ROM Emulators
A debugging tool that assumes the role of a system resource to examine and change memory, I/O, and registers.
-
Product
PathWave BenchVue Advanced Battery Test And Emulation
BV9210B
-
The BenchVue Advanced Battery Emulation Software helps determine your device's power consumption, emulate battery, and import existing battery models.
-
Product
JTAG Emulator
Spectum Digital XDS560v2-STM
-
The Spectrum Digital XDS560v2-STM emulator has System Trace capability, along with a USB powered interface.
-
Product
Lightning "Emulator" Shield
SEN-39002
-
Arduino shield, ideal for AS3935 lightning sensor development. The lightning "emulator" generates a RF signal that mimics lightning strikes. This board is in an Arduino Uno form factor, and only uses GPIO and I2C, so can be stacked on many form factors (developed on an Uno and Mega).
-
Product
Chromatic Dispersion Emulator
CS-CDE
-
The ClearSpectrum™-CDE is a chromatic dispersion emulator suited for test and measurement. This 1U half 19-inch rack-mountable module is designed to emulate tens of thousands of picoseconds per nanometer in a compact unit while maintaining very low insertion loss. It is a passive, ready-to-use emulator which can be cascaded several times to achieve higher levels of dispersion.
-
Product
Accessories: Intermittent Fault Emulator
-
The Intermittent Fault Emulator (IFE) is the solution. The IFE enables manufacturers, suppliers and operators of any Intermittent Fault Detection (IFD) tester to demonstrate and verify its capabilities to detect and isolate intermittent faults.
-
Product
C-SGN Emulator
-
The C-SGN Emulator combines the MME, SGW, and PGW functions, simulating the optimized EPC network required for CIoT. As part of the NetTest suite, the C-SGN Emulator creates an end-to-end lab environment for testing functions and features that characterize enhanced Machine Type Communication (eMTC) and Narrow Band Internet of Things (NB-IoT) implementations. In order to reduce complexity in the setup of a test environment, it also supports simulation of SMS Central Function (SMS-SC) and the Service Capability Exposure Functions (SCEF).
-
Product
Emulators
-
Comware Technical Services, Inc.
Comware’s emulators replace your legacy system with modern hardware without changing the operating system and the application software.
-
Product
Car-to-X Signal Strength Emulator
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
Product
Emulates Atmel T89C5111
FE-5111
-
* Emulates Atmel T89C5111 * 4K Code Memory * Real-Time Emulation and Trace * Frequency up to 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
IMS-SIP Network Emulator Software
E6966B
-
Wireless telephony networks are increasing capacity for high throughput Internet Protocol (IP) packed-data by utilizing radio access technologies such as LTE and HSPA. Session Initiation Protocol (SIP) and IP Multimedia Subsystem (IMS) are progressively being adopted as part of the network infrastructure to carry traditional wireless telephony services over an all-IP network. SIP provides control of communication sessions whilst IMS is the framework that allows delivery of multimedia services over IP. With this new capability comes the need for developers and operators to move their focus to testing user equipment (UE) in this new network environment.
-
Product
PoE LLDP Emulation (PSE) & Analysis for 802.3at & 802.3bt
-
The IEEE 802.3 specifications require that Type 2, Type 3, and Type 4 PDs implement PoE LLDP and use the Power via MDI TLV for power negotiation. This requirement therefore applies to any PD that draws more than 13 watts. The PDA-600 family includes an option to flexibly emulate any PSE while capturing and analyzing the LLDP power negotiation protocol from a PD.
-
Product
Smart Network Emulation for All Mobile Device Tests
CMWcards
-
Use R&S®CMWcards to prepare the tests you always wanted, but never found the time to set up. Create wireless signaling and application tests on the R&S®CMW500 wideband radio communication tester just by setting up a hand of cards – no programming required. Revolutionary card wizards and unique game rules guide you through setting up test sequences that fully comply with test specifications. Thanks to the R&S®CMW500 tester’s unrivaled multi-technology capability, R&S®CMWcards can be used to rapidly reproduce signaling scenarios for various wireless communications standards.
-
Product
Low Cost Emulator
EB-51X2
-
* Emulates 8051 Derivatives with 6/12 Clocks/Cycle * 64K Code And 64K Data Memory * Memory With Mapping Capabilities * Real-Time Trace * Frequency Range up to 40MHz * Source-Level Debugger For C And Assembler * MS-Windows Debugger Software * Performance Analyzer * Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115Kbaud
-
Product
Mobile Network Emulator
-
Qosmotec Software Solutions GmbH
QPER Mobile Network Emulator enables engineers to simulate handover scenarios in mobile networks without a fully-fledged test lab. Based on Qosmotec’s QPER technology, it allows to test UE and SIM-Card behaviour in a completely emulated mobile network: Cells can be configured with all relevant cell parameters (MCC, MNC, LAC, CI, etc.), SIMs can be added to the HLR, and UEs can use standard circuit switched and packed switched services. Thus, the QPER Mobile Network Emulator emulates the all components of a mobile network – consisting of core and radio functionality – and creates RF signals. It supports GSM, GPRS and EDGE (900 MHz, 1800 MHz) as well as UMTS (2100 MHz).
-
Product
Satellite and AerospaceChannel Emulation Toolset
S8825A
-
Satellite, aerospace, and airborne radio link testing with realistic wireless propagation conditions. 5G NTN test support with satellite connection from mobile phones. Interconnecting networks for full end-to-end system testing.
-
Product
JESD22-A115 Machine-Model (MM) Pulse Emulator
MM-10A
-
High Power Pulse Instruments GmbH
- Pulse unit to generate JESD22-A115 machine-model (MM) waveforms with TLP- Extremely stable and reproducible machine-model (MM) waveforms- Compatible with HPPI TLP-3010C/4010C/8010A/8010Csystems which have installed pulse width of 25 ns and rise time of 100 ps to 300 ps- Up to ±10 A machine-model peak current with TLP-3010C, which is equivalent to ±667 V (MM)- Up to ±15 A machine-model peak current with TLP-4010C, which is equivalent to ±1000 V (MM)- Up to ±30 A machine-model peak current with TLP-8010A and TLP-8010C, which is equivalent to ±2000 V (MM)- Same measurement procedure as TLP including DC test of the DUT- Compatible with HPPI TLP software and waveform data storage and management- 50 Ω SMA input and output connectors- Compact size: 61 mm x 25 mm x 17 mm
-
Product
Emulates Atmel T89C51RD2 in 68-PLCC package
FE-51RD2\68P
-
* Emulates Atmel T89C51RD2 in 68-PLCC package * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Battery Emulator And Profiler
E36731A
Battery Simulator
The Keysight E36731A battery emulator and profiler is an integrated electronic load and power supply developed to use with Keysight PathWave BenchVue battery emulation software. An emulated battery gives you a known good reference for testing at any charge level. Quickly assess the effect of design or software changes on battery life by emulating any battery charge state. Leverage emulation and precise current drain analysis to achieve longer battery life or to reduce the size of your device.
-
Product
Live PD Emulation for the PSL-3424A/L
-
Flexibly Mimic Class 0 to Class 8 Powered Device Per PSL-3424 Test Port. Configure up to 96 IEEE 802.3 PD’s on Any Combination of 2-Pair and 4-Pair PSE Ports with Loading up to 100W on Every Port. Emulated PD’s Automatically Handle PSE Power Demotions (Assigned Class). User-Defined Powered Device Load with Optional Cable Loss Modeling. Emulate 802.3at and 802.3bt PoE-LLDP* Negotiations and Power Adjustments (PSL-3424L). Monitor Multi-Port Live Emulation Status.
