Discrete Semiconductor Testers
check connected individual semiconductor components.
-
product
Service Testers
Service tester with receiver probe, laser pyrometer, alligator clip cable, 10 inch handle, manual and standard bag.
-
product
SMD LED Aging Tester
Shenzhen Chuangxin Instruments Co., Ltd.
LED life tester with 150 independent constant current to aging-life and color comparisons of 50pcs 5050 SMD LED and 100pcs 3528 SMD LED.
-
product
Formaldehyde Content Tester
TF136
TESTEX Testing Equipment Systems Ltd.
Formaldehyde Content Tester, used for rapid determination of formaldehyde content of variable textiles. To simultaneously measure formaldehyde value and absorbance value by using the extraction method.
-
product
Transient Over-voltages Tester
SUG335
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
product
CT Tester
5000 Bird Dog Plus
Spinlab Utility Instrumentation, Inc.
he Bird Dog Plus is the most complete, easy to use CT test product available on the market! Spinlab has created the most innovative products available to perform meter circuit testing. All 32 failure modes of a meter circuit can be checked with the push of one button. You will be able to thoroughly evaluate any poly-phase meter circuit in less than 10 minutes.
-
product
Multifunction Installation Tester
COMBI519
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
product
Photovoltaic and Electrical Installation Testers
Photovoltaic electrical installation safety testing is a special area of electrical installation safety testing as it also entails tests and measurements on DC systems, which are relatively uncommon in most domestic, commercial and to a certain extent industrial environments. There is also the addition of photovoltaic-specific tests that are outside the realm of standard test and measurement procedures.
-
product
Handheld Contact Resistance Tester
Weshine Electric Manufacturing Co., Ltd
The hand-held Circuit resistance tester is an innovative product. The product is compact, hand-held operation, battery power supply, easy to carry. The product is mainly used in the measurement of contact resistance and other micro-Euclidean resistance of switch contacts. The test speed is fast and the accuracy is high.
-
product
Wiremap Tester
MicroMapper
Whether you're an electrical contractor, a home networking professional, datacom specialist or IT/network manager, the Fluke Networks family of powerful Voice/Data/Video (VDV) verification and troubleshooting tools will allow you to verify your work while delivering a quality installation.
-
product
Film Impact Tester
DRK136A
Shandong Drick Instruments Co., Ltd.
DRK136A Film Impact Tester is applicable in the precise impact resistance test of plastic films, sheets, laminated films, rubber and other nonmetal material.
-
product
In-Line Spark Tester
ST20610
Connect the tool between the spark plug and the plug wire to provide a quick visual check and diagnosis of the ignition system, including distributor-less ignitions. Plug wire is double-ended with a straight boot and a 90 boot for confined areas. With the engine running, the bulb mirrors the ignition spark.
-
-
product
Exhaust Back Pressure Tester
33600
Use to test for clogged or obstructed catalytic converters and mufflers. Fast and easy to use - threads into Oxygen Sensor Port. Includes 12mm and 18mm adapters to fit most domestic and imported vehicles. Gage measures 2 1/2" diameter and has dual scale: 15 PSI and 1.00 Kg/Cm2. Hose is 41" long.
-
product
Circular Blade Crosscut Tester
MCT-5
Is designed to test the adhesion and brittleness of dry coats of paint on their substrate by means of a set of six circular blades and two guide blades.
-
product
Phase Rotation Tester with Voltmeter
885 PR
Standard Electric Works Co., Ltd
● 3 functions in one unit: Phase Rotation, Phase Presence, Voltmeter● LCD contact type Phase Rotation Tester● Large LCD to show phase rotation and phase presence● Check a wide range of three phase power sources● Voltage range for phase rotation test: 75~600V AC ● Frequency range: 40~400Hz● 6000-count voltmeter● Auto ranging Voltmeter AC/DC● Data hold function● Auto power off● Convenient stand for viewing● Easy to use● Comply with EN 61010-1 CAT III 600V EN 61010-2-033 EN 61326-1
-
product
Receiver, 9050, 50 Module, Dual Discrete Wiring Tiers
310104368
The 50 Module Receiver is a rugged system devised to accommodate high I/O. With high contact point availability, the 50 Module Receiver is suited for larger test and measurement systems. Both tiers are designed for discrete wiring, and can accommodate individual 9025 ITAs.
-
product
Digital 12V Battery Tester
BT175
Schumacher Electric Corporation
DIGITAL TESTER FOR 12V BATTERIES/STARTER SYSTEMS/CHARGING SYSTEMSHand-held tester checks the battery, starting and charging systems with digital accuracyDigital display guides you through the testing process and shows voltage and CCALEDs indicate OK, OK & Recharge, Recharge & Retest, Weak, Bad Battery and Error For 12V SLI and VRLA/AGM/GEL batteriesAccepts rating types CCA, CA, EN, IEC, DIN and SAEOperating range: 100-1200 CCA (SAE)Testing voltage: 7-15VContents: (1) Schumacher BT175 Digital Battery Tester (1) owner's manual
-
product
CDM Tester
Tokyo Electronics Trading Co., Ltd.
Determine what level of CDM discharge causes device damage by placing the device package on a metal plate with the pins facing up.
-
product
Audio Impedance Testers
1107 IM
Standard Electric Works Co., Ltd
● Large LCD : 68 × 34mm(2.677" × 1.338").● True measurement of speaker systems actural impedance at 1kHz.● Three test ranges allow testing of home theater and commercial sound systems.● Measures transformer impedances.● Battery operation.● Low battery indication.● Data hold function.● 0Ω adjustment.
-
product
Partial Discharge Tester
GTPD-4C
GTPD-4C partial discharge comprehensive tester is the new generation of digital PD measurement and analysis instrument. The instrument has a strong ability of comprehensive analysis of partial discharge and detection of partial discharge in small signal and strong interference environment. With different accessories, it can measure and locate the partial discharge in any high voltage electrical equipment. It can realize testing the transformer partial discharge by applying the voltage on the three phases simultaneously.
-
product
Insulation with Low Ohm Tester
Wuhan Fanke Transformer Manufacture Co., LTD
Insulation with Low Ohm Tester
-
product
Digital Insulation Tester
SK-3502
125V/250V/500V/1000V, Comparator Function., Data Memory (up to 100 data)., Low Resistance Measurement., AC/DC Voltage Measurement., Enhanced Safety Functions.
-
product
CT PT Tester
HTFA-109 / 342
Wuhan Huatian Electric Power Automation Co., Ltd.
Used for automatic testing of protective and metrological CT/PT.
-
product
Battery Capacity Tester
BLU-A Series
The battery capacity test is performed to determine the health of a battery. DV Power’s battery load unit BLU-A is a portable, powerful, and lightweight solution for battery capacity measurement. It is applicable to any battery string such as lead-acid, Li-Ion, Ni-Cd, etc., with up to 500 V battery voltage. As a special feature, BLU100L model enables the capacity testing of a single Li-Ion cell.The capacity test is performed in an accurate and user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.Battery load unit BLU-A enables setting discharge currents up to 240 A, with a resolution 0,1 A. Furthermore, if higher currents are required, BLU-A units can be connected in parallel, or additional BXL load units can be used.The instrument offers the best power-to-weight ratio in the market. BLU-A models start from 12,8 kg / 28.2 lbs and deliver up to 28,4 kW of power.The user can select three discharge modes:Constant current,Constant power,Constant resistance.Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.The instrument monitors discharge parameters in real-time during the capacity test. A 4,3-inch touch screen display shows battery voltage, current, elapsed time, and capacity during the entire test. Also, BLU battery load unit can be used with DV-B Win software. As a result of that, a user can see a detailed numerical and graphical presentation of key parameters and can create reports in various formats.Testing with BLU-A doesn’t require a disconnection of the battery from the testing equipment.
-
product
Form Testers
The highly accurate rotary table machines and spindle form testers of the RONDCOM series can be used in many areas: production, measuring room and calibration lab.
-
product
Insulation Testers
AD-902
The instrument is designed for the direct measurement of insulation resistance of cables and electrical equipment especially in the telecommunications and communications. It can also serve as a tester for example go. Circuits or connectors.
-
product
Multi-Network Cable Tester
3PK-NT007N
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
product
Mobile Network Tester
Qosmotec Software Solutions GmbH
The main motivation for a subscriber to select a mobile network operator are the costs and the quality of the cellular network. Network coverage, reliability and performance are the key factors for customer satisfaction and influence many subscribers’ decision for service provider change. Qosmotec’s Mobile Network Tester LTS verifies the user experience of the mobile network for all relevant network applications and services and provides key performance indicators (KPIs) to assess the network quality.
-
product
Radiation Dose Testers
Handheld Radiation Dose Tester with high sensitive GM counter sensor, combined Beta(β ), Gamma(γ), and X-ray radiation detection. It is widely used in home decoration, radiation processing enterprise, health and epidemic prevention, radiation therapy, import and export inspection, building materials, petrochemical, geological survey, scrap steel, industrial nondestructive testing and other environments existing ionizing radiation, personal radiation dose supervision and protection occasions.
-
product
Durometer - Shore Hardness Tester
Qualitest provides quality control departments and research laboratories with an extensive range of top quality Durometer and hardness Tester for accurate hardness determination on all natural and synthetic rubber products and soft elastic materials, plastics, acrylic glass, acetates, casting resin, polyester, thermoplastics, PVC, neoprenes, hardboards, wood, leather, fruits and much more. Our products provide the highest precision (normally 0.5% or better), quality and craftsmanship, durability, “yet require” almost no calibration in many years after the purchase. Our designs are engineered so that the Durometer stays precisely within the standard requirements. Qualitest Durometers are referred to as the “Swiss watches” among other products on the market. Investing in our line of Durometer is a guarantee of accuracy and assurance for many years of operation.
