Laser Diode Drivers
An integrated circuit that supplies modulated current to a laser diode in response to an input serial-data stream. (maxim-ic.com)
-
Product
Industrial 4-20mA Driver
-
Analog Devices portfolio of leading industrial d/a converters and drivers addresses the challenges of enhancing system accuracy, reliability, and overall functionality while reducing form factor and power dissipation. The products provide a range of programmable output ranges from standard 4–20 mA for current loop communication to ±10 V for actuator control. They simplify industrial system design by offering considerable control functionality and advanced on-chip diagnostics to maximize system up time. ADI industrial converters also eliminate the need for costly calibration routines needed by some traditional discrete architectures.
-
-
Product
Motor Driver ICs
-
The ST product portfolio offers a wide range of motor control ICs, well-suited for the most demanding automotive environments, covering the requirements of brushed DC motors, stepper motors and brushless DC motors, over an extensive range of voltage and current ratings. Efficiency and accuracy of our motor drivers are guaranteed by a unique combination of low-loss PowerMOS output stages and advanced control circuitry. Robustness and reliability are provided by the integration of a comprehensive set of protection and diagnostic features.
-
Product
Brushless DC Motor Drivers
-
ST’s STSPIN drivers for 3-phase brushless DC (BLDC) motors includes power drivers in a 3-phase bridge configuration and integrated solutions with built-in decoding logic for Hall-effect sensors.
-
Product
Transceiver Driver
S-112
-
Transceiver Driver slot module of FOTS system is an efficient module for the characterization of SFP type transceiver and the test of optical line or components. This module is a kind of Small Form Factor Pluggable(SFP) host board that can be used to test SFP transceiver modules to define the modules’ performance. The transceiver driver slot has two SFP cage and 20-pin SFP connector sets to mount and control two SFP transceivers simultaneously.
-
Product
Fiber Laser
ALiDAR Series
-
Amonics' high power fiber laser (ALiDAR) series offers eye-safe, single mode, linear polarized nanosecond-pulsed all fiber laser source with master-oscillator-power-amplifier.It is designed for three-dimensional imaging, wind detection and ranging LiDAR systems. The ALiDAR series is maintenance free with no post-installation service required. It is a versatile, ready-to-use and durable laser source for various LiDAR applications.
-
Product
Laser
BDS-MM Series
-
*Pulse Width Down to 60 ps*Repetition Rate 20 MHz / 50 MHz*Free Beam or Fiber Output*Optical Power Up to 40 mW*All Electronics Integrated*No External Driver Unit*Simple +12 V Supply*40 mm x 70 mm x 120 mm
-
Product
- Optically Isolated Line Driver
Model 72A
-
FEATURES: DC TO 19.2 KBPS; Optically Isolated; TD & RD LED's; Loopback Switch; Built-In Surge Protection; Male or Female Connectors; Screw Terminals and RJ-11. The Model 72A Optically Isolated Line Driver links RS-232 based devices over extended distances. It provides optical isolation and has built-in verification of operation using a loopback switch.
-
Product
Laser Diode Collimators, 520nm - 785nm, Elliptical Beam
-
The Optoelectronics Company Ltd
Custom lasing wavelengths and power options are available. Both standard and custom configurations provide OEMs, end-users and systems integrators with complete, cost-effective laser solutions.
-
Product
xDSL Line Drivers
-
Analog Devices xDSL line driver amplifiers provide industry-leading performance for cable set top boxes, cable modems, xDSL modems, and xDSL central office line cards. Due to our portfolio’s very low noise, high speed, and overall high performance, we provide designers with a top tier solution that is widely deployed as xDSL receivers. Applications for these products include wireless infrastructure, automated test equipment, multistandard radio receivers, point-to-point receivers and transmitters, instrumentation, and the military and aerospace industry.
-
Product
Modulator Driver
-
A compact bias control board designed to maintain the linear operating point of optical intensity modulators. Featuring a compact miniature design for OEM integration, the BCB-4 allows for a stable Q+, Q-, Min and Max operation over long periods of time. With a USB 2.0 DC power and monitor interface standard, the BCB-4 unit is the ideal choice for industrial and OEM applications when paired with any of Optilab’s wide variety of optical modulators. Please contact us at +1(480)719-1502 or email sales@oequest.com for more info.
-
Product
Laser Diode Driver
-
Fibotec offers special laser diode drivers, especially versions that accommodate laser diodes via integrated terminal bases. Two standard products for different applications accommodate laser diodes in butterfly packages with up to 2 A forward current. The "Pump Laser Pinout" is standard. The configuration for "Signal Laser" is available on request.
-
Product
Diode Tester
FEC VF40CM
-
Frothingham Electronics Corporation
The VF40CM is intended for testing VF, HALF CYCLE SURGE, and THERMAL RESPONSE/RESISTANCE on small- and medium-power diodes and rectifiers. It can also measure THERMAL RESPONSE/RESISTANCE on NPN and PNP bipolar transistors using an external user-supplied VCB supply.The VF40CM also is sometimes used to measure VZ of low-voltage zener diodes up to the compliance voltage limit of the tester. 20V at 20A is possible.
-
Product
Varactor Tuning Diodes
-
Macom Technology Solutions Holdings Inc.
MACOM’s GaAs and Silicon varactor tuning diodes provide broadband performance ranging from 10 MHz to 70 GHz. They are ideal for high Q filter and VCO electronic tuning circuits and are available in die form, flip chip, plastic and ceramic packaging. These GaAs diodes boast a constant gamma series for higher frequency and high Q applications and silicon abrupt and hyper abrupt series in plastic packaging are suitable for high volume surface mount applications.
-
Product
Clock Drivers
-
Multiple timing signals ("clocks") are required by CCDs, IR FPAs, and some CMOS image sensors to transport electrical charge across the array to a sense amplifier for conversion into image data. Pulse Instruments offers a line of "clock drivers" for generating these timing signals. The parameters of these clocks (clock rate, pulse width, pulse amplitude, rise- and fall-times, etc.) greatly influence the behavior and performance of the imaging device. Our products take logic-level inputs from a pattern generator and allow the user to adjust the output parameters to suit their device and testing requirements. Clocks can be "tweaked" in real-time to determine optimal operating parameters for a particular device, or else programmed in accordance with a test plan for automated production test.
-
Product
Laser Rotators
Zone Series
-
The powerful GeoMax Zone rotating laser portfolio offers the right construction tools for all trades and applications.
-
Product
RGB Video Driver
PCI900
-
The PCI900 is a PCIe form factor module that has dual RGB analog video receiver inputs. It outputs two analog RGBs that provide the capability to drive UXGA video up to 110 feet over coaxial cable. The input impedance is 75 ohms with a signal level of 1 VPPper RS-343A with sync on green. The output characteristic being 1 VPP into 75 ohms per RS-343A which can drive a minimum of 110 feet of cable.The PCI900 receives only power from the PCIe bus and has no other connection to the PCIe bus.
-
Product
Diode Laser Driver
D200
-
The D200 is a compact, DC-coupled fast laser driver, providing up to 4 amps of regulated constant current. A built-in edge-triggered pulse generator produces up to 1 microsecond pulse widths and 2 nanosecond transition times, capable of driving lasers with forward voltages up to 9 volts. A pulse-follower mode is also provided, accommodating externally-defined trigger widths up to 100% duty continuous-wave (CW). Power, pulse width, drive current and differential triggering functions are accessible through a ribbon cable header for embedded OEM applications. A low-inductance laser drive interface permits direct laser connection or custom interposer and flex-cable attachment.
-
Product
Laser
BDS-SM Series
-
*Pulse Width Down to 60 ps*Repetition Rate 20 MHz /50 MHz / 80 MHz / CW (Switchable)*Free Beam or Fiber Output*All Electronics Integrated*No External Driver Unit*Simple +12 V Supply*40 mm x 70 mm x 120 mm
-
Product
Big Easy Driver
-
The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It's the next version of the popular Easy Driver board.
-
Product
Diode Arrays
-
a silicon diode with minimal packaging overhead. The small signal 0603, 1005 and 1206 Chip Diodes are lead free with Cu/Ni/Au plated terminations while the other packages (SMA, SMB, SMC, 1408, 1607, 2010, 2419, 8L NSOIC, 16L NSOIC, SOT23, SOT23-6, 16L WSOIC) use 100 % Tin terminations. All Bourns® diodes are compatible with lead free manufacturing processes, conforming to many industry and government regulations on lead free components.
-
Product
Rad Hard Source Drivers
-
Renesas' radiation hardened source driver products reduce the size, weight and power of satellite subsystems such as command and telemetry control and communication satellite payloads, enabling satellite manufacturers targeting various mission profiles to significantly increase system capacity and reduce solution footprint by 50 percent.
-
Product
Laser Markers
-
Panasonic Industrial Devices Sales Company of America
With over 20 years of experience building Laser Marking Systems and 2D Code Readers, Panasonic has built a strong following that identify the brand with innovation, reliability, and quality. Throughout the years Panasonic has developed numerous high-quality products for a variety of applications only to be matched by their first-class customer service and expert technical support.
-
Product
Stepper Motor Drivers
-
Minimize noise and vibration in your stepper motor designs with our QuietStepTM adaptive stepper motor drivers. We offer a complete lineup of stepper motor drivers for office automation, industrial, and automotive applications. Our advanced QuietStepTM solutions use proprietary algorithms to reduce torque ripple and current distortion. To minimize ripple current for the various operating conditions, QuietStepTM adaptive stepper motor drivers perform on-the-fly adjustments to the amount of fast decay during a pulse-width modulation (PWM) cycle. This adaptive feature improves system performance, reduces audible motor noise and vibration, and increases step accuracy.
-
Product
Schottky Diodes
-
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
-
Product
LED Power Driver ATS
8491
-
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
Product
Extenders & Line Drivers
-
Extenders and Line Drivers enable reliable, long distance signal transmission over coaxial, twisted pair, or fiber optic cabling.
-
Product
Osram Direct Emission Green Laser Diodes (510 - 530nm)
-
The Optoelectronics Company Ltd
The PLT3 520D laser diode can deliver 140mW pulses at 520nm with 8% efficiency, driven at 300mA at 50% duty cycle – OSRAM's previous limit was 80mW with the PL 520B. This new diode has been developed to work in MEMS-based scanners.
-
Product
Laser Sources and Amplifiers
Amplifier
We design and manufacture a range of tunable C-band and L-band telecom laser sources, customizable fixed-wavelength laser sources, broadband super luminescent (SLED) sources, swept laser sources, and Erbium-Doped Fiber Amplifiers (EDFA).
-
Product
Laser Beam Positioning
-
Under the trade name of SpotOn we offer a wide variety of computerized position measurement systems.This is a family of cost-effective and versatile solutions to numerous industrial and laboratory applications.Among the measurement applications, are:Measure laser power and centration or displacementAlign beams and QC of optical systemsMeasure target rotation and displacementMonitor vibration, deflection and motion
