Voltage Dividers
Circuit whose output voltage is a fraction of it's input voltage.
See Also: High Voltage Dividers, Frequency Dividers
-
Product
Surge Voltage Generator
SSG 500
-
Cable fault location with the BAUR SSG 500. The SSG 500 surge voltage generator is arranged in a 19'' housing. Maximum safety is achieved with the electrical safety control unit, the automatic discharge unit, the fully enclosed design and separate protection and system earth.* 6 output voltages up to max. 16 kV available* Electromagnetically actuated surge switch* Preselectable surge energy: 288 / 512 Ws (in all voltage ranges)* Automatic discharge unit
-
Product
Additional Products: High Voltage 50 Pin D-Type Cables - Connector to Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Continuity of Insulation Tester (High Voltage Method)
ZGQ-16B
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-5;Inspection standard: JB/T4279.13-2008Meet GB/T6109-2008 standard requirementsUsed to test the Insulation continuity (namely the pinhole number of enameled wire sample per unit length) of enameled round wires with nominal conductor diameter ranging from0.05mmto1.60mm;8 level test voltages can be selected by pressing button: 350V, 500V, 750V, 1000V, 1500V, 2000V, 2500V and 3000V;Test length ranging 0～99m;Application of SCM control.Automatically complete test process, display wire testing length and pinhole number;Brushless driving motor, guide pulley and take up pulley are equipotent.The electrode insulation to ground, using high resistance material of non-hygroscopic, no leakage, no tracking, easy to clean, Insulation thickness can ensure long-term 3000V voltage effect.Circuit board is subject to anti-static and moistureproof and long-time aging treatment, has more stable quality and higher durability;
-
Product
3 Phase Voltage Extension To Turns Ratio Meter
T-REX
-
The Raytech three phase voltage system option T-Rex is an optional system accessory for 3-Phase transformer ratio meter test sets designed by Raytech (i.e. TR-MARK III). T-Rex was designed to give Engineers and Test Technicians the ability to test the phase relationships and actual voltage ratios of transformer windings while applying three phase voltage.
-
Product
Stand Alone Low Voltage Tester
Model 64×2
-
Internal Memory: 8 program locations without test point labels or 2 program locations with test point labels. Removable Memory: 16 program locations without test point labels, or 4 program locations with test point labels.
-
Product
Standard Voltage 37 Pin D-Type Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
High Voltage Switching Test System
-
The advanced development of new technologies, such as SiC and GaN, have opened the opportunity for more efficient and higher voltage/power performance in switching and power management circuits. Their high cutoff frequencies, low on-state resistance, and very high breakdown voltages can increase power supply power handling densities approaching hundreds of watts/inch. Reliability of these new technologies and techniques is critical for realizing practical applications. While Silicon devices have a rich history of proven reliability, these newer compound semiconductor technologies are too new to have a reliability history and have not been well proven. Further, process variations, even in well-controlled lines, yield widely varying results. This has driven the need for additional testing and to burn-in devices prior to delivery.
-
Product
Voltage Converter
99539C
-
The model 99539C is an 8 channel wide dynamic range voltage to frequency converter of modular design.
-
Product
PXI 24 Channel High Voltage Multiplexer
40-320-101
Multiplexer Module
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
High Voltage Probe, 100:1, 3.7 KVpk, 500 MHz
10076C
High Current Probe
The Keysight 10076C 3.7 kVpk, 100:1 passive probe gives you the voltage and bandwidth you need for making high-voltage measurements. Its compact design makes it easier to probe today's small power electronics components, and its rugged construction means it can withstand rough handling without breaking.
-
Product
Deluxe Fused Voltage Leads
DFV
-
PowerSight DFV is a set of voltage leads that have in-line fuses. For added safety if a voltage lead shorts to ground via a cut in the insulation. Suitable for use to 1000V, includes replaceable fuses.
-
Product
High Speed High Voltage Amplifier
WMA-320
-
The WMA-320 is a high voltage, wide bandwidth laboratory amplifier. Its high output voltage, current and wide bandwidth have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-320 can be used for MEMS actuation, EO-modulators, PZT (piezo) positioners, ultrasonics, and many other applications.
-
Product
High Voltage Differential Probes
DP Series
-
Shenzhen Micsig Instruments Co., Ltd.
*Micsig DP Series High Voltage Differential Probes can be used with any brand of oscilloscope. *It adopts high-impedance isolation between the input and output to protect personal safety, converts the input high-voltage signal to a low-voltage signal for observation and analysis on oscilloscope.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-314-HI
Programmable Resistor Module
The 40-230-314-HI (PXI) and 42-230-314-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 470Ω with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High Voltage Diode Assemblies
-
High voltage diode assemblies are built by adding diodes in series to yield a higher peak inverse voltage. For example, if each diode is rated for 1200 peak inverse voltage (PIV), then six diodes in series would have a total peak inverse voltage of 7200 PIV. The detailed circuit is shown below.
-
Product
12-690V Voltage Tester With LED Display
7337
-
Peaceful Thriving Enterprise Co Ltd
Measurement by LED Display1. Double-pole Test2. High Voltage Indication3. Phase Rotation Test4. Polarity Indication5. Continuity Test6. Illumination
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-230-HI
Programmable Resistor Module
The 40-230-230-HI (PXI) and 42-230-230-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 6.97kΩ with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, Connector
40-230-256-HI
Programmable Resistor Module
The 40-230-256-HI (PXI) and 42-230-256-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 76.8MΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Non-Contact Voltage Tester With Wire Stripper
5227
-
Peaceful Thriving Enterprise Co Ltd
This product combines most required tools for an electrician to do the wiring job within the building, which includes screwdriver, non-contact voltage detector, illumination and wire stripper for most type wires.
-
Product
High Voltage 37 Pin D-Type Cables - Connector to Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a high voltage 37-pin D-type connector.
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-900-HI
Multiplexer Module
The 65-231-900-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Standard Voltage 9-Pin D-Type Connector & Cable Accessories
-
The Standard Voltage 9-Pin D-Type connector is used on PXI switching products to provide a low density connector solution. Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
Product
High Voltage Insulation Tester Module
DP-cPCI-5586
-
DP-cPCI-5586 is a High Voltage Insulation Tester Module. This module facilitates single-board voltage source/measurement features with high voltage output and a nanometer. Occupying a single slot in standard cPCI rack, this module can be used for multiple point cable harness test systems with limited rack space. Applications of this board include automatic test equipment, checkout systems, force voltage measure current, and insulation test.
-
Product
High Voltage Switching System
964i
-
The manual method is extremely problematic. Slow, error prone, labor intensive, operator hazardous – don’t even think about recording the test results. The 964i on the other hand, is purpose built to fully automate all of you HV switching needs. You chose the 964i, partnered it with a Vitrek 95X Series Industrial Strength Hipot Tester and QuickTest Pro test automation software. The company wins the Malcolm Baldridge National Quality Award, you get a promotion and that corner office you’ve always wanted. Choose carefully.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-136-HI
Programmable Resistor Module
The 40-230-136-HI (PXI) and 42-230-136-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 395kΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Universal Voltage Signaling PCI Card w/ 5 IP Slots
PCI5IP
-
If you want to use IndustryPack¨ modules with your PCI system then the PCI5IP is the choice for you. The PCI5IP combines features you need with simplicity and speed. Up to 5 IP modules can be installed. 32 bit and double wide modules fit right in. Each slot has independent operation - control, clocking, IO, power filtering and protection.
-
Product
sbRIO-9207, Non-Enclosed, 500 S/s, 16-Channel C Series Voltage and Current Input Module
781069-01
Current Input Module
Non-Enclosed, 500 S/s, 16-Channel C Series Voltage and Current Input Module - The sbRIO‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection. Non-enclosed modules are designed for OEM applications.
-
Product
80-1000V AC Non-Contact Voltage Tester
5226
-
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 80V~1000V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-310-HI
Programmable Resistor Module
The 40-230-310-HI (PXI) and 42-230-310-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
