-
Product
Electromechanical Testing Machines
-
Stand model in four-pillar design with electronic force transducer, flanged to the movable testing machine crosshead and electronic position transducer for measuring the crosshead path. The machine is driven by a quartz-precise stepper motor with two ball screws. Complete with integrated displacement measuring device 0.01 mm over the entire travel distance as well as additional displacement transducer with connecting cable and holder
-
Product
Frequency Response Analyzers
350C Series
-
Venable Model 350c is the 3 channel successor to the original workhorse Model 350a/b that launched in 1986 and established Venable Instruments as a market leader. The contemporary 350c Series incorporates a 3rd channel, allowing the user to measure more transfer functions simultaneously with one sweep, such as source and load impedance. The 350c is the only frequency response analyzer in the industry that can measure absolute phase, using a reference channel.
-
Product
DCA-M Sampling Oscilloscopes
-
Built on Keysight's digital communication analyzer (DCA) technology, the DCA-M family is recognized as the industry standard for verifying optical transmitter compliance to communications standards. With single to quad optical AND electrical channels in a compact form factor, the DCA-M is ideal for both manufacturing and RND applications. Analyze both multi-mode and single-mode signals with the low-noise, high-sensitivity calibrated reference receivers. The variety of models along with the supporting software and compliance applications ensure you can measure with high precision, whether you analyze electrical or optical devices.
-
Product
Torsion Testers
10k to 300k in.lbf (1,000 to 30k N.m)
-
For maximum versatility and capability, Tinius Olsen offers a full range of torsion testing machines in capacities from 10,000-300,000in.lbf or kg.cm (1000-30,000N.m). Higher capacity and other longer length models are available on request.
-
Product
Autoranging Power Supply
E36200 Series
-
The Keysight E36200 Series autoranging bench power supply can power devices that typically require higher output power supplies with larger watt ratings. A single output E36200 Series autoranging bench power supply can power devices requiring up to 200 W. In comparison, a dual output supply provides two independent 200 W outputs that can combine into a single 400 W output. Three technologies generate higher current at more voltages: autoranging, auto-series, and auto-parallel. All four models use autoranging outputs to provide maximum current at all voltages. Auto-series and auto-parallel internally combine the outputs of the dual output models, creating a single 400 W output.
-
Product
Benchtop DO/BOD Meter
LAQUA DO2000
-
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our compact and powerful benchtop model was developed to provide simplicity with excellent on-site usability.
-
Product
Cryogenic Temperature Sensors
Interchangeable Rox™
-
Ruthenium oxide temperature sensors are thick-film resistors, with most models suitable for use in magnetic field applications. These composite sensors consist of bismuth ruthenate, ruthenium oxides, binders, and other compounds that allow them to obtain the necessary temperature and resistance characteristics. Each Lake Shore Rox™ model adheres to a single resistance versus temperature curve.
-
Product
PCI Data Acquisition Boards
AD12-100DMA Series - Dual 12-bit A/D, 25 MS/s
-
Model AD12-100DMA is similar to the ADDA12-100DMA, but does not have D/A converters.
-
Product
Engine Torque Pulse Simulation
ETPS
-
HORIBA has revolutionized the way vehicle manufacturers test their Powertrains and Front End Accessory Devices. The ETPS dynamometer system accurately produces torsional pulse characteristics of an engine. This new technology employs a sophisticated mathematical model to calculate the resulting torque at the output of the engine based on engine and combustion process parameters.
-
Product
Analog Output Board with Arbitrary Waveform Generation
104-DA12-8A
-
Model 104-DA12-8A is a PC104 board featuring eight independent 12-bit digital-to-analog converters (DACs) and broadly configurable arbitrary waveform generation (ARB) capabilities. Other convenient features include 128K SRAM for waveform data storage, eight 4-20mA current sinks, three 16-bit counter/timers and fused general-purpose +5V and +12V power outputs. An economy version is available without the ARB feature as model 104-DA12-8.
-
Product
3D Software
Geomagic Design X
-
Geomagic Design X is an all-round, professional reverse engineering software with a smart combination of history-based CAD with 3D scan data processing, letting you produce feature-based, editable solid models compatible with your existing CAD software.
-
Product
Fracture Mechanics Clip-on Gages
-
3 models cover a broad range of gauge length, measuring ranges and temperatures, for fracture tests in compliance with various standards.
-
Product
Micromanometer
6700
-
The Handheld Micromanometer – Model 6700 can be used with pitot tubes, flow grids, differential pressure tubing, or the optional velocity-grid (for average face velocity readings). It comes standard with the Model 6715 TABmaster Capture Hood, but is also available for purchase separately.
-
Product
DIGITAL SATELLITE METER
1650S
-
The optimal satellite signal meter to test and measure both analog/digital signals(DVB-S, DSS). Especially, these models give users the capacity to measure 'C/N' very easily and correctly, which are very important measurement factors for the satellite broadcasting signal.
-
Product
Level Control Loop Trainer Model
ULP-24P & ULP-24C
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Level Control Setup comprises of acrylic measuring tank fitted with Level transmitter, control valve, I to P converter, source tank with water pump and necessary flexible piping for water circulation. The system is mounted on a table top powder coated metal frame. Level transmitter is of capacitance or DPT type sensor. The electronic panel comprises of ADC and DAC card with RS-232 interfaces.
-
Product
Draft Range Trasmitter
DR800
-
The Validyne Model DR800 Draft Range Transmitter is designed exclusively for very low pressure measurement needs. It has a "true" full-scale range as low as 0.25" H2O, making it ideal for air flow control applications. It can be turned down to 0.1" H2O; higher full-scale ranges to 100" H2O are available. The DR800 offers 0.5% accuracy and an operating temperature range of -20F to +185F. The total combined temperature effects are less than 3%/100F.
-
Product
Single connector for a HG cable, and two HM connectors
MVNA-8-350-2
-
The lower part of the Central Unit model MP-8-350-2 has a single connector for a HG cable, and two HM connectors (Fig. 9). Two Harmonic Mixers can work simultaneously, for instance HM2 detecting transmission through the DUT, and HM1, at port 3 of a directional coupler, detecting reflection from the DUT.
-
Product
Antenna Mast
Automated and Manual
-
Automated and Manually Operated Antenna Masts. The Com-Power AM series antenna masts are motorized and designed for EMI testing. Antenna mast Model AM-400 allows antenna height variation from 1 to 4 meters, and Model AM-600 can vary antenna height from 1 to 6 meters. They are constructed using non conductive fiber glass material. The antenna is mounted on a one piece cross boom, which is attached to a slider assembly. The slider assembly rides over the length of the mast on delrin wheels. It is pulled by a rope and pulley mechanism powered by a electric motor. The slider assembly is equipped with a spring loaded braking mechanism to prevent inadvertent descent should the rope fail.
-
Product
REMOTE-CONTROLLED SIGNAL GENERATOR
ASX-16C/D
-
Matrix Test Equipment Incorporated
The Model ASX-16C/D is a newer design version of the standard Model ASX-16C. The use of enhanced technology allows greater frequency trim (+/- 25 KHz) while maintaining the excellent noise and distortion performance of the ASX-16C. The Model ASX-16C/D also provides linear monotonic carrier level control over a 15 dB range in 0.025 dB steps
-
Product
High Range Chemiluminescence NOX-NO2-NO Analyzer
Model N200H
-
Teledyne Advanced Pollution Instrumentation
The Model N200H uses the proven chemiluminescence detection principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of high-level Nitric Oxide (NO), Nitrogen Dioxide (NO2) and total Nitrogen Oxides (NOx) gases for use in extractive type CEM systems.
-
Product
BF-Series Soft Stop Plus Models
-
The E-DRIV® BF-Series soft stop plus models is designed with an unique "soft-stop" shock absorbing clutch that is ideal for fastening shock sensitive components such as disk drives, plastics, and electronics. The ergonomically designed soft stop clutch reduces impact and vibration transmitted in the screw fastening process, which delivers less torque reaction to operator. The electric screwdriver offers a Double Hit Mode for soft joint applications and a selectable Soft Start mode. Designed for precision torque control the brushless motor design ensures durability and reduces the standard maintenance costs associated with brush type electric screwdrivers. The NF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
-
Product
Electrochemical Analyzer/Workstation
600E
-
The Model 600D series is designed for general purpose electrochemical measurements. The figure below shows the block diagram of the instrument. The system contains a fast digital function generator, high speed data acquisition circuitry, potentiostat, and a galvanostat (available only in select models).
-
Product
Analog Tank Test Kit
4108
-
The voltmeter included in the kit, the “Model IA” voltmeter, is designed for ease of use by meter readers and corrosion technicians alike and the voltmeter comes with an integrated RE-5 reference electrode attached for “metallic structure-to-soil” potential difference readings. The kit also includes a special test lead that has a brass thumb screw on one end which allows the test lead to substitute for the RE-5 reference electrode. This substitution allows the voltmeter to take “structure-to-structure” potential difference readings. The voltmeter offers a 0 - 2VDC range with a 10MΩ input impedance and the analog display presents a color divided scale for convenient indication as to whether or not a carbon-steel structure is receiving a suitable level of cathodic protection, with respect to the accepted 0.85V (850mV) threshold value.
-
Product
Transmission FT-NIR Spectrometer
QuasIR™ 1000
-
The QuasIR™ 1000 is an NIR analysis solution that brings together portability with unmatched spectroscopic performance. The QuasIR™ 1000 ensures direct calibration transfer without the frustration of standardizing instruments or adjusting models to accommodate excessive instrument variability.
-
Product
Torque Analyzers
-
You can reduce the risk of lost product on the line or failures in the field by using Mountz torque analyzers to ensure consistent quality. We have analyzers designed for the most efficient pass/fail assessments, models that use an internal computer to measure and display results in research and quality management environments, and even ones that connect to external torque sensors. Whatever variety you need, our torque testers are designed to fit into your processes and production environment.
-
Product
AC/DC Leakage Current Tester
228
-
Test for dangerous leakage current with the Simpson Model 228, designed to meet the latest UL, IEC, and ANSI specifications. The 228 detects both AC and DC leakage current and simulates human response at three different levels -- reaction, let-go, and burn hazard. Each Model 228 comes with test leads with alligator clips, manual, and batteries.
-
Product
DevOps & Agile Testing
-
While Agile and DevOps are progressive models, these need considerable evolution within the enterprise. TestingXperts, with its matured Agile and DevOps QA practices and extensive experience of test and lifecycle automation, helps enterprises build the right QA capabilities for Agile and DevOps. Within a fast-moving environment, it is important to ‘fail fast’ by adopting a ‘Shift left’ approach. With shorter testing window, it’s critical for the test team to start early and move at the same pace as rest of the teams. Test Automation also plays a key role in ensuring quicker testing execution and deploying continuous testing approach.
-
Product
6-Channel 200 MHz A/D and 4-Channel 800 MHz D/A with Virtex-6 FPGA - 6U VPX
Model 58620
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Six 200 MHz 16-bit A/Ds- Two DUC (digital upconverters)- Four 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM; 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Radiative Transfer Numerical Model
HydroLight
-
The HydroLight radiative transfer numerical model computes radiance distributions and related quantities (irradiances, reflectances, diffuse attenuation functions, etc.) in any water body.
-
Product
2-Ch 1 GHz A/D and D/A with Virtex-7 FPGA - 6U VPX
Model 58730
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1 GHz 12-bit A/D- One or two 1 GHz 16-bit D/A- 4 or 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
