-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - 6U VPX
Model 57660
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
GPS Master Clock
-
Signals & Systems India Private Limited
GPS Master Clock System – MCS-GPSMC-1010 is a 3U Card rack type, 19” Rack-mountable Redundant GPS Time Server which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using a signal obtained from any one of the sources like GPS or GLONASS or Time protocols such as NTP and IRIG. It distributing the same time signal through several types of interfaces. It provides redundancy for Power and GPS receiver to increase reliability and offers protection against time synchronization failure. The system is field-upgradeable and an extremely flexible system, designed to handle time synchronization requirements today and in the future. It provides nanosecond accuracy when external time references are not available. It has a storage facility to store the system log file. It delivers NTP, SNTP, IRIG-B, PFC-Pulse, DCF77, BCD parallel data, Ethernet Fiber Optic & RS485/RS232 outputs. System enables configuration and monitoring through Web-based application. It supports a wide range of power supply either 90V-260V AC/DC or 18-36VDC or 36V-72VDC. Power supply model can be mixed and matched as required by the user, depending upon power supply options available at the installation site.
-
Product
4kW Electronic Load
PT04-110
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 110V and 48V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
Product
Acute 112-Channel, 16-Event, 400Mbps, 256Mb/channel, Data/Pattern Generator
Acute DG3128B
-
Model / Data Channel / Event Channel / Pattern DepthDG3064B / 48 / 16 / 256Mb/ch (max)DG3096B / 80 / 16 / 256Mb/ch (max)DG3128B / 112 / 16 / 256Mb/ch (max)
-
Product
Digital Multimeters
-
Complete line of hand-held digital multimeters. Tough, reliable, economical professional DMMs in choice of 2000, 4000, 40,000, and 50,000-count models. Rugged, accurate and reliable.
-
Product
Exposure Systems
Model 2000AF & 2000SM
-
The OAI Model 2000 Exposure Systems may be configured as either an edge-bead exposure system (2000SM) or a flood exposure system (2000AF); both configurations are based on OAI’s proven, time-tested platform.
-
Product
Life-time Measurement System For Silicon Bulks/ingots By JIS Method
HF-100DCA
-
*Global standard model for the lifetime test of silicon bulk*JIS direct current anodizing method*Data processing by digital oscilloscope and PC with software
-
Product
3D Inspection Service
-
The reference data may come in the form of a table, with values at specific points or features, a cad model, or 3d scan. 3D inspection services may require datum measurements, where the part to be inspected is located in a fixture that is specifically designed to orient the part by an ordered method. In some cases, the part may have features that are designed specifically to be referenced by datums, if no functional feature of the part provides a clear reference.
-
Product
DC Hipot Tester
296
-
Our Model 296 is a simple-to-use Hipot Tester with the built-in ability to easily test Ground Continuity (Low Current Continuity). The 296 is capable of performing Hipot Tests in both AC & DC currents. You need a Hipot Tester that includes all the features you need to get the job done, the 296 has what you're looking for Make testing simple with common sense security settings.
-
Product
6-Ch 200 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 58621
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Six 200 MHz 16-bit A/Ds- Six multiband DDCs (digital downconverters)- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Two multiboard programmable beamformers- 4 GB of DDR3 SDRAM; 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Partial Discharge Measuring Equipment
-
Different from a conventional partial dischargemeasuring set provided with a fixed testingfrequency, Model DAC-PD-5 is newly designed toselect the center and the bandwidth of testingfrequencies so that partial discharges emitting in anoptional frequency in the range of a specifiedbandwidth can be detected. Generally, partialdischarges are measured in a wide band frequencythough; the detecting sensitivity must be lowered inorder to detect partial discharges partially.DAC-PD-5 has a wider bandwidth and can measurepartial discharges in a high sensitivity by bypassingnoises emitting bands.
-
Product
Transformer Ratiometer
TR-1C
-
Model TR-1C Transformer Ratiometer is a precision test set with an easy-to-read in-line digital readout from 0.00001 to 1.00000, suitable for testing all types of single and three-phase power distribution, potential and current transformers.
-
Product
Variable Attenuators
-
Variable attenuators are an integral part of most BER testing and EDFA characterization setups. All of EXFO's modular (IQS line) and benchtop variable attenuators are built for top performance and pinpoint accuracy. Each model offers a distinct set of features and specifications to suit various testing needs.
-
Product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - XMC
Model 71891
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Digital Instrumentation
-
National Meter Industries Inc.
* Wide range of models to measure themain parameters of the electrical network.* Very reliable and robust devices* Valid for work under demanding conditions
-
Product
Broadband, Multirange Directional RF Wattmeter
81050
-
With the Model 81050 Directional Wattmeter you can now measure RF power in 50-Ohm coaxial cable and transmission lines without the need for additional plug-in elements.
-
Product
Hand-held Tachometers
-
SHIMPO offers a wide range of hand-held tachometers that measure the total number of revolutions of a shaft or number of pulses of reciprocating equipment. Our models can measure and record last/min/max and up to 10 reading using up to 16 different units of measure. Our tachometers are designed for applications such as Motor Speed/Conveyor Speed/Fan Speed/Length Measurements that measure rpm of motors or shafts, either contact or non-contact with Laser style combination tachometer.
-
Product
Wall-Mount Enclosure
Model BOX
-
Model BOX is a wall-mount / bulkhead enclosure which provides environmental protection to IP65 / NEMA-4X. It comes with a 1/8 DIN panel cutout (45 x 92 mm) and can be used with 1/8 DIN instruments with a depth up to 134.5 mm (5.30"). This includes all 1/8 DIN instruments sold by Laurel Electronics.
-
Product
Light and Energy Meter
Model 656
-
OAI Model 656 Meter is designed for use with all mask aligners and flood exposure systems. For over 45 years, OAI is a world leader in UV Light & Energy Measurement Instrumentation used for reliable accurate calibrated control of the photolithography processes in the Semiconductor, MEMS, Wafer Packaging and Wafer Bumping Industries.
-
Product
Compact Autosampler
ASX‑280
-
Users call CETAC Autosamplers the best on the market, and it’s easy to see why. Put the most reliable, efficient and solidly built autosampler to work in your lab for sample analyses. We have a model to meet your needs, regardless the size of your lab or your specific technique, whether AA, ICP, ICP-MS, TOC, US-VIS, flash/prep chromatography, protein purification, liquid handling or others.
-
Product
PXI 32x8 Matrix Module, 1-Pole, 2A, 60W
40-586A-001
Matrix Switch Module
Our model 40-586A, along with the following models40-584, 40-585, 40-587Aare high-density single pole PXI matrices each supporting 256 crosspoints. All models use gold-plated contact electromechanical relays. The PXI matrix modules are designed for switching medium voltage and power signals. The user signal connection is via a robust 78, 50 or 37 pin D-Type or 160 pin DIN 41612 connector that is fully supported by the wide range of our cable and connector accessories.
-
Product
Functional Testing Services
-
We manage an in-house team of testing specialists having sufficient experience to perform quality functional testing activities.ImpactQA exhibits cross-browser & cross-platform testing capabilities together with the latest interoperability testing methods to assess functionalities across multi-faceted systems.Unlike other functional testing services, our testing model is loaded with adaptable properties to perform white-box testing and functional testing of Java and .Net applications.
-
Product
Handheld Oscilloscope
ScopeRider
Oscilloscope
When debugging embedded devices in the lab or analyzing complex problems in the field, the R&S®Scope Rider offers the performance and capabilities of a lab oscilloscope as well as the form factor and ruggedness of a battery-operated handheld device. Isolated channels combined with 500 MHz bandwidth makes it a perfect choice for power electronics applications. An integrated multimeter (two-channel model) or a multimeter mode (four-channel model) make the instrument the perfect tool for troubleshooting all kinds of electronics problems.
-
Product
Controlled impedance test system
CITS900s4
-
CITS900s4 is the seventh generation of Impedance test system from polar, and typically the most popular model for customers who are new to impedance control. CITS900s4 provides both differential and single ended measurement capability along with 4 channels to provide flexible probe connection.
-
Product
Flexible LXI Microwave Switch Platform
-
These flexible LXI microwave switch platforms (model 60-890) may be specified with a mix of high-performance microwave relays up to 67 GHz bandwidth with 50Ω or 75Ω impedance and a range of connector types.
-
Product
Stabilized Power Supplies
-
Stabilized power supplies are essential devices for providing stable DC voltage to electronic circuits and equipment.They offer features such as precise voltage and current regulation, short-circuit and overload protection, and advanced control functionality.Stabilised power supplies of our own design and manufacture can be built with output power up to 40kW even in models with 2- or 4-quadrant bipolar outputs.
-
Product
Sound Leveel Meter Software
SDK- Software Development Kit
-
The SDK provides functionality to establish connection and fully control the Model 831 and LxT Sound Level meters over USB, network or modem connections. File downloads are supported and the SDK includes documentation and software for extracting data from files.
-
Product
Trip, Auxiliary and Supervision Relays
6R Series
-
The 6R MATRIX range was developed to provide design engineers with a modular system of auxiliary relays to meet specific system configurations. The versions described in the following cross reference table have pre-defined functional & contact configurations to offer the following advantages:*Simple to specify & order*Lower cost due to model rationalization*Direct cross reference to other manufacturers models*Standardized wiring details
-
Product
PCIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.25 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4I.2223-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
10G Ethernet/IP Network Infrastructure Testing Application
GENEM-X
-
GENEM-X is a high-capacity network infrastructure testing software application for network equipment manufacturers, data centers, service provider telco cloud and 5G backhaul. It runs on Siama’s carrier-class PROVA-X hardware appliance. GENEM-X allows you to verify, monitor and troubleshoot Ethernet/IP network equipment and data center applications to ensure network services can accommodate the demands of your customers. Ideal for QA test, Service Providers migrating to a DevOps model can use GENEM to validate service turn-up and modifications in the production network. GENEM is equally at home in a lab environment. It bundles wire-rate traffic generation and analysis capabilities with a network emulator and packet capture/replay function in a single software license.
