700 Series
-
Teledyne Gas & Flame Detection
The sensor electronics are completely protected and immune to water ingress and corrosion. The sensor elements are all plug-in components and can easily be replaced in the field. Operator interface is non-intrusive via a small handheld magnet. Configuration and routine calibration is intuitive and menu driven with fully scripted instructions. Sensor status is displayed on a built-in alphanumeric LED display. The 700 Series intelligent sensor modules feature dual redundant outputs, a linear 4-20 milliamp analog signal and a Modbus RS-485 serial output.
-
Product
Dynamic X-Ray Detector
Shad-o-Box HS
-
The Shad-o-Box HS family of x-ray detectors are high-performance, high-resolution x-ray imaging devices designed for high speed digital radiography applications. Each model combines our x-ray sensor modules with appropriate readout electronics and a 14-bit digital interface for easy connection to a PC. The high-speed digital connection allows real-time imaging at frame rates up to 66 fps, while the state-of-the-art CMOS technology offers superb contrast, dynamic range, and resolution.
-
Product
Temperature Measurement IR Sensors & Detectors
ST120 TO-5
-
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 1.2mm x 1.2mm in a TO-5 package. Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
Open Path Infrared Detector
Ultima OPIR-5
-
Get continuous monitoring of methane, propane, and other combustible gases with this open path infrared detector. Provides 4-20 mA analog signals, as well as digital display and relay contacts.
-
Product
Portable Gas Leak Detector
Oxygas 500
-
Teledyne Gas & Flame Detection
The Oxygas 500 compliments the Gascoseeker 500 with a similar performance, measuring % LEL and % volume flammable hydrocarbons, but with the addition of oxygen for either gas/air or gas/nitrogen/air purging. The Oxygas 500 has the following additional features; automated zero during start-up, manually selectable purge mode.The P-500 variant has an additional part per million (ppm) range of methane.The Oxygas 500 is easy to use with very simple training, as the operation of the instrument follows the operation of the purge cycle. The rugged design allows the Oxygas 500 to be used in harsh environments. The instrument is also fully compatible with our range of calibration software and equipment.
-
-
Product
Amplitude Detectors with Isolators
-
Full band waveguide detectors are GaAs beam lead Schottky diode-based detectors that are specially designed for millimeterwave network analyzer applications. With a proprietary circuitry design and careful diode selection, these zero-biased detectors exhibit high sensitivity and extremely flat output characteristics. The below standard offering covers the frequency range of 18 to 170 GHz and offers a 1 MHz video bandwidth and 1 MΩ video output impedance. The standard models also have the capacity to handle a maximum RF input power of up to +17 dBm. The RF interface of these detectors is a standard waveguide with an integrated Faraday isolator to improve the port VSWR. The output voltage polarity is negative and the connector type is a female SMA. Other configurations are offered as custom models.
-
Product
Electrochemical Detector
800D
-
The Model 800C series is designed for electrochemical detection. This instrument can be used for monitoring the current passing through a flow cell in liquid chromatography/electrochemistry and in-flow injection analysis, as well as other electroanalytical applications.
-
Product
Multi-Angle Light Scattering Detector
PN3621
-
Since the 1990s Postnova has been a leading innovator and developer of special advanced online Light Scattering solutions for coupling with chromatographic separation systems. The first model was the PD2000 - Static Light Scattering detector for coupling with Asymmetric Flow FFF. Later on the models PN3020 SLS and PN3070 MALS have been launched. Based on these over two decades of practical experience, Postnova has collected a unique competence in the area of Laser Light Scattering and has developed the unique PN3621 MALS - Multi-Angle Light Scattering detector series. The model PN3621 MALS is a completely new type of high performance MALS detector system with a unique range of specifications.
-
Product
IMSI Catcher Detector
-
IMSI Catcher detector allows detection of the presence of any active cellphone interception system in the near vicinity. Can be used as area sanitisation tool in a restricted areas before arrival of any VIP.
-
Product
Gas Detectors
-
Inspecting and detecting gas leaks in industrial and/or commercial settings is an important element of maintaining security. GAOTek gas detectors are compact, lightweight, and easy to carry. When you choose an industrial-grade GAOTek gas detector, know that you can rely on it to deliver accurate information with real-time readings on how much the concerned gases are in the air, ensuring the safety of your premises and anyone occupying the space is upheld.
-
Product
Laser Open Path H2S Detector
GD1
-
Teledyne Gas & Flame Detection
The GD1 has been designed with features that provide an effective response to the detection of gas hazards in a wide range of industrial environments from offshore production facilities to wastewater treatment plants. At the heart of the detector is a tuneable laser diode that eliminates environmental effects from sun, rain and fog. The laser scans single absorption lines where there is no interference from other gases.The GD1 needs no recalibration and can replace multiple standard detectors to cover the same risk. The complete optomechanical design and construction is so stable that an ultra fast speed of response can be achieved while providing unparalleled service life and detector stability, thus saving on maintenance and service costs.Supplied with worldwide hazardous area approvals. Suitable for use in systems with SIL 2 requirement.
-
Product
Special Detectors
-
Single channel enhanced IR detectors with fast response, extended gain, and/or high modulation frequency range for applications in spectroscopy and analytical instruments.
-
Product
X-Ray Detectors
-
With the need to always reduce the inspection time to the strict minimum, the NDT world is slowly reducing its dependency on films and jumping straight into the Digital Radiography (DR) revolution. While saving tremendous amount of time and money not developing films, digital radiography also enables you to edit, record and send your inspections to whomever, whenever and wherever you want.
-
Product
In-Plant Holiday Detector
In-Plant Holiday Detector
-
High Voltage Holiday DetectionPulse DC OutputLow Settings: 800v to 8,000vHigh Settings: 3,500v to 35,000v110v / 220v AC Power SupplyIntegrated Digital Volt MeterVisual (LED) Holiday IndicatorAudible Holiday IndicatorRemote Indicator Connection, Audible and Visual
-
Product
WiFi Oscilloscope Probe
IkaScope
-
IkaScope is a wireless oscilloscope probe. It fits perfectly in your hand and works with any connected screen, like a laptop, a tablet or smartphone. Thanks to ProbeClick® technology, IkaScope knows when to measure and when to hold. IkaScope transfers measured signals over high speed wifi connection. 200 MSa/S Sampling rate. 30 MHz Bandwidth. 80 Vpp Input range. AC/DC Coupling. 4000 ptsMemory. 200 FPS Max. refresh rate.
-
Product
Interceptor Metal Detector
-
Interceptor metal detectors are custom manufactured to achieve superior results in challenging applications. The Interceptor uses a simultaneous multi-frequency operation that effectively processes the transmission and reception of multiple frequencies continuously over a broad spectrum. This revolutionary operation facilitates an improvement in detection capabilities of up to 100% with stainless steel, especially when inspecting traditionally difficult “wet” products.
