Showing results: 271 - 285 of 407 items found.
-
Honeywell International Inc.
To install the optional cable sensor, simply plug it into the detector. The entire length of cable is an extended sensor. Additional 4 foot cable sensors (sold separately) can be connected to extend the cable and increase water sensing area even more. Note: The cable sensor jack is NOT for plugging in a power adapter. Doing so could damage the detector.**
-
Mors Smitt Group
A latching relay is a two-position electrically-actuated switch. It maintains either contact position indefinitely without power applied to the coil. It is controlled by two momentary-acting switches or sensors, one that 'sets' the relay, and the other 'resets' the relay. The latching relay maintains its position after the actuating switch has been released, so it performs a basic memory function.
-
DMS-05 -
Teledyne Marine TSS
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.- Low power, cost-effective solution
-
Site Sentinel -
Teledyne Gas & Flame Detection
Each system includes a tripod, network HMI, gas detection sensor(s), and alarm warning devices. An optional Sentinel SiteWatch provides remote access to system data via Ethernet or cellular communication. Power to the sensor assembly is supplied by a rechargeable Smart Battery Pack, disposable batteries or directly from HMI. Flexible and expandable, a Site Sentinel network can include up to 32 devices and consist of any combination of wireless and/or wired sensors, one or more HMI panels and optional solar panels. Additional sensors and/or remote alarm stations on tripods can be added as needed to assure widespread alert to site personnel.
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitter for load cells and the evaluation of strain gages in 6 mm housing with calibrated range selection.Detection signals from sensors for physical variables such as displacement, angle, pressure or force. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
RINKO III -
JFE Advantech Co., Ltd.
Rinko III is an analog version with the fast optical DO sensor and a temperature sensor. With an external 12 DCV power, the instrument seamlessly outputs the analog data (0 to 5V) of the sensors. Rinko III can be easily integrated on various platforms with an Impulse cable. By the fast response, the instrument provides high accurate DO data without restricting profile speeds.
-
Analog Devices Inc.
Analog Devices’ breakthrough current-to-digital converter technology is backed by award winning expertise to help solve your medical, industrial, and security application needs. Our high speed, high resolution ADC modules enable improved CT scanner data acquisition, photodiode sensors and power monitoring, spectroscopy, and high channel count data acquisition systems.
-
GM8037 -
UC Instruments, Corp.
UC INSTRUMENTS’ GM8037 portable high resolution fiber grating sensor instrument is ahigh power with high accuracy and wide dynamic range for fiber Bragg grating (FBG)sensors, and compact PC-based interrogation system, and is also a high accurate opticalspectral analysis system. It includes an external device, PC-based application software andoptional high performance laptop.
-
Auto -
CanDo
The CANdo AUTO Module is a rugged, multi-purpose CAN bus module with a USB port, two precision analogue inputs & a DC power supply input. The module is capable of operating either connected to a PC, or in a standalone mode powered from a 12 or 24V DC supply, such as a vehicle battery. The module maybe used as an interface between a PC & a CAN bus, or between analogue sensors & a CAN bus, in standalone mode. In addition, the module maybe programmed to transmit fixed, periodic CAN messages automatically on power up.
-
779521-01 -
NI
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
780264-01 -
NI
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
780264-02 -
NI
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
CozIR®-LP -
Gas Sensing Solutions Ltd.
The CozIR®-LP is part of a new generation of ambient CO₂ sensors optimised for low-power applications. The CozIR®-LP uses NDIR solid-state LED optical technology to create a sensor with a small footprint and ultra-low-power consumption. This makes it ideal for a new generation of portable and battery powered ambient measurement applications that require highly accurate CO₂ measurement capability.
-
Ultima® X -
MSA
The Ultima X Series Gas Monitors with X3 Technology bring the power of multi-sensing, signal boost and ModBus output to the Ultima X line of MSA gas monitors. The units are crafted from either stainless steel or NEMA 4X-rated plastic, and our patented SafeSwap sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification.
-
Spectrolab Inc.
InGaAs PiN sensors and sensor arraysTelcordia qualified InGaAs P-I-N photodetector device dies for the telecommunication, laser power monitoring, test systemsActive area sizes from 25 μm to 1 mm.Device die characteristics with low dark current, low capacitance and high quantum efficiencyWafer capability: 2", 3" and 4" on InP substratesHigh volume and low cost production
